5.1 Milling Workholding Devices
Key Takeaways
Use a vise for compatible stock and fixture-specific locators/supports when shape, cutting loads or access demand them.
Jaw pull-down helps minimize lift. Verify that the work actually seats and use the approved preload procedure when making soft jaws.
For a strap supported at the work and heel, moving the stud toward the work increases the work-end share of stud force.
Vacuum holding depends on pressure difference, sealed area and friction. Magnetic fixtures require suitable magnetic material and contact conditions.
5.1 Milling Workholding Devices
Choose by reference, force and tool access
First identify the workpiece features used for seating and location. Then identify the likely cutting reactions and the path of the cutter and holder. An arrangement that grips securely during a face cut can interfere with a through-hole drill or let a slender wall deflect in a side cut. Check the supports, stop faces, fasteners and tool path together.
| System | Good starting application | Verify before use |
|---|---|---|
| Machine vise with hard jaws | Prismatic stock with adequate parallel gripping area | Jaw opening, grip height, support below part and tool/holder clearance |
| Vise with machinable soft jaws | Irregular sides, a finished surface or a second-operation form | Load path, contact pattern, screws, cut limits and repeatability on actual parts |
| Dovetail holding | Multi-face access on compatible prepared stock | Model drawing, remaining section, engagement, torque and rotary clearance |
| Subplate, modular or quick-change fixture | Repeated workholding changeovers and parts with distributed locators | Clean receiver interfaces, locked shanks, hardware loading and verified position |
| Strap or low-profile edge clamp | Large or low work requiring direct mounting | Fully seated contacts, supporting rests, stops and clear cutter path |
| Vacuum or magnetic fixture | Suitable plate with restricted clamp access | Compliant material, contact and load limits for the actual device |
Jaw pull-down and custom jaws
The Kurt DX6 Anglock design uses a spherical segment and geometry that produces a downward component as the movable jaw advances. Kurt describes a nominal half unit of downward force per unit of forward force for that design. It reduces the tendency of the movable jaw to lift. Part seating still depends on jaw condition, available grip, stock and supports. Check the stock against its parallels or fixture rests after final tightening.
Soft jaws provide machinable contact areas. Aluminum is common, and some manufacturers also offer machinable steel. Follow the actual jaw maker’s method and protected cutting boundary. For example, Kurt’s PF Series instructions call for precision blocks below the cut and the intended production tightening torque while preparing the carvable jaws. Clamping at a representative load accounts for the deflection and position of the jaw system under that load. It gives a better chance of obtaining the intended loaded fit. Confirm that the reliefs clear fasteners and workpiece corner burrs, and prove the finished fit by loading a representative part. Check grip, location and part size when released.
Dovetail holding can expose more faces while it grips a prepared region of the blank. Kurt’s DoveLock catalog shows the exact cutter and stock-preparation geometry for its models. Use that geometry and clamp setting rather than applying a depth or angle from a different product. Ensure the planned cuts leave the holding feature intact until the part transfers to another setup.
For modular fixtures, distinguish plate location from workpiece location. Jergens Ball Lock uses locating shanks and matched bushings to locate a fixture plate to a subplate. Additional hold-downs can support load without creating additional locating interfaces. After a plate change, verify the seating, the locating reference for the work and any change to the work offset.
Strap clamp leverage
For a simple rigid strap with its work contact and heel seated, suppose a vertical stud force acts between the contacts. Neglect strap weight. If the work contact is from the heel and the stud is from the heel, moment balance about the heel gives the downward work-end force . The heel carries the remaining share. For example, with in, in and a known 800 lbf stud force, the part sees 600 lbf and the heel sees 200 lbf in this model. Moving the stud toward the supported work end while keeping it within the approved range can increase the part’s share. Stud torque by itself does not supply the actual tension in this model.
Select a heel support that lets both contacts seat as intended by the clamp design. Check the step engagement, T-slot hardware, washer seating, clearance and rigid support under the work. Follow the manufacturer's instructions for strap angle, loading and fastener tightening. A low-profile toe clamp can open up tool access at the top and may act downward and inward. Confirm that its force is directed toward the appropriate supports and stops.
Vacuum and magnetic plates
For a sealed vacuum fixture, the ideal normal force is pressure difference times effective area inside the seal. A 100 in² sealed area with a maintained 12 psi difference yields 1,200 lbf normal force in that model. If a verified interface friction coefficient is 0.25, the simple sliding estimate is 300 lbf without stops. It cannot qualify a cut by itself. Verify seal and vacuum monitoring during the entire path, especially before machining through the sealed area. Coolant, texture, leakage, uplift and overturning can reduce practical resistance. Designed stops can help carry horizontal loads if compatible with clearance.
An approved magnetic milling chuck grips suitable ferromagnetic materials. Thickness, pole coverage, surface contact and air gap affect holding force. Some electropermanent designs, such as SCHUNK MAGNOS milling chucks, need electrical power to switch the state. Compatible pole extensions can improve access. Verify magnetized state and the application limits before machining.
Kurt DX6, Kurt PF series, Kurt DoveLock catalog, Carr Lane fixturing, Jergens Ball Lock, Schmalz vacuum clamping and SCHUNK magnetic milling
Why does the Kurt DX6 mechanism tend to reduce movable-jaw lift?
A spring opens the jaw once the work is seated
Its clamping geometry generates a downward component as the jaw advances
A wider jaw automatically centers both sides of the stock
Its base keys apply the clamping force to the parallels
Why does the Kurt PF procedure use a clamped precision block when machining carvable jaws?
The block replaces a grip check on the production part
It allows machining through the protected boundary
It allows the jaw pocket to be machined with the jaw system under representative clamping load
It gives a fixed repeatability regardless of setup
The stud of an ideal strap clamp applies 1,000 lbf downward, 3 in from the heel. The work contact is 5 in from the heel. What downward force reaches the work?
600 lbf
400 lbf
1,000 lbf
1,667 lbf
A fixture maintains 10 psi differential over 60 in². Assume a verified friction coefficient of 0.30, no stops and a pure sliding model. What lateral resistance does the model give?
60 lbf
200 lbf
600 lbf
180 lbf
Sections you finish are checked off in the contents.