5.2 Turning Workholding and Support

Key Takeaways

  • Use a self-centering chuck for compatible stock or an independent chuck to adjust the position of a chosen feature. Verify the assembled part with an indicator where required.

  • Select the workpiece collet, chuck action and gripping length from the actual system, stock and load. Drawback and dead-length systems can position a part differently in Z.

  • For external gripping, centrifugal load on rotating jaws can reduce net grip. Preset pressure and catalog speed alone cannot qualify the assembly.

  • Support shaft work using the machine and workholding instructions, free span, rigidity, load and imbalance.

Last updated: November 2026

5.2 Turning Workholding and Support

Select a holding arrangement

In turning the work rotates with the spindle. Verify clamping before rotation and use an approved work envelope, force and speed for the complete setup. A speed rating for a bare chuck does not account for large or heavy jaws, irregular parts, reduced contact area or feed forces. Follow the machine and chuck maker’s procedure for hand checks, adjustment, safe access and guarding.

DeviceLocating functionCheck for this job
Three-jaw scroll chuckA common scroll moves the jaws together to center compatible stockJaw form and condition, grip range, repeatability on the reference surface
Four-jaw independent chuckIndividual jaws allow adjustment to center the desired feature, or set a specified eccentricity where approvedContact and secure engagement of all jaws, imbalance, and speed limit for the setup
Collet chuckA selected bore or profile grips stock within the actual collet’s working rangeUsable gripping length, profile, size range, machine and closer compatibility, and axial shift
Centers with an approved driverRegister the work on center holes so the part can use the same references in multiple setupsClean, sound centers and holes, appropriate load and lubrication, secure drive and clearance
Expanding mandrelUses the existing bore as the workholding reference for exterior machiningActual bore condition and range, engagement, permitted drawbar force and axial seating

Indicate the feature you want to center

South Bend’s independent chuck procedure calls for bringing the jaws into contact, tightening in small opposing increments and checking the selected feature, with one jaw loosened slightly as its opposite is adjusted to refine position. Set the machine to the safe condition specified by its manual before handling or rotating by hand. Use a suitable circular locating surface or a defined target for the feature. A rough cast skin can vary from roundness as well as eccentricity. An indicator range on that skin does not identify the offset of an intended bore axis.

For example, suppose a reference journal is round in the indicated section and the largest and smallest indicator readings are +0.003 in and −0.001 in. Their difference is 0.004 in. Under the round-section assumption, radial offset is half that range, or 0.002 in. Use this as a guide to measured workpiece displacement. Jaw screw motion and final centering have to be checked on the actual part. Compare a second station if the feature might be tilted. Recheck after final tightening and remove the chuck key and indicator before running.

Distinguish collet design and grip

5C, 16C and 3J designate workholding system families. Hardinge offers different nose and grip forms for these families. Select the exact collet matching the machine, stock profile, diameter and finish, and verify the actual gripping zone and load limits. A split collet contacts the work through its fingers. Grip depends on the fit and contact over those surfaces. A 5C label cannot supply a universal runout or grip-length result, and workpiece engagement is a different application from gripping a milling tool shank in an ER collet.

For the Haas Chucker Lathe, Haas describes a standard draw-back collet that can pull the work axially during closure, with shift varying as bar diameter changes. A dead-length system is designed to limit that motion, supporting repeatable axial positioning. Verify the stop arrangement and check the actual face position after closing. Hardinge offers specific dead-length 5C and 16C assemblies. Check the particular construction rather than inferring axial behavior from the size family.

Prepare soft jaws and account for speed

Use jaws and fasteners that fit the chuck’s serrations, stroke and slots. Haas’s power-chuck soft-jaw procedure calls for a compatible support slug or boring ring in the usable portion of jaw travel before machining the jaw pocket. Verify contact on a production part. For thin rings, broad-contact pie jaws can spread the load and reduce deformation, but check bore form after releasing the part. Use the permitted force and verify retention at speed. High clamping pressure can distort or tip jaws and reduce contact.

A boring-ring rating can differ from a production rating. Haas lists 700 RPM and 113 psi maximum in its HJB-08 boring-ring table for part 05-0512. Treat those as limits for that fixture under the stated conditions, and use the lower applicable equipment limits. For an internal-gripping setup, verify the correct support direction and model procedure before machining jaws.

For a rotating jaw component of mass mm at center-of-mass radius rr, the outward force term used in a rotating-frame calculation is mω2rm\omega^2r, with ω\omega in radians per second. Doubling speed quadruples that term with fixed mass and radius. The complete chuck’s gripping force involves its jaws, mechanism and direction of gripping. For external gripping, the outward load on the jaws typically reduces available inward grip. Use the chuck force-versus-speed data for the actual jaws and permitted pull or pressure. For internal gripping, follow the distinct manufacturer limits. For example, Kitagawa’s B-200 series specifies internal grip drawbar pull below half its listed external maximum. The separate gripping rules address a different load path.

Review support for long work

An approved tailstock center can support the far end. A bearing-equipped live center turns with the work, while a tailstock dead center provides a stationary contact that requires the proper setup and lubrication. A lathe dog and drive plate transmit drive in a compatible between-centers setup. A steady rest can support a fixed section of the work. A follow rest, where the machine provides one, travels with the cutting carriage. Inspect support and tool clearance across the cutting envelope.

Assess free length, section stiffness, material, imbalance, speed and tool load. Haas RD0036 Revision A gives Haas-specific chuck/part-weight guidance and calls for tailstock or steady-rest support in its greater-than-3:1 case. This guidance is no substitute for the model’s speed, weight and workholding limits. An expanding mandrel is another application-specific choice. Hardinge Sure-Grip instructions provide force limits for individual expanding collet models. Size the grip to the actual bore and confirm the measured relation of the new OD to its specified datum.

South Bend workholding, Haas Chucker Lathe, Hardinge Sure-Grip, Haas lathe troubleshooting, Haas HJB boring-ring limits, Kitagawa B-200 and Haas RD0036

Loading diagram...
Checks for a Turning Workholding Setup
Test Your Knowledge

A round reference journal shows +0.002 in and −0.004 in at the indicator extrema. If the section is round and the measured range is entirely due to eccentricity, what is its radial offset?

A

0.006 in

B

0.002 in

C

0.003 in

D

0.004 in

Test Your Knowledge

Why might a dead-length system help control the face position when closing on bar of slightly varying diameter?

A

It is designed to limit axial workpiece motion during clamping

B

It expands the diameter of the stock to fit the collet

C

It removes the need to set and check the stock stop

D

It makes the radial runout equal to the bore tolerance

Test Your Knowledge

A thin ring measures round while clamped in three narrow jaws and lobed after release. What setup change directly addresses the likely cause?

A

Increase force using the same narrow contact

B

Use a higher speed to loosen the contact during the cut

C

Set the same offset to compensate for each lobe

D

Evaluate approved broad-contact pie jaws and check the released part

Test Your Knowledge

A permitted jaw, with the same mass and center-of-mass radius, turns at twice its earlier speed. What happens to its outward centrifugal term?

A

It doubles

B

It quadruples

C

It halves

D

It is unchanged

Test Your Knowledge

Does selecting a 5C workpiece collet establish the required gripping length?

A

Yes, the minimum is twice the bar diameter for all collets

B

Yes, the inserted length always equals the exposed length

C

No, verify the approved collet/chuck, contact, stock and load for this setup

D

Yes, the bore diameter gives a fixed axial length for the family

Sections you finish are checked off in the contents.