7.4 Verifying Flatness and Perpendicularity

Key Takeaways

  • Surface flatness is a feature-without-size check in the stated example. Fit the least separation of parallel planes that contains the surface points under the required method.

  • A surface perpendicularity zone has a fixed orientation to its datum. Establish the datum before scanning the controlled face.

  • For an RFS cylindrical hole perpendicularity callout, verify the required axis relationship over the controlled extent. An entry circle checks neither tilt nor the whole axis.

Last updated: November 2026

7.4 Verifying Flatness and Perpendicularity

Decide whether to use a datum

For inspection of one milled surface without a size dimension, a surface flatness tolerance applies to the entire specified face. The two parallel boundaries are free to orient to the surface. Perpendicularity instead orients the zone at 90° to a specified datum. The drawing may also impose separate thickness, location or texture requirements on the part. Identify the feature and exact control before choosing the instrument.

As with other dimensional checks, fixture force, dirt and burrs can change the measured result. Supports must hold the part safely without bending it or suppressing the feature variation being checked. Use the specified restrained or free state. Bring the part and suitable calibrated equipment to the inspection conditions. Confirm access to corners and the regions where tool marks, wear or part distortion can cause extremes.

Verify a free flatness zone

A suitable CMM with an approved evaluated-point distribution can estimate surface flatness using a minimum-zone fit. Use enough points to represent the surface, including edges and known distortion locations. The minimum-zone result is the smallest spacing between two parallel planes containing the sampled points. A least-squares plane followed by peak-to-valley is a different estimate, and three points always fit a plane even if the surface between them varies.

An indicator on a surface plate can screen for height variation. Use it for acceptance when the method has been qualified for the specified feature and tolerance. Set stable supports, a suitable indicator direction and a useful grid. A suitable orientation can reduce the contribution of arbitrary part tilt. Merely seating the opposite face on the plate and measuring vertical spread includes any tilt of the surface. Three supports define how the part rests. They do not show whether the measured surface meets flatness.

Observation for a 0.003 in flatness limitInterpretation
Simple vertical sweep range 0.005 inThe observed range includes setup orientation. Use the qualified evaluation before drawing a flatness conclusion.
Validated minimum-zone result 0.0022 in after suitable coverageThe sampled result is within the limit. Apply the inspection plan’s decision rule and uncertainty requirements.
One high region near a burrReview the prescribed surface preparation and feature extent. Do not discard real surface data simply to reduce the result.

Verify perpendicularity to a plane

Consider an upright face specified as perpendicular to datum plane A within 0.003 in. Establish A through the applicable simulation in the approved method. For a surface-plate and square method, seat the datum feature as required, and establish the 90° reference with a qualified fixture or master square. Move the indicator in a path referenced to that orientation, with the probe sensitive normal to the controlled face. Measure over the designated face or grid and preserve the common reference. A check at one vertical line can miss variation across the face.

For a simple, already aligned measurement, verified minimum and maximum deviations normal to the vertical zone are −0.001 in and +0.0015 in. The span is 0.0025 in. Compare the full span to 0.003 in using the inspection decision rule. A square used only to see light under a part can be a setup aid. Producing a documented result requires suitable resolution, coverage and datum realization for the tolerance.

On a first piece, a sweep may be stable with light seating but change after a fixture clamp is applied. Check whether the drawing specifies restrained measurement and whether the approved fixture reproduces it. If the approved method uses a free-state part, change the support rather than using the load to improve the reading. For a datum-oriented check, also verify the square or fixture reference before attributing the change to the part.

If the controlled feature is a cylindrical hole with an RFS perpendicularity diameter, the zone applies to the relevant axis across the controlled length. A CMM with enough accessible data can evaluate that relationship after establishing datum A. Plan sampling at more than one depth and use the fitting method required for the callout. A loose pin tilted in the bore or a single circle at the mouth gives incomplete evidence. A separate hole-size or MMC surface boundary check may require a different plan.

ASME Y14.5-2018, Sections 8 and 9, NIST flatness inspection plans and NIST analysis of fitting methods

Test Your Knowledge

Three non-collinear points lie in one plane. What is still needed to evaluate a machined face’s flatness?

A

Only the thickness of the plate

B

Representative data across the controlled face and the specified form evaluation

C

A datum plane named in the flatness frame

D

Only the nominal orientation of the face

Test Your Knowledge

An approved datum-oriented surface perpendicularity check shows deviations of −0.0008 in to +0.0020 in. What span applies?

A

0.0012 in

B

0.0020 in

C

0.0008 in

D

0.0028 in

Test Your Knowledge

A reading range was taken with a tilted part simply resting on its opposite face. What could that range include?

A

Rigid-body tilt of the inspected face in addition to form variation

B

Only local diameter error

C

Only perpendicularity of the bore axis

D

The material-boundary modifier of the datum

Test Your Knowledge

Which check addresses the perpendicularity of a bore axis at RFS rather than just its mouth?

A

One diameter with a two-point indicator at the opening

B

A depth gage that touches the bottom once

C

An appropriate bore-axis evaluation over its length relative to the established datum plane

D

A wipe test to check surface cleanliness only

Sections you finish are checked off in the contents.