7.2 Phonetic Alphabet, Number Formatting & Train Descriptions

Key Takeaways

  • Use the phonetic alphabet for signal and points identities, train descriptions, difficult or confusable names, and when communication is affected by interference.

  • Speak separate digits for identifiers, including the zero in numbers such as 104. Handbook 1 recognises exceptions, including time and Rule Book module and handbook numbers.

  • Transmit a line name and the actual location reference. An Up or Down designation must be taken from the applicable route information.

  • One mile is 80 chains. Keep the miles and chains separate when passing a location and have the listener check the whole reference.

Last updated: November 2026

Spell what the receiver needs to identify

A signal prefix, a point number or a train description can differ from another valid identifier by a single character. RSSB Handbook 1 Issue 9, sections 9.1 and 9.5 sets out the phonetic alphabet for track workers. Use it when identifying letters, when quoting signal and points identities or train descriptions, and to spell place names or words that are difficult to say or could be misunderstood. Use it when interference affects a phone or radio call. A phonetic word refers to the letter, so substitute it for that letter rather than guessing what a prefix stands for.

LetterWordLetterWord
AAlphaNNovember
BBravoOOscar
CCharliePPapa
DDeltaQQuebec
EEchoRRomeo
FFoxtrotSSierra
GGolfTTango
HHotelUUniform
IIndiaVVictor
JJulietWWhisky
KKiloXX-ray
LLimaYYankee
MMikeZZulu

For example, if one person hears the prefix TB and the other says DB, asking only to repeat the digits will not resolve the difference. Spell the full relevant identifier and repeat back the location. The aim is to identify the same asset, including when two nearby lines use similar identifiers.

Pass digits separately and recognise the exceptions

When passing a number such as a signal number, say each digit separately. Signal DM104 is Delta Mike one zero four. The zero matters because it distinguishes 104 from 14. When quoting a train description such as 2E45, say two Echo four five. The letter is identified by its phonetic word. The number is not grouped as forty-five. The rule is about what is transmitted, not an instruction to infer the train's route, permitted speed, or whether a train has cleared the site from the description alone.

Handbook 1 gives numbers such as a time or a Rule Book handbook or module reference as exceptions to the general digit rule. “Handbook seven” is an ordinary reference to the book. In a planned call, confirm that time references clearly refer to the same part of the day and the same event, such as the earliest grant time or the expected time for giving up the blockage. An ambiguous time cannot be repaired by pronouncing it more loudly. The receiver should clarify and repeat back the agreed limits and timing.

Give the location as well as the identifier

Use the line's actual designation. Do not infer the meaning of Up or Down from the direction towards London or the direction in which a train happened to pass. Line designations, current route information and an asset identifier help distinguish parallel lines at the same mileage. The Network Rail Safety Central glossary gives 80 chains to a mile and approximately 20.12 metres per chain. A location recorded as 52 miles 40 chains is spoken as five two miles, four zero chains. Forty chains is half a mile, but retain the miles and chains stated in the actual location reference so it can be checked against the site's records.

ReferenceSpoken example
Signal WH209Signal Whisky Hotel two zero nine
Train 1A23Train one Alpha two three
Points 204APoints two zero four Alpha
Down Fast at 52 miles 40 chainsDown Fast, five two miles, four zero chains

Worked example: a transposed number

During a call to arrange a blockage on the Down Fast, the COSS reads the two boundaries from the NR3180 form. The signaller reads the second back as Delta Mike two six zero. The COSS checks the record and repeats the Down Fast boundary as Delta Mike two zero six, then asks the signaller to read back the line and both limits. If the COSS had actually said the wrong number, the Rule Book phrase Correction signals that the COSS is replacing what they just said. In either case, listen for the corrected identifier within the whole repeat-back.

If both people can repeat the digits but still disagree about where the boundary lies, keep the group clear and verify the reference against the applicable route information with the signaller. Agreeing the line and both boundaries establishes which limits the call refers to. Under Handbook 8, wait until the required arrangements are in place and the signaller gives the authority number. Record it on NR3180 before treating the blockage as granted.

Loading diagram...
Examples of Phonetic Letters and Individual Digits
Test Your Knowledge

How should the train description 2E45 be transmitted under the Handbook 1 rules for track workers?

A

Twenty East forty-five

B

Two Es forty-five

C

Two Echo forty-five

D

Two Echo four five

Test Your Knowledge

Which spoken identifier should the COSS use for signal WH209?

A

Whisky Hotel two zero nine

B

Whisky Hotel twenty-nine

C

William Harry two zero nine

D

Whisky Hotel two hundred and nine

Test Your Knowledge

The COSS reports Down Fast, 39 miles 15 chains. The receiver swaps miles and chains on the read-back. Which full reference should the COSS restate before asking for another read-back?

A

Down Fast, thirty-nine miles fifteen chains

B

Outward line, three nine miles one five chains

C

Down Fast, three nine miles one five chains

D

Down Fast, three nine chains one five miles

Sections you finish are checked off in the contents.