3.5 CNC Shop Safety Protocols & Operational Standards
Key Takeaways
Use shop-selected eye, foot, hearing and other personal protective equipment for the hazards identified in the job’s assessment.
Keep hands, gloves, jewelry, loose clothing and hair away from moving spindles, tools and workpieces.
Use the machine’s guards and interlocks as designed. Stop and report a failed safeguard before running the machine.
When mist or skin contact presents a hazard, use the exposure controls for the actual product, machine and task.
For hazardous servicing, verify isolation and deenergization under 29 CFR 1910.147(d)(6) before starting the work.
CNC Shop Safety: Guarding, PPE and Hazardous Energy
A CNC mill can move the table, spindle and tool changer in response to a program. A stopped cutter may leave other hazards such as coasting motion, spring force, trapped air, coolant pressure, hot chips or sharp edges. Match each task to its hazard and the control specified by the manufacturer and the shop. The regulations below are U.S. federal OSHA general-industry requirements.
Guarding and Personal Protective Equipment
OSHA’s machine-guarding rule covers exposure to the point of operation, rotating parts, and flying chips and sparks. On an enclosed machining center, the enclosure contains chip and coolant spray and restricts access. An interlock or door lock can prevent certain motions or keep a door closed. The permitted actions depend on the control, mode and job. Consult the machine instructions for setup and run modes. Keep guards and interlocks functional. If an interlock malfunctions, report it and keep the machine out of operation until the safeguard has been restored.
Personal protective equipment (PPE) is selected for the task under the employer’s hazard assessment. Use eye protection with side protection when flying objects are a hazard. Use protective footwear when stock or tooling could fall or roll onto the feet, or when other foot hazards are present. Secure loose clothing and long hair and remove jewelry that could catch. Keep gloves and hands away from rotating tools or stock. The gloves selected to handle sharp chips or liquid chemicals belong to the appropriate stopped and safeguarded task.
An eight-hour time-weighted average exposure of 85 dBA is OSHA’s hearing-conservation action level. It triggers the hearing conservation program. Employers must make protectors available at that exposure. Required use depends on conditions in 1910.95, such as exposure above the permissible limit or, at or above the action level, a worker without a baseline audiogram or with an applicable standard threshold shift. Wear the protection specified for your work area.
Chip Cleanup and Cutting Fluid
Before removing chips, stop motion and follow the shop’s safe-access procedure. Use an approved brush, hook or rake instead of grabbing sharp chips by hand. If cleaning requires removing a guard or servicing a jam where unexpected energization could injure someone, apply the relevant hazardous-energy procedure. Where a shop permits compressed air for cleaning, OSHA requires pressure reduced below 30 psi with effective chip guarding and PPE. A nozzle or regulator alone leaves chip and exposure hazards to address.
Cutting fluid may irritate skin, and mist can expose nearby workers. Keep the enclosure and mist controls functional, maintain the fluid according to the product and shop instructions, control leakage and contamination, and use the PPE specified for the cleanup or handling task. Report skin symptoms or unusual mist through the shop’s procedures. Adding concentrate beyond the target range can increase skin irritation.
If a mist-control unit fails and fluid mist leaves the enclosure, stop and report the unsafe condition through the shop procedure. Check the engineering controls and applicable hazard information before resuming. Fluid testing and adjustment are separate tasks. Section 8.3 uses a worked concentration check and distinguishes approved methods for fresh charges and working fluid.
Lockout/Tagout and Verification
OSHA 29 CFR 1910.147 applies to covered servicing when unexpected startup, energization, or release of stored energy could cause injury. Setting up, unjamming and cleaning can be servicing in that situation. Normal production is generally outside the scope. Servicing during production can be covered when the worker must bypass a safeguard or place any body part in the point of operation or an associated danger area during the operating cycle. Some minor servicing during normal production can qualify for an exception only when it is routine, repetitive and integral to production and effective alternative protection is used. An employee should follow the employer’s equipment-specific procedure and training for the task.
| Stage | Authorized employee’s responsibility |
|---|---|
| Prepare and notify | Know the sources, magnitude and hazards of energy, and notify affected employees as required. |
| Stop and isolate | Shut down in an orderly way. Operate the isolating devices identified by the procedure for all hazardous sources. |
| Apply locks or tags | Apply the employer’s lockout or tagout procedure to the energy-isolating devices. Lockout is the default when the device is lockable unless the employer demonstrates equivalent protection under the standard. |
| Control stored energy | Relieve or restrain potentially hazardous stored energy. Continue verification if it can reaccumulate to a hazardous level. |
| Verify | Verify isolation and deenergization before starting work, using the specified methods for the equipment and energy sources. |
For example, a stuck chip conveyor may have electrical power even after the control stops the conveyor, and covers or parts may move when a blockage is removed. An authorized worker verifies the isolation and deals with stored energy under the procedure before attempting to clear it. An Emergency Stop or selector switch is a control-circuit device. Electrical tests on exposed parts are performed by qualified personnel under the applicable electrical safety procedure. Before restoration, follow the release procedure, inspect the work area, ensure personnel are safely positioned, and notify affected workers as required.
Sources: OSHA machine guarding, PPE, hearing conservation, compressed air, metalworking fluids, lockout/tagout.
Why must a machinist keep gloves away from a rotating spindle or workpiece?
The fabric prevents an operator from checking setup dimensions by feel.
The rotating assembly can catch the glove and pull the hand inward.
A glove covered with cutting fluid can become slippery during handling.
A gloved hand can transfer coolant onto the part during inspection.
A mist collector stops and cutting-fluid aerosol begins escaping the enclosure. What should the operator do?
Increase coolant pressure to push the mist back into the enclosure
Raise fluid concentration without testing
Keep cutting until the smell changes
Stop and report the failed exposure control, then follow the approved procedure before resuming
Under OSHA 29 CFR 1910.147(d)(6), what does an authorized employee verify before starting hazardous servicing after lockout or tagout has been applied?
Informing the shop supervisor that the task is starting
Verify that the machine is isolated and deenergized using the applicable procedure.
Cleaning the chip conveyor and draining the coolant tank
Removing the LOTO padlocks and tags to test axis movement
The mill is stopped and the shop’s safe-access steps for routine cleaning have been completed. How should the operator remove loose, sharp chips from a fixture?
Blowing chips off with 90 PSI compressed air directed toward the operator
Wiping chips away using bare hands covered with barrier cream
Use the shop-approved chip brush or hook to move chips clear.
Sweeping chips while the spindle is turning at 100 RPM to sling chips clear
Sections you finish are checked off in the contents.