6.4 Orthographic Views and Drawing Lines

Key Takeaways

  • Identify the projection from the drawing. In a standard third-angle layout, the top view is above the front and the right view is to its right.

  • Use views together to distinguish external edges, features hidden from view, axes, cutting planes and features at other positions.

  • A cutting-plane line and arrows specify the slice and viewing direction. A section view can show where a bore, step or recess ends.

Last updated: November 2026

6.4 Orthographic Views and Drawing Lines

Orient the page before tracing a feature

An orthographic view shows a part along a specified direction without perspective distortion. Several views put the dimensions of one three-dimensional part on a sheet. The front view is the orientation used to relate the other principal views. Identify how the drawing indicates its projection. ASME Y14.3 addresses the creation of orthographic and pictorial views. In a standard third-angle layout, the top view sits above the front, and the right-side view sits to the right of the front. First-angle layouts place the right-side view on the opposite side. Read the indicated projection, view names and arrows before assigning a side of the actual stock.

The front view normally shows width and height in its plane. The aligned top view shares width and supplies depth. The right-side view shares height with the front and also shows depth. Cross-check features at corresponding positions instead of treating each view as a different part. If a detail or auxiliary view is displaced from the main layout, follow its label, viewing arrow or other reference. Interpret it using the declared orientation.

Match the line type to the information

Line functionTypical appearanceQuestion it answers
Visible edge or outlineContinuous prominent lineWhich edges are visible in this direction?
Hidden edgeRegular short dashesWhich edge lies behind material from this direction?
CenterlineAlternating long and short elementsWhere is the axis or center of the feature?
Dimension and extensionFine continuous lines, with terminating arrows on dimension linesWhich features and size or distance does the value concern?
LeaderLine connecting a note or callout to the relevant featureWhich feature is the note specifying?
Cutting planeDesignated prominent line with viewing arrows and identificationWhere is the section taken and which way is it viewed?
Section liningThin stroke pattern in a section viewWhich material is cut by the imaginary plane?
Phantom lineLong elements alternating with pairs of shorter onesIs this an alternate position or another indicated reference rather than a visible edge of the current part?

Follow dimensions and symbols attached to the lines. A centerline locates an axis but does not give diameter or depth. A hidden line may represent a step on the back, a blind bore or a feature in another plane. A line rendered lightly or faintly in a scan can be mistaken for a different stroke pattern. Check the other views and controlled drawing information if the interpretation affects a cut.

Work through a blind bore with a step

Consider a synthetic third-angle print of a rectangular block. The top view shows two concentric visible circles associated with a counterbore. Centerlines mark their common center. In the front view, paired hidden lines extend downward from the top to two different depths. The A–A cutting plane crosses the common hole axis. The A–A section shows that the larger diameter ends at a shoulder, and that the smaller diameter ends in the block. The local dimension note controls the diameters and depths.

A machinist can use the top view and its location dimensions to identify the entry face and XY location. The section clarifies which depth belongs to the larger recess and which belongs to the smaller bore. Even two concentric circles at the top cannot establish whether the drilling breaks through. If the viewer mistakes the hidden bottom for an invisible through opening, the drill can break through into a fixture or damage a required surface. Select tooling and a verification method after confirming the depth reference and the blind feature.

Resolve confusing geometry before making a cut

A section arrow supplies sight direction, while the section labels match the viewing instruction to the separate image. Locate the same shoulder or axis across the views and compare the dimensions. A local enlarged detail may use another scale, and an auxiliary view may reveal the true shape of an inclined face. Use reported dimensions and the controlling model or drawing rather than estimating depth from projected line lengths. If directions or notes conflict, use the drawing control process to resolve them before programming that feature.

ASME Y14.3 orthographic views, ASME Y14.2 line conventions, Haas and Autodesk projection examples and NASA GSFC illustration of line conventions

Test Your Knowledge

On a standard third-angle layout, which view is immediately to the right of the front view?

A

The top view

B

The left-side view

C

The right-side view

D

The bottom view

Test Your Knowledge

Which line shows the direction from which a cut section is seen?

A

The cutting-plane line with its arrows

B

A hidden line appearing in the section

C

An ordinary extension line from the outside dimension

D

A centerline with no section label

Test Your Knowledge

A drawing shows two concentric circles from above. Where can you most directly distinguish a blind counterbore shoulder from the bottom of the small hole?

A

A centerline in the top view alone

B

The width scale of the front view

C

The external outline of the side view alone

D

The labeled section through the hole axis and its depth callouts

Test Your Knowledge

What does a dashed hidden edge in a front view establish, by itself?

A

That the feature passes through the entire block

B

That an edge exists behind a visible surface from that direction

C

That the dashed form is the axis of a hole

D

That the line gives the direction for viewing a section

Sections you finish are checked off in the contents.