5.3 Workpiece Location and Clamping

Key Takeaways

  • A rigid body has six independent degrees of freedom. Positive and negative senses of each are twelve directions of motion in some fixturing texts.

  • For three mutually perpendicular seating faces, three primary, two secondary and one tertiary contact establish the pose when maintained.

  • In a two-hole location, use the round pin for planar position and the relieved diamond pin for the remaining in-plane rotation.

  • Direct force toward the seating contacts and support flexible areas. Evaluate sliding, lifting and tipping using the actual cutting forces and geometry.

Last updated: November 2026

5.3 Workpiece Location and Clamping

Define the part’s seated position

A free rigid body can translate along three axes and rotate about those axes. These are six independent degrees of freedom, each with two possible senses. Fixture references sometimes count twelve signed motion directions and describe how the stops block certain directions. In that terminology, motion away from a stop may remain possible until preload closes the contact. Twelve describes directions, while six describes independent coordinates.

A locator provides a repeatable contact reference. A clamp loads the work into its intended contacts and helps keep those contacts engaged. Hardware can combine functions. For example, a fixed vise jaw can provide a locating face while the moving jaw pushes the work into it. If the process uses a dedicated locator, avoid allowing a clamp to establish a different final part position.

Apply a 3-2-1 layout

Assume a rectangular part sits on a base, registers against a side and touches an end stop. In this example the base is the XY plane, with the work on the positive Z side. The side locators are on the negative Y side and the end locator is on the negative X side.

Contact setPhysical arrangementIndependent coordinates fixed with contact maintained
Three primary contactsNon-collinear pads beneath the bottom faceZ translation and tilt about X and Y
Two secondary contactsSeparated side locators with normals along YY translation and rotation about Z
One tertiary contactEnd stop with its normal along XX translation

Seat the part downward and toward the side and end references in the stated arrangement. The bare stops prevent penetration. A part can lift from a pad, pivot off a contact or pull away from a side locator unless the loading arrangement keeps it seated. For example, tightening a clamp above an unsupported web can lift a distant corner and create a wrong height reading even though all six locators are installed. Verify the actual contact pattern after tightening. In GD&T the datum reference frame is established according to the feature control frame and its applicable rules. A manufacturing fixture can carry over the desired reference features, and the drawing and inspection plan still govern the measurement datum setup.

Separate primary pads to give a stable contact triangle on sound material. Chips, burrs, rough casting profiles or poorly placed clamps can defeat the seating. A fourth rigid support in an uneven plane may compete with the first three. An adjustable or lockable support can carry cutting force under a web after location has been established. It should contact and lock as designed without lifting the part off the primary pads. Verify the supplier’s load and sequence requirements. That supplementary support serves a different role from a fourth rigid locating pad.

Locate with two holes on a base

For a plate seated on its primary pads, a round pin in the first hole locates its X and Y position within the fit. A diamond pin in the second hole constrains the remaining in-plane rotation. If the holes lie along X, arrange the diamond pin so its locating lands contact across the hole in Y and its relieved sides allow spacing variation in X. Turning the relief the wrong way can retain the binding and weaken the orientation control.

Two tight round pins can bind if the manufactured hole spacing differs from the fixture pin spacing. The needed relief and remaining location uncertainty depend on pin size, hole limits, clearance, spacing and required orientation. Verify the actual tolerance stack. Try a representative part and the expected size range through the approved fixture prove-out. Forcing the plate onto the pins can damage the contacts and mask a seating fault.

Trace the forces

Start with likely direction and point of application of the cutting load. Arrange positive stops or supported faces to react that load where practical. Check the tendency to slide, lift or tip, even when the cut appears to push toward one stop. Use suitable part and clamp contact areas to avoid part deflection or damage. Check force and moment balance and the manufacturer’s limits before setting the clamp load.

For a simplified example, a horizontal reaction of 150 lbf acting 2 in above a pivot edge creates a 300 lbf·in tipping moment. If a vertical clamp whose line of action is 3 in from that pivot is the only resistance to tip in the model, it takes 100 lbf at incipient tipping. That is a threshold in a simplified model. Actual loads can vary with engagement and tool condition. Check other reactions, friction, load variation, margins and allowable part deflection in the approved setup. A multiplier on cutter force alone cannot account for these lever arms and support conditions.

When an unsupported thin web deforms, consider moving the clamp onto sound material, supporting the web without relocating it, or spreading the force. Verify the released part as well as the clamped part. A flexible part can spring back after the fixture releases and change a surface that measured well in the machine.

Carr Lane locating and clamping, Carr Lane diamond pins, Vektek locking work supports and rigid-body motion coordinates

Loading diagram...
Maintained Contacts in a 3-2-1 Fixture
Test Your Knowledge

With contact maintained on the three non-collinear pads of an XY base, which independent coordinates does the base establish?

A

Only translation along Z

B

Z translation and rotation about X and Y

C

X and Y translation and rotation about Z

D

All six independent coordinates

Test Your Knowledge

The centers of two locating holes lie along X. How should the diamond pin for the second hole be oriented in this fixture?

A

Its locating lands should restrict X only

B

It should allow unrestricted movement along Y

C

Its relief should accommodate X spacing variation, with locating contact across Y

D

Its lands should make the same full round fit as the first pin

Test Your Knowledge

A thin web springs back when clamp pressure is released, and final flatness fails. What change addresses this mechanism?

A

Increase torque on the same unsupported span

B

Add a taller fixed locating point to force all faces to touch

C

Compensate only by changing the tool diameter offset

D

Relocate or support the clamp load so it does not bend the web during cutting

Test Your Knowledge

A static model has a 240 lbf·in tipping moment. What vertical force at a 4 in perpendicular arm balances it if this is the only resisting moment?

A

60 lbf

B

240 lbf

C

960 lbf

D

4 lbf

Sections you finish are checked off in the contents.