6.2 Form and Orientation Tolerances
Key Takeaways
ASME Y14.5-2018 uses 12 geometric characteristic symbols across form, orientation, profile, position and runout.
Form controls apply independently of a datum. Circularity applies separately to circular elements, while cylindricity applies to the whole cylindrical surface in one zone.
Orientation sets the angle of the tolerance zone relative to the specified datum. Read the attachment and zone symbol to identify what must fit.
For a sine bar on one level surface, the required rise under one roller is the center distance times the sine of the intended angle.
6.2 Form and Orientation Tolerances
Identify the controlled geometry and zone
Use the standard invoked by the drawing. ASME Y14.5-2018, reaffirmed in 2024, lists 12 geometric characteristic symbols. The form and orientation controls below are the starting point for part shape and angle; other sections explain position, profile and runout. Appendix D identifies the deletion of the concentricity and symmetry symbols from the 2018 edition. An older drawing can still invoke the edition that defines its symbols.
| Family | Characteristic and symbol cue | Typical controlled geometry or zone |
|---|---|---|
| Form | Straightness, straight stroke | Two parallel lines for a surface element; a cylindrical zone for a derived median line with a diameter designation |
| Form | Flatness, parallelogram | Two parallel planes for the designated surface or derived median plane |
| Form | Circularity, circle | Two concentric circles at the considered circular element |
| Form | Cylindricity, circle with slanting side strokes | Two coaxial cylinders containing the considered cylindrical surface |
| Orientation | Parallelism, parallel strokes | Zone oriented parallel to the datum |
| Orientation | Perpendicularity, right-angle symbol | Zone oriented 90° to the datum |
| Orientation | Angularity, angle symbol | Zone oriented to the datum at a specified basic angle |
| Profile | Profile of a line, arc | Zone about designated line elements |
| Profile | Profile of a surface, arc on a baseline | Zone about the indicated surface |
| Position | Position, target-like symbol | Common examples use a diametrical zone for a hole axis or parallel planes for a slot’s center plane, subject to the exact callout |
| Runout | Circular runout, single diagonal arrow | A separate zone for each considered circular element about the datum axis |
| Runout | Total runout, double diagonal arrow | One zone for the entire indicated surface about the datum axis |
Section 6.1 shows how to read the frame. Match the graphic symbol, callout attachment and any diameter mark or modifiers to the feature under inspection. A position specification can relate features to each other without locating them to a separate datum. Profile may use datum references when the drawing requires a relationship.
Study the form cases
For surface flatness, the specified separation is the total distance between parallel planes that must contain the surface. They can orient to suit the surface. A plate can have a flat top that is tilted relative to its bottom. Flatness alone leaves that orientation uncontrolled. When flatness is applied to a width feature’s size dimension for the derived median plane, the controlled geometry corresponds to midpoints between the opposed surfaces. Read the connection to the surface or size requirement.
For straightness of a surface element, use two parallel lines in the specified section. For the separate derived-median-line application, a diametrical zone can contain the line of local centers of a cylindrical feature. Inspect the line the drawing controls. An indicator trace down one external generator does not determine the derived median line.
Circularity of a cylindrical surface can be viewed in sections transverse to the axis. Each considered circular element must fit between concentric circles separated radially by the stated tolerance. Cylindricity places the full surface between two coaxial cylinders with that radial separation. An ideal tapered surface can have round sections at every height and still fail a cylindricity limit because one full-length zone cannot contain it. Neither form callout uses a separate datum.
Study the orientation cases
An orientation tolerance relates the controlled feature to the datum reference. For example, a surface perpendicularity zone consists of two parallel planes, separated by the stated tolerance, oriented 90° to the referenced plane. The zone’s location can vary within the limits of other drawing requirements. The same characteristic on a hole’s size callout with a diameter designation defines a cylindrical zone for evaluation of the axis; its ideal direction is perpendicular to the referenced plane. If specified at MMC or LMC, the corresponding surface boundary also matters. Section 7.4 gives practical verification decisions for the surface and hole cases.
Surface parallelism uses planes oriented parallel to the datum. Surface angularity sets those planes at the specified basic angle. The tolerance value is a distance across the zone. A basic 30° angle with a tolerance of 0.004 in calls for a linear zone oriented at 30°, rather than a plus/minus interval of 0.004 degrees.
Set a reference angle before measuring
A sine bar offers one way to orient a suitable wedge. With one roller on the plate and the other on a gage-block stack, use the specified roller center distance . The right triangle gives . At in and , the required stack is 2.5000 in. Seat and secure the actual datum face in the intended direction, check cleanliness and block seating, and use a suitable indicator and sampling plan on the surface. The sine-bar setup establishes nominal orientation. The observed variation still depends on the datum seating, tool uncertainty and points measured.
ASME Y14.5-2018, Sections 6.4 and 8–12, and Starrett sine bar
Which callout controls shape while letting the zone orient independently of the named part datums?
A surface parallelism tolerance
A total runout tolerance
A surface flatness tolerance
A surface angularity tolerance
A 5.000 in sine bar has one roller on the plate. What stack under the other roller establishes 30°?
2.5000 in
4.3301 in
2.8868 in
10.0000 in
A feature has round cross-sections at every height but tapers enough that it does not fit between the specified coaxial cylinders. Which statement follows?
It fails both controls because every circular element has the same center
It can satisfy circularity and fail cylindricity
It satisfies both controls because each cross-section is round
It fails circularity but satisfies cylindricity
An RFS perpendicularity frame on a cylindrical hole shows a diameter symbol before 0.004 and references plane A. What does the 0.004 establish?
Width of an angular zone from 89.996° to 90.004°
Distance between the hole and plane A
Radial width of the circularity zone at a single station
Diameter of a cylindrical zone oriented perpendicular to plane A
Sections you finish are checked off in the contents.