6.2 Sighting Distance & Warning Time Calculations

Key Takeaways

  • For group lookout warning, add five seconds per additional direction the site lookout watches, not per track crossed. Reaching safety must not require crossing an open line.

  • The warning time includes stopping work and putting tools down safely, reaching the position of safety, and a minimum of ten seconds already in safety before the train arrives.

  • Use the applicable Handbook 7 sighting chart for the maximum speed and warning time. A speed-times-time estimate is not the operational chart value.

  • More than 45 seconds needed, inadequate sighting, or a permissible approach speed above 25 mph rules out lookout warning even if the remaining conditions pass.

Last updated: November 2026

Check eligibility before calculating

The lookout rules apply to a planned group Safe System of Work using lookout warning. On Network Rail that arrangement requires a Controller of Site Safety with the separate COSS (LKT) competence. See RSSB Handbook 7 Issue 10, section 6.8 and the sighting charts. Check all the conditions before relying on a calculated distance. A train on a 30 mph approach rules out human lookout warning even if the view is clear for a long distance. The same is true if anyone would have to cross an open line to reach safety. A safe position that requires more than 25 metres of walking along the line is also outside the group lookout rule.

Lookout warning is only an option if no alternative safe system can be used and its use was planned in advance and authorised at director level. The COSS does not act as a lookout for the group. Consider how trains are routed as well as where they may be visible: approaches must be on the line of work or an adjacent line, and a train must not be able to change onto the line the group is on or near after the lookout has seen it.

Work out the whole interval

Start with the time to stop work and put tools down safely. Use a time that reflects the actual task and the arrangement for equipment. Then account for how long it takes everyone to reach the position of safety. A fitter close to the cess is not the right measure if the last person has farther to go or must navigate uneven ballast. Handbook 7 requires tools and equipment to go to safety unless they are too heavy to be moved by the slipstream and are left clear of the line. Include the time needed for the agreed way of making them safe.

For each additional direction a site lookout must watch, add five seconds. A lookout watching both directions on one bidirectional line therefore adds five seconds even though there are no open lines to cross on the route to safety. If a person cannot reach safety without crossing an open line, no time increment can make this arrangement acceptable.

Finally, add ten seconds already in the position of safety before a train reaches the site. This is distinct from the total time from the warning. If the whole warning time needed is more than 45 seconds, lookout warning cannot be used. The handbook's worksheet has a separate entry for lone working; do not use that entry as a group calculation or transfer this group arrangement to lone working.

Translate time into an operational sighting distance

Select the maximum speed for the approach from the Sectional Appendix using the correct location, line and direction. Read the required distance from the applicable Handbook 7 chart. The calculation of how far a train travels in that time helps explain why faster approaches need more distance. For instance, at 25 mph a train covers about 11.18 metres a second, or about 279 metres in 25 seconds. The Rule Book chart for that speed and time gives 280 metres. Other chart entries are not uniformly the arithmetic distance rounded up to a fixed number of metres, so use the chart for the operational value rather than making your own rounding rule.

Maximum approach speedTotal time neededSighting distance from the Issue 10 mph chart
20 mph25 seconds240 metres
25 mph25 seconds280 metres
25 mph30 seconds340 metres

Issue 10 includes chart entries above 25 mph for reference when equipment warning is used. Their presence does not authorise lookout warning at those speeds. Equipment warning has its own conditions.

Worked example: a bidirectional approach

Suppose the other authorisation and task conditions hold at a 25 mph site. The group can reach a position of safety within the walking limit without crossing any open line. Its slowest person needs four seconds to stop and put tools down safely, then six seconds to reach safety. One site lookout must watch both directions. The required time is 4 + 6 + 5 + 10 = 25 seconds. The mph chart gives 280 metres. One direction has a clear 310 metre sightline; the other has only 260 metres because of a curve. The shorter sightline fails. The available distance in one direction does not compensate for a shortfall in the other.

Do not use an intermediate lookout to relay a warning around the curve. Keep the group in safety and change to an approved, suitable arrangement, which may involve blocking the line. Even if both approaches could be seen in time, you would still need to test the warning and brief the group before starting. If an obstruction later hides a required approach, the lookout gives the warning and informs the COSS. Darkness, poor visibility, or a location in or near a tunnel rules out lookout warning.

Loading diagram...
Eligibility, Warning Time and Sighting
Test Your Knowledge

In a group lookout arrangement under Handbook 7, how long must everyone already be in the position of safety before the train arrives?

A

5 seconds

B

20 seconds

C

15 seconds

D

At least 10 seconds

Test Your Knowledge

At an otherwise eligible 25 mph site, a group needs four seconds to stop and put down tools and six seconds to reach safety. A site lookout watches two directions. How much warning time does the group need?

A

25 seconds

B

20 seconds

C

30 seconds

D

15 seconds

Test Your Knowledge

A planned lookout arrangement needs 25 seconds at 25 mph. The Issue 10 mph chart gives 280 metres, but the lookout can see only 260 metres on one approach. What is the safe decision?

A

Use the longer sightline on the other approach as a substitute

B

Keep the group in safety and arrange another approved safe system

C

Post an intermediate lookout to relay the warning

D

Reduce the warning time to fit the distance by dropping the extra direction allowance

Sections you finish are checked off in the contents.