4.5 Face and Peripheral Milling
Key Takeaways
On a vertical mill, face milling makes a surface perpendicular to the spindle axis. Peripheral milling uses the outside edges to produce a surface parallel to it.
Distinguish axial depth from radial engagement. When milling a wall, axial engagement is contact length along the flutes and radial engagement is the width removed in the plane of rotation.
Plan cutter centerline, approach, exit, force direction and body clearance. Prove both the top and side features against the drawing.
4.5 Face and Peripheral Milling
Let the required surface decide the cut
In face milling, the cutter axis is approximately perpendicular to the finished surface. The face mill’s entering edges remove the stock and its lower edges generate the face. An indexable shell mill on a matched arbor can cover a wide top surface efficiently. For example, a general-purpose 45° entering-angle cutter can spread the cut along the edge and direct a larger axial component of force into the part than a 90° cutter. Check how the part is supported against that component.
In peripheral milling, the outer cutting edges do the work. On a vertical mill the side of an end mill can cut a vertical edge or wall parallel to the spindle. A shoulder cutter can generate a floor and wall together, if its entering angle, insert radius and cutting length meet the print. A 45° face mill leaves an angled transition against an adjoining vertical feature, so select a tool designed for a square shoulder when that transition matters. Every actual tool has some corner form or radius to compare against the drawing.
Plan the engagements
For a top face, axial depth is the thickness removed in the spindle direction. Radial engagement is the width of material the rotating cutter engages in the plane of the cut. Consider the planned width and tool centerline together. With suitable stock and clearance, an off-center approach can produce a thinner chip at exit and avoid abrupt full-width engagement. Where there are multiple passes, select the stepover and confirm the entire face is swept without cutter-body or holder contact.
On a wall, axial engagement is the length of edge engaged along the wall, and radial engagement is the width the side cuts into the remaining stock. Changing axial depth, radial engagement or cutter path can change force and chip thickness. At light radial engagement the maximum chip thickness can be smaller than programmed feed per tooth. Use the supplier’s actual chip-thickness or feed data for that engagement, tool geometry and material. A full slot engages more of the cutter circumference than a light wall finish.
Climb (down) and conventional (up) describe feed relative to cutter rotation at the engaged side. In typical peripheral climb milling the chip starts thick and thins. Conventional milling begins at smaller thickness. Climb is often preferred on a rigid CNC setup. Confirm cutter rotation, engaged side, support and machine condition. The compensation side follows the programmed path and material side, so the word “climb” alone cannot select G41 or G42.
Plan the first-piece checks
| Process concern | Check during prove-out |
|---|---|
| Top stock varies from end to end | Check the raw height range against the allowed depth and the entry path. |
| Cutter passes between clamps | Include the rotating cutter body and the holder in the clearance envelope. |
| Floor and wall cuts use separate tools | Inspect the finished corner for the specified radius or permitted transition. |
Worked job for a top face and side wall
A print calls for a clean horizontal top and a square outside side wall. The supported blank is 1.50 in wide. For this exercise the 2.00 in nominal face mill has a checked effective swept cutting diameter of 2.00 in at the chosen depth. The clear setup permits a centerline 0.15 in toward one edge from the blank center. From that line the stock edges are 0.60 and 0.90 in away. Both are inside the 1.00 in swept cutting radius. Verify the full entry and exit path beyond the ends, including clamps, holder and cutter body. Take the specified facing allowance and measure the face height and condition. Width coverage alone proves neither clearance nor part accuracy.
Next finish the side with a peripheral cutter, removing 0.020 in radially over a 0.500 in wall height. For that pass the radial engagement is 0.020 in and the axial engagement is 0.500 in. Check the cutter’s straight cutting length, corner form, stickout and clearance below the wall before programming. Use the table row for the stated type of side cut and trial the first part at approved conditions. Compare side size at multiple heights to distinguish nearly uniform size error from a tapered wall caused by deflection or orientation. Confirm square relationship to the top with the job’s specified inspection method.
If the top shows witness tracks after a finish pass, check for an axially high insert, seating, machine tram or deflection before changing feed. If the wall varies with height, inspect setup and tool support before assuming a diameter compensation change will correct it. Record the approved assembly and any needed change to the first-piece inspection.
Sandvik face milling, shoulder and peripheral milling and inch milling formulas
A horizontal top surface and a vertical wall are separate operations on a vertical mill. Which pairing is correct?
Peripheral milling for both surfaces
Peripheral milling for the top, face milling for the wall
Face milling for the top, peripheral milling for the wall
Face milling for the wall, drilling for the top
A side finish removes 0.018 in of stock from a wall and engages the flutes over 0.625 in of height. What are its radial and axial engagements?
0.018 in radial and 0.625 in axial
0.625 in radial and 0.018 in axial
0.643 in radial and 0.625 in axial
0.018 in radial and 0.018 in axial
A cutter’s effective swept radius is 1.00 in. A rectangular blank is 1.50 in wide and a straight face-mill centerline is 0.30 in off center. What does the transverse geometry show?
Both edges are 0.75 in away
Both edges are covered because the cutter diameter exceeds stock width
The far edge is 0.95 in away
The far edge is 1.05 in away, so the sweep misses it
A process must generate a vertical wall meeting a floor at a square shoulder within the print’s corner allowance. What tool should you evaluate first?
Any 45° face mill because it can face the floor
An approved 90° shoulder cutter with a corner form that meets the print
A ball-end mill selected by overall length alone
Any shell mill with enough teeth
Sections you finish are checked off in the contents.