3.7 Signed Shop Arithmetic and Calculator Practice

Key Takeaways

  • Use final coordinate minus initial coordinate to find a signed move when both share the same axis, origin and units.

  • Use parentheses around signed values being squared and around the actual numerator and denominator.

  • Keep the calculated precision through intermediate steps. Apply the required reporting precision after making the dimension comparison.

Last updated: November 2026

3.7 Signed Shop Arithmetic and Calculator Practice

Set up the arithmetic before touching a key

Write down what each number represents, its units and its reference. A work coordinate can be negative because it lies on the negative side of the programmed origin; the length between two positions is nonnegative. A negative measured deviation means the measured value is smaller than the reference under the stated sign convention. It does not by itself specify which machine register to adjust.

GoalCalculationShop check
Find the directed moveFinal coordinate minus initial coordinateBoth values must use the same axis, origin and units.
Find the distance on one axisMagnitude of the directed moveUse the magnitude for length, while retaining the sign for travel.
Find departure from nominalActual reading minus nominalCompare with the allowed upper and lower deviations.
Find share per equal intervalTotal difference divided by the number of intervalsBound the first and last locations. The number of gaps can be one fewer than the number of features.

For example, a planned X move begins at −0.625 in and ends at −0.175 in. Write (−0.175)−(−0.625)=+0.450(-0.175)-(-0.625)=+0.450 in. The endpoint remains on the negative side of the origin, while the travel is toward positive X. If the tool ends at −0.900 in instead, the move from −0.625 in is −0.275 in. A sketch with an origin and arrow catches a sign error before it becomes a command. The controller's active absolute or incremental mode still determines what a program word means.

Enter the intended expression

On the Casio fx-991CW family the negative sign for a value and the subtraction operator are different inputs. In an expression such as (−2)2(-2)^2, put the negative value in parentheses. The square of a negative number is positive. The same model interprets an unparenthesized leading minus before a square as the negative of the square, so −22=−4-2^2=-4. Check the displayed expression before evaluating it. Other calculators can differ in the way they accept or display signed input.

A setup calculation compares two independently observed edge points, −1.150 and +0.430 in on a common coordinate scale, to find their midpoint. Enter ((−1.150)+0.430)/2((-1.150)+0.430)/2 and obtain −0.360 in. Confirm that each edge is 0.790 in from the result. Dividing only the second number by two violates the required grouping. If you are converting the result to metric, first determine whether the recipient needs millimeters or inches. Apply the conversion once. When reusing a stored value, check its sign, units and what it represented.

For calculations using drawing angles, verify the calculator angle setting. For example, in degrees sin(30°) = 0.5; a radian setting with the bare input 30 gives a different result. Use the known-value check before applying the mode to triangle calculations. On an instrument that can return fractions, 3/163/16 in is 0.1875 in. Convert display format without silently treating a fractional inch result as a decimal millimeter value.

Use the result to make a checkable decision

A shaft drawing calls for 0.6250 in with lower deviation −0.0010 in and upper deviation +0.0005 in. The two limits are 0.6240 in and 0.6255 in. A reading of 0.6239 in has signed deviation −0.0011 in and lies 0.0001 in below the lower limit. Keep the observation at its reported precision and follow the measurement plan for a close result. Rounding the reading to 0.624 in before the comparison hides the difference.

A row of five holes is planned between X−1.250 in and X+0.750 in at equal spacing. The directed difference is +2.000 in, and five holes define four intervals. The step is +0.500 in. The middle position is −0.250 in, and four additions return +0.750 in. Check these results with the drawing origin and the setup sheet before writing an absolute list or an incremental move. The first and last locations provide a check independent of the calculator's key sequence. Write all five positions before programming the row. The successive values are −1.250, −0.750, −0.250, +0.250 and +0.750 in. Each difference must carry the same sign, and the center should bisect the endpoints.

Casio fx-991CW calculation priority, Casio angle and display settings and the NIMS machining crosswalk

Test Your Knowledge

On the same X work scale a move begins at −0.375 in and ends at −0.925 in. What is the signed increment?

A

+0.550 in

B

−0.550 in

C

−1.300 in

D

+1.300 in

Test Your Knowledge

How should you enter the square of a signed value of −0.40 on the stated scientific calculator?

A

Use the leading minus without grouping it with the value

B

Square 0.40 and make the result negative

C

Enter the negative value in parentheses and then square it

D

Use 0.40 divided by two

Test Your Knowledge

A width is 1.250 in with allowable deviations of −0.002 in and +0.004 in. What is the lower limit?

A

1.248 in

B

1.246 in

C

1.252 in

D

1.254 in

Test Your Knowledge

Four holes are equally spaced from X−0.600 in to X+0.900 in. What is the positive step between holes?

A

0.225 in

B

0.375 in

C

0.300 in

D

0.500 in

Sections you finish are checked off in the contents.