4.6 Cutter Catalogs, Length of Cut and Extension

Key Takeaways

  • Length of cut is the functional axial cutting length. Overall length is tip to back of shank. Extension out of holder is measured on the assembled tool from the specified holder reference to the tip.

  • Separate cutter diameter from shank diameter. Use cutter diameter for feature and cutting calculations and shank diameter for toolholding.

  • Use operation-specific manufacturer data, including radial and axial engagement and entry capability. Confirm gripping length and clearance along the complete path.

Last updated: November 2026

4.6 Cutter Catalogs, Length of Cut and Extension

Translate the feature into tool requirements

Start with the current print and process plan. A flat floor, a vertical shoulder, a contoured surface and a chamfer call for different edge forms. A square-end cutter can generate a flat floor and vertical walls. A corner-radius cutter strengthens the edge when the part permits the radius. A ball nose serves contoured surfaces and can have a smaller effective cutting diameter at shallow engagement. A chamfer cutter must match the angle convention and reach. Confirm whether the quoted angle is included or measured to the axis. For entry into stock, verify the cutter maker’s plunging, ramping or predrilled-entry limits.

Read the supplier drawing for the exact part. Cutter diameter describes the cutting envelope. Shank diameter controls fit and clamping. Some cutters have larger shanks than their cutting diameter. Flute count and helix influence cutting and chip space, but the manufacturer’s application data determines the usable conditions. A familiar shape or model family alone cannot establish a supported plunge, ramp angle or chip load.

Compare the four different lengths

DimensionWhere it is measuredWhy it matters
Length of cut (LOC)Along the tool axis over the functional cutting portionMust cover the intended axial contact without rubbing the noncutting shank or neck
Overall length (OAL)Cutting tip to the back end of the toolHelps plan the assembly and available shank length
Reach or length below shankFrom the tool tip to the beginning of the full shank on a necked tool, using the supplier’s drawingA reduced neck can provide wall clearance beyond the active flutes
Extension out of holder (EOH)From the stated holder reference at the nose to the cutting tip after assemblyDetermines projection and affects rigidity and clearance; record the reference surface used

The NIMS crosswalk pairs LOC and EOH because a practical setup must check both. Even a cutter with sufficient LOC can have a holder-body collision, an unsupported extension or insufficient grip. Measure the assembly instead of treating a nominal tool drawing as the measured length. The tool length used for the control has its own reference and may include the holder. Keep it separate from EOH in the setup sheet.

Worked catalog decision

Helical tool number 01465 is an uncoated, square-end three-flute tool listed for aluminum alloys and nonferrous materials. Its catalog dimensions are 0.500 in cutter diameter, 0.500 in shank diameter, 1.250 in LOC and 3.000 in OAL. The product page provides a separate speeds and feeds resource as well as a model for checking the CAM setup.

An aluminum wall needs 0.800 in of cutting edge contact on the planned finish pass. This cutter’s 1.250 in LOC satisfies the initial axial cutting-length requirement. For this exercise the collision check requires EOH of at least 1.500 in. A trial assembly at 1.625 in EOH leaves 1.375 in of the nominal 3.000 in tool behind the holder-nose reference. This is geometric insertion past the reference. Verify how much of the straight shank actually contacts the holder’s gripping element and compare it with the manual. The actual grip can be less than 1.375 in. Check where the flute transition sits and whether the back of the tool touches anything during tightening.

If the job instead requires cutting a 1.400 in high wall in one pass, the 1.250 in LOC is short even if the tool tip can reach the bottom. Consider a different tool or a qualified sequence with shorter engagements and verified neck clearance. If the cutting length works but the tool body contacts a clamp, resolve the fixture and assembly clearance. Extending the tool affects stiffness, gripping length and the tool length value measured for the program.

Pull operating data from the exact cutter

Use the catalog row or selection tool for the actual part number and stock condition. Check operation, spindle-side or cutter-side limits where given, cutting speed, feed per tooth, axial depth and radial width. Record the units and whether tooth feed is recommended directly or determined from a chip-thickness target. For milling, use the effective number of teeth and approved speed to calculate feed. A feed for a supported light side cut can be inappropriate for a full slot. Verify entry limits and coolant guidance separately. Save the verified tool identifier and dimensions with the setup so a later substitution is checked at the same level.

NIMS extension and length terminology, Harvey end mill dimensions, Helical 01465 and Sandvik effective profile-milling diameter

Test Your Knowledge

An end mill reaches the bottom of a part but has a 1.250 in LOC. The proposed pass needs 1.400 in of continuous cutting contact on the side. What does the catalog establish?

A

The operation is acceptable if OAL exceeds 1.400 in

B

The cutting length is insufficient for that pass

C

The cutting length can be increased by selecting a longer holder

D

The operation is acceptable if radial depth is 1.400 in

Test Your Knowledge

A tool has 3.000 in OAL and 1.625 in measured EOH from the holder nose. What length lies behind that reference?

A

1.625 in

B

3.000 in

C

4.625 in

D

1.375 in, with actual grip length to be checked separately

Test Your Knowledge

The cutter diameter is 0.375 in and the straight shank diameter is 0.500 in. Which dimension determines the correct collet range?

A

The 0.500 in shank diameter

B

The 0.375 in cutter diameter

C

The average of the two diameters

D

The total flute length

Test Your Knowledge

What should you check before taking side-milling cutting data from an end mill catalog and applying it to a full slot?

A

Only that the tool has the same color

B

Only the holder’s balance grade

C

The manufacturer’s data for slotting, including engagement and entry conditions

D

Only the overall length of the cutter

Sections you finish are checked off in the contents.