6.6 Profile and Runout Tolerance Zones

Key Takeaways

  • Profile of a line evaluates designated line elements. Profile of a surface applies a zone to all indicated surface elements together.

  • A centered profile zone divides its total width equally. A value after the ASME unequally disposed symbol allocates the amount toward added material.

  • Circular runout is evaluated by circle, while total runout uses one zone over the indicated surface relative to the datum axis.

  • Concentricity and symmetry on an older ASME drawing have edition-specific meanings. Select the applicable drawing edition before interpreting them.

Last updated: November 2026

6.6 Profile and Runout Tolerance Zones

Read the profile and where it applies

The true profile is defined by basic dimensions or controlled model geometry. For a uniform tolerance, the boundaries follow the true shape and are spaced in the direction normal to it. Profile of a line applies to a designated line or set of sections. Profile of a surface applies to the whole indicated surface as one entity. The leader, limit marks, extent symbols, notes and datum references govern the specific case. A profile control without datums can control form, while datum references constrain the zone’s orientation and location as indicated by the frame.

A centered uniform surface profile zone 0.012 in wide allows signed departures from −0.006 to +0.006 in in a fully constrained reference frame. Define the positive direction as adding material to the nominal part. For the ASME callout 0.012 Ⓤ 0.008, 0.008 in is allocated in the direction of more material and the other 0.004 in in the direction of less material. The resulting interval is −0.004 to +0.008 in. For the same total width, Ⓤ 0 places all tolerance into the direction of less material. Look at which side contains solid material. For an internal wall, adding material fills some opening even when the displacement is toward the feature’s center. Section 7.6 shows how to compare measured data to an aligned profile.

Compare circular and total runout

Runout controls surface variation relative to the resolved datum axis. Use the datum features the drawing names. An arbitrary chuck or a zeroed indicator alone cannot establish that axis. The following table applies to common cylindrical journals and flat end faces.

CalloutCylindrical surfacePlanar face normal to the datum axis
Circular runoutSeparate concentric circular zone at each station, centered on the datum axis. Radial contact tracks variation through a full turn at one station.Separate circular trace at each specified radius. An axially oriented indicator checks variation through a full turn at a fixed radius.
Total runoutA single pair of coaxial cylinders separated radially by the stated value, aligned to the datum axis, contains the indicated surface simultaneously.A pair of parallel planes normal to the datum axis contains the whole indicated face. Keep a common axial reference while surveying the face.

For total radial runout, cover the controlled surface with the approved axial traverse and rotation or an equivalent measurement strategy. Use a common reference for the extrema. Resetting to zero at every station removes the between-station variation needed for an overall check.

Suppose the referenced axis is established and a radial probe yields extrema of −0.001 and +0.001 in near one end of a journal. At a second station the same unreset indicator shows +0.003 and +0.005 in. Each measured circle has a 0.002 in range. The two stations together already span 0.006 in from overall minimum to maximum. For an illustrative limit of 0.003 in, both sampled circles meet the circular limit, while the observations are enough to show failure of a total limit of 0.003 in. This result can arise from axial variation in size or offset. A comprehensive result requires the extent of the actual drawing and a suitably qualified measurement. An indicator on loose stock rotating in a chuck answers a setup question rather than automatically checking a drawing’s runout control.

An end face calls for a different indicator direction. If you are checking circular runout at a selected radius, hold that radius while the face rotates. A tilted but otherwise flat end face can produce axial movement in one turn. To evaluate total face runout, the measurement must also preserve the relationship between different radii. A check done only on the outer edge leaves the rest of the indicated face unevaluated.

Interpret older symbols using the drawing edition

Under ASME Y14.5-2009, concentricity can specify the positions of the median points of opposed or correspondingly located elements relative to a datum axis or center. Symmetry uses corresponding median points for its defined relationship. An ordinary runout sweep cannot establish either legacy requirement by itself. ASME Y14.5-2018 removed these symbols. A later design may choose position, runout or profile according to which geometry and function it needs to control. A manufacturing or inspection plan must follow the released callout and use the controlling edition until the product definition is changed.

ASME Y14.5-2018, Sections 11, 12 and Appendix D, and ASME Y14.5-2009, Sections 7.6.4 and 7.7.2

Test Your Knowledge

A fully constrained ASME surface profile callout reads 0.020 Ⓤ 0.006 in. Positive means added material. What signed interval applies?

A

−0.006 to +0.014 in

B

−0.010 to +0.010 in

C

−0.014 to +0.006 in

D

0 to +0.026 in

Test Your Knowledge

Marching along a journal, an indicator shows a 0.001 in spread per sampled circle. Why could the same journal fail total runout?

A

A whole-surface zone must include between-station differences as well

B

Total runout applies without a datum axis

C

A cylindrical surface is always measured with an axial probe

D

Every individual reading must be zero for circular runout

Test Your Knowledge

Which result would verify a legacy concentricity control under the stated 2009 ASME edition?

A

Any chuck runout reading below the drawing number

B

One caliper reading compared with the nominal axis

C

A visual check for two concentric circles from above

D

Evaluation of the required median points relative to the specified datum

Test Your Knowledge

What difference should guide the measurement plan for profile of a line and profile of a surface?

A

Both names always designate only the trace at one radius

B

Line profile applies in the designated sections; surface profile applies to the entire indicated surface as one entity

C

Surface profile applies only to a cylindrical shaft

D

Line profile automatically references the machine spindle

Sections you finish are checked off in the contents.