9.1 Immediate Emergency Protection: Detonator Placement & Distances
Key Takeaways
RSSB Handbook 2 Issue 2 applies to trained track workers providing emergency protection. Try to contact the signaller as quickly as possible.
Full detonator protection under section 4.1 applies if the signaller cannot be contacted: three detonators 20 metres apart on each affected line at 2 km in the direction of approach.
If a train approaches before the full-protection point, show the hand danger signal and place three detonators immediately only if it is safe to do so.
An available track-circuit operating clip is an immediate measure except where there is a fourth rail. Its use does not confirm the signaller has protected the line.
Reporting danger and providing protection
A landslip, displaced load or derailed vehicle can make one or more lines unsafe. Do not rely on the boundaries of an existing safe system to protect a newly affected line. Get the group clear of danger and report the hazard immediately. Give the exact location and affected lines and make it clear that the information needs immediate action. RSSB Handbook 1 Issue 9, sections 6 and 8 covers reporting and stopping trains in an emergency. The separate RSSB Handbook 2 Issue 2 instructions apply to track workers trained to carry out emergency protection. Do not interpret a COSS title alone as authority to direct an untrained worker to place detonators.
First actions for a worker trained under Handbook 2
Section 4.1 concerns a line that is obstructed or unsafe. If available, put a track-circuit operating clip on each affected line, except where there is a fourth rail. Try to contact the signaller as quickly as possible. A clip is equipment that operates a track circuit via the two running rails. It is not a universal train detection device and fitting it does not tell you the line has been protected. In a third-rail area, put the clip on the running rail farthest from the conductor rail first. Do not reuse a clip. Once fitted, obtain the signaller's permission before removing it and apply the requirements for resuming normal working or replacement protection.
If the signaller cannot be contacted, go towards the direction from which trains can approach to provide full detonator protection. Under section 4.1, that means three detonators 20 metres apart on each line concerned at 2 kilometres (approximately 1¼ miles). Display a hand danger signal to an approaching train on the affected line. This is a prescribed emergency protection arrangement; it does not guarantee a stopping distance for every train.
Do not use damaged or deteriorated detonators or those manufactured more than five years ago. Handbook 2 gives a general instruction to use the farther running rail if possible in a third-rail area. Where Handbook 17 Issue 6, section 4.1 applies, it requires placing them on the running rail farthest from the conductor rail. Check the applicable rules for the actual infrastructure. When positioning them at a signal, place the first beside it and the other two beyond it. If staying near detonators that are not at a signal, stand at least 30 metres beyond them so the driver can see the hand signal after the train reaches the detonators. After giving full protection, stay near the detonators and continue giving the hand danger signal unless told otherwise. Do not remove emergency protection until the line is safe again or you are told to do so because other protection is being provided.
Changes on the way to full protection
Handbook 2, sections 4.2 to 4.5 gives instructions for events that can change what you do before reaching the full-protection distance.
| Event before reaching the full-protection point | Action under Handbook 2 |
|---|---|
| A train approaches on the affected line | Display the hand danger signal. Place three detonators immediately only if safe to do so. |
| You reach a telephone linked to the signal box or reach the signal box | Place three detonators on the affected line and speak to the signaller. If they confirm the line is protected, there is no need to continue to 2 km. |
| You reach a signal fitted with a signal-post replacement switch | Operate the switch before placing the three detonators, then speak to the signaller. |
| You reach a tunnel | Place three detonators at the entrance. Take care for your own safety and continue to the full-protection location; if that point is inside the tunnel, put the detonators at the far end. |
| You reach a junction | Place three detonators before it and consider which line to protect next based on where a train is most likely to approach. |
Give the hand danger signal clearly
In daylight, show a red flag. Without one, raise both arms above your head. If riding on a vehicle, the daylight signal is one arm held out horizontally. In darkness or poor visibility show a red light or wave any light violently. The worker must make the signal visible to the driver. The type of hand signal depends on the conditions, not the mileage at which it is given.
Scenario: a blocked line and a train appearing early
A wall collapses onto a running line. The COSS gets the group clear, reports the precise location and tries to reach the signaller. Assume the worker undertaking protection is trained, the signaller cannot be reached and the worker sees a train before reaching the planned point for full protection. The worker gives the hand danger signal. If it is unsafe to place detonators now, they do not step into danger to complete the placement. The question asks what changes once the train appears: the worker must warn the approaching driver and the early placement is subject to safety. The 2 km figure applies to full protection and is not a reason to wait before warning an approaching driver.
A trained track worker must provide full detonator protection for an obstructed line under Handbook 2 section 4.1 because the signaller cannot be contacted. What does full protection require?
Three detonators 20 metres apart at 2 km on the approach to the obstruction
Three detonators 20 metres apart immediately beside the obstruction
Two detonators at 2 km on different running rails
One detonator at the nearest signal, wherever it is
Which condition prevents using an otherwise available track-circuit operating clip when a trained worker protects an unsafe line under Handbook 2?
The signalbox phone is busy
The line has a third rail
The line has a fourth rail
The unsafe condition is an obstruction rather than a track defect
A train approaches before a trained worker reaches the full-protection point. It is unsafe to place detonators immediately. What should the worker do?
Keep going towards the 2 km point before warning the driver
Show the hand danger signal without stepping into danger to place detonators
Place all three detonators even though this is unsafe
Wait to see if the train slows without a warning
Sections you finish are checked off in the contents.