3.12 Hazard Communication, HMIS and Safety Data Sheets

Key Takeaways

  • Identify the exact product and find its safety data sheet before deciding on use, storage or response.

  • Read the HMIS workplace label with the shop’s training and current product hazard information. The label is one part of the communication system.

  • The federal immediate-use exception is limited to the transfer employee who controls and uses the material in the same shift.

Last updated: November 2026

3.12 Hazard Communication, HMIS and Safety Data Sheets

Read the product before starting the task

A machinist may encounter concentrates, cleaners, lubricants and other products with similar packaging but different hazards. Check the product identifier on the container against the job instruction and the safety data sheet (SDS). Federal OSHA Hazard Communication, 29 CFR 1910.1200, requires covered workplaces to communicate hazards through its program, labels, SDSs and training. The workplace method should tell workers how to recognize products, understand the precautions and obtain details during the shift. If a chemical arrives in a damaged or unidentified container, preserve the separation and follow the shop's procedure to identify it before use.

Labels on shipped hazardous chemical containers generally identify the product, signal word, hazard and precautionary statements, relevant pictograms and responsible-party contact information under paragraph (f)(1), subject to applicable exceptions. OSHA allows a workplace label method under paragraph (f)(6). A workplace label can use the shipped-label elements or use the product identifier plus markings that, together with immediately available information, convey the specific physical and health hazards. Follow the employer's implemented system and keep incoming labels legible.

The American Coatings Association's Hazardous Materials Identification System (HMIS) is one possible workplace tool. Its blue band addresses health, red flammability, orange physical hazard, and white the system's PPE designation. Its numerical hazard ratings go from 0 to 4 with higher values indicating greater severity for that band. A health asterisk indicates a chronic hazard in this system. Interpret any letter or mark with the shop's HMIS training and PPE chart. Do not copy an OSHA hazard-category number onto an HMIS band as if the two scales were interchangeable. Ask the designated person to resolve discrepancies before using the material.

Find the SDS sections that answer the question

Shop questionSDS location to consult
Is this the product and use from the job plan?Section 1, identification, including use information and supplier or emergency contact.
What hazards have been identified?Section 2, hazard identification.
What needs immediate first aid?Section 4, first-aid measures.
What extinguishing and spill response considerations apply?Sections 5 and 6, fire and accidental release. Read them with the site emergency plan.
What storage, exposure controls and PPE are relevant?Sections 7 and 8, handling/storage and exposure controls/personal protection.
What incompatibilities or dangerous reactions need review?Section 10, stability and reactivity.

Electronic SDS access can satisfy OSHA's requirement when workers can obtain the information immediately and without barriers during the shift in the work area. Appendix D standardizes the SDS headings and mandatory information, with a different federal status for section content in Sections 12–15. Use available disposal guidance as a source lead and follow the site's waste determination and routing process. A product SDS describes the product; the actual spent stream may contain other hazards.

Apply the portable-container rule to the task

A worker transfers a small amount of hazardous cleaner from a labeled bottle into a portable container. When that worker alone keeps control and uses it within the same shift, paragraph (f)(8) provides the immediate-use labeling exception. Consider what changes if the crew wants to hand the container to another worker or keep it for the next shift. The original exception no longer fits. Use the approved workplace labeling process before the change, or return the material through the approved procedure. An informal abbreviation that other workers cannot identify is inadequate.

If a new coolant concentrate replaces the earlier one, match the identifier to its own SDS, check handling and exposure controls, and verify training for a new chemical hazard where applicable. For a splash-related task, the site hazard assessment and applicable SDS guide appropriate protection. Additional demands may arise from the mixture process itself. A familiar white PPE band on an old HMIS label is insufficient evidence for the new product or task. If the operator has a workplace label but the product name differs from the SDS listing, verify whether the names identify the same product before proceeding. Preserve access to both the label and the current safety information.

OSHA 1910.1200, OSHA SDS Appendix D, OSHA HMIS guidance and American Coatings Association HMIS training

Test Your Knowledge

A worker transfers hazardous cleaner from its labeled bottle, then leaves the portable container for the next shift. What is required under the stated conditions?

A

Apply the workplace labeling procedure because the immediate-use exception no longer fits

B

Leave it unlabeled because a portable container always qualifies

C

Write only the time of transfer on the lid

D

Rely on the fact that the original bottle is still labeled

Test Your Knowledge

A new concentrate replaces an older one. Which SDS section addresses exposure controls and protective equipment?

A

Section 1

B

Section 5

C

Section 8

D

Section 16

Test Your Knowledge

An HMIS health block shows an asterisk. What does this mark signal under the stated system?

A

An unverified physical hazard rating

B

Evidence of a chronic health hazard

C

An automatic exemption from exposure controls

D

A particular glove material for every task

Test Your Knowledge

A second-shift worker cannot access the electronic SDS until a manager returns the next day. What must the shop address?

A

Only the date printed on the workstation

B

Only the manufacturer’s phone number in the purchasing system

C

Only the hazard rating on the used-oil container

D

The access barrier that prevents immediate availability during that shift

Sections you finish are checked off in the contents.