3.3 Cutting Speeds (SFM), Feeds (IPM/IPT), RPM, & Machining Calculations
Key Takeaways
In inch units, spindle RPM is (12 × SFM) ÷ (π × effective cutting diameter in inches).
Milling table feed is RPM × feed per tooth × number of effective cutting teeth.
Turning linear feed in inches per minute is RPM × inches per revolution. Haas lathe G99 selects feed per revolution.
In steady rectangular milling engagement, width of cut × depth of cut × table feed gives volume removed per unit time.
Metric cutting calculations convert cutting speed (Vc in m/min) to RPM using the formula RPM = (1000 * Vc) / (pi * D_mm).
Cutting Speeds (SFM), Feeds (IPM/IPT), RPM, & Machining Calculations
Cutting speed, spindle speed and table feed describe different motions. The cutting speed tells you how fast the active cutting edge passes the material. Revolutions per minute (RPM) describe spindle rotation, while table feed describes linear advance along the programmed path. Choose the starting cutting speed and feed per tooth from data for the specific tool, work material and cut. Then convert them to the numbers that belong in the mill program.
Choosing Inputs
Surface feet per minute (SFM) and meters per minute are two units for cutting speed. For many cylindrical end mills cutting on the periphery, the nominal tool diameter is the effective diameter. On a ball-nose tool at shallow axial depth, the contact diameter can be smaller than the nominal tool diameter. Read the manufacturer’s effective-diameter guidance for the tool. In turning, use the diameter defined by the supplier’s cutting calculation.
Check the tool supplier’s unit system and the job’s spindle, feed, holder and workholding limits. The exercises give input values to practice the arithmetic. Actual cutting data vary with engagement, tool geometry, cutting fluid, material condition and machine limits.
Spindle RPM Formulas
To translate linear surface speed (SFM) into rotational spindle speed (RPM) for effective cutting diameter in inches:
Where:
- converts feet to inches.
- .
- .
Metric RPM Formula:
For cutting speed (m/min) and tool/workpiece diameter (in millimeters):
Feed Rate Formulas (IPM, IPT, & IPR)
Feed rate governs the linear travel speed of the machine table or lathe carriage.
Milling Feed Rate (Inches Per Minute - IPM)
In milling, feed rate depends on spindle RPM, feed per tooth (IPT), and effective cutting teeth ():
Turning Feed Rate (IPM vs. IPR)
In a supplemental Haas lathe example, G99 selects feed per revolution and G98 selects feed per minute. Those same codes select cycle return heights on a Haas mill. Multiply the per-revolution feed by actual RPM to compute linear feed:
Metal Removal Rate (MRR)
Metal Removal Rate (MRR) quantifies the volume of material removed per unit of time, expressed in cubic inches per minute () or cubic centimeters per minute ().
Milling MRR Formula:
Where:
- .
- .
- .
Supplemental Turning MRR Estimate:
This is the turning estimate in inch units using the cutting-speed convention of the calculation. Cutting depth is radial, so a 0.125-in depth removes 0.250 in from the diameter in an external pass. For milling with dimensions in mm and table feed in mm/min, width × depth × feed gives mm³/min. Divide by 1,000 to express the result in cm³/min.
Step-by-Step Worked Calculation Examples
Worked Example 1: Aluminum Milling
Problem: A machinist is profiling 6061-T6 aluminum using a 0.500-inch diameter 3-flute carbide end mill. Exercise inputs: 500 SFM, chip load 0.003 in/tooth, axial depth of cut 0.250 inches, radial width of cut 0.200 inches. Calculate the required Spindle RPM, Table Feed Rate (IPM), and Metal Removal Rate (MRR).
-
Step 1: Calculate Spindle RPM
-
Step 2: Calculate Feed Rate (IPM)
-
Step 3: Calculate Metal Removal Rate (MRR)
Worked Example 2: Alloy Steel Turning
Problem: A CNC lathe turns a pass to a 3.000-inch machined diameter of 4140 alloy steel using a coated carbide insert at 350 SFM and 0.012 in/rev (IPR) feed rate. Depth of cut is 0.125 inches. Calculate spindle RPM, linear carriage feed, and estimated material removal rate.
-
Step 1: Calculate Spindle RPM
-
Step 2: Calculate Carriage Feed Rate (IPM)
-
Step 3: Calculate Volumetric MRR
Worked Example 3: Metric End Milling
Problem: A 12 mm diameter 4-flute end mill cuts steel at with programmed feed per tooth . Calculate Spindle RPM and Feed Rate in mm/min.
-
Step 1: Calculate RPM
-
Step 2: Calculate Feed Rate ()
Retain extra digits until you decide which RPM to program, then calculate feed using the selected RPM. Check that the answer is plausible. At the same cutting speed, a larger effective diameter needs fewer revolutions per minute. At the same RPM and feed per tooth, increasing the number of effective cutting teeth increases the programmed table feed.
Sources: Sandvik Coromant milling formulas, Sandvik Coromant turning formulas, and Haas lathe G-code list.
What is the calculated spindle speed (RPM) for a 0.750-inch diameter end mill cutting medium carbon steel at a surface speed of 150 SFM? (Use pi = 3.1416)
764 RPM
955 RPM
1,200 RPM
510 RPM
A four-flute end mill with four effective cutting teeth runs at 2,400 RPM and 36.0 in/min. What is its programmed feed per tooth?
0.0025 inches
0.00375 inches
0.0050 inches
0.0150 inches
A CNC milling operation uses a 0.500-inch width of cut (WOC), a 0.200-inch depth of cut (DOC), and a feed rate of 30.0 IPM. What is the Metal Removal Rate (MRR)?
1.50 in³/min
6.00 in³/min
3.00 in³/min
12.00 in³/min
When converting a metric cutting speed of Vc = 120 m/min for a 20 mm cutter to spindle RPM, which calculation correctly yields the operating RPM?
RPM = (120 * 20) / 1000 = 2.4 RPM
RPM = (120 * 3.1416) / 20 = 18.8 RPM
RPM = (3.82 * 120) / 20 = 22.9 RPM
RPM = (1000 * 120) / (3.1416 * 20) = 1,910 RPM
Sections you finish are checked off in the contents.