9.4 P&ID Interpretation & Loop Documentation
Key Takeaways
A piping and instrumentation diagram shows functional relationships. A loop sheet shows point-to-point signal and wiring details.
Read instrument tags, location symbols and line styles using the governing drawing conventions and the project legend.
Trace the same tag through the instrument index, loop sheet, installation detail and physical location drawings.
Use isometrics and dimensioned orthographic views to determine piping direction and elevations before laying out an instrument connection.
The loop drawing and device documentation establish the signal-shield connection. Enclosure bonding has a separate protective function.
Pick the drawing that answers the question
NCCER’s instrumentation curriculum distinguishes recognition of drawing types, symbols and abbreviations (module 12107) from interpreting drawings for installation (12202). A technician may use several drawings for the same instrument. Start with the approved revision, title block, legend and sheet references. Record a discrepancy between the drawing and field installation through the site's drawing-control process.
| Document | Question it helps answer | Information to trace |
|---|---|---|
| Process flow diagram (PFD) | What happens to the process stream? | Main equipment, major streams and direction of flow |
| Piping and instrumentation diagram (P&ID) | Which equipment, valves, measuring points and control functions are connected? | Line and equipment identifiers, instrument tags, and functional connections |
| Instrument index and data sheet | Which instrument is this, and what service and range were specified? | Instrument tag, service description, document references and device specifications |
| Loop diagram or loop sheet | Where does this wire, terminal or signal go? | Device terminals, cable and pair identifiers, junction box terminals and receiving channel |
| Installation detail or hookup | How is the instrument physically attached and connected? | Brackets, manifolds, fittings, tubing arrangement and installation notes |
| Isometric and orthographic drawings | Which way does the run go, and where are the elevations and dimensions? | Pipe routing, connection points, view orientation and written dimensions |
The International Society of Automation (ISA) publishes ANSI/ISA-5.1-2024 for instrument and control symbols and identification. A tag usually conveys a measured variable and a function, with modifiers where required. Location and shared-control symbols convey additional information. Confirm how the project applies these conventions in its legend and drawing notes.
Trace a pressure measurement
A training drawing uses PDT-305 for a differential pressure transmitter. Its tag legend uses P for pressure, D as the differential modifier and T for transmitter. The number 305 identifies the loop on these sheets. The P&ID shows taps on either side of a filter and one transmitter. Its legend distinguishes solid process connections from dashed electrical signal lines. The two process connections carry the upstream and downstream pressures to the transmitter. The signal line carries the measured differential to the control system.
Start with the tagged instrument. Follow its process lines to verify which tap supplies the high port and which supplies the low port. Then follow the signal line toward the control system. If the line continues to another sheet, match the connector reference and sheet identifier. A single dashed line on this drawing identifies a signal type through the legend. To find the precise wire and terminals, use the loop sheet.
Read the loop sheet before moving a wire
In this example the approved loop sheet shows cable C-305 from PDT-305 to junction box JB-12. The positive conductor lands on TB1-07, and the return conductor lands on TB1-08. A multicore cable continues from the junction box to analog input channel AI-16 at the cabinet. Match the cable, pair number, terminal and polarity at each transition. If the transmitter behaves correctly locally but AI-16 shows no signal, the terminal references let you divide the problem into field device, field cable, junction box, multicore and cabinet sections.
The loop drawing places the shield’s earth termination at the power-supply end and specifies insulation at the transmitter. The Rosemount 3051 reference manual describes a single earth termination at the power-supply end for its signal shield, with the transmitter-end shield insulated from the case. It gives separate enclosure-grounding instructions. This arrangement addresses a particular measurement circuit. Other wiring can have different termination requirements. For example, Siemens’ PROFIBUS installation guidance describes earthing cable shields at both ends within its equipotential-bonding arrangement. Keep the shield termination, signal return and protective enclosure bonding distinct.
Locate the installation
An isometric depicts routing and direction changes in a single three-dimensional-looking view. Orthographic views project the object onto planes, such as a plan (top) view and an elevation (side) view. Use their dimensions and elevations, since schematic lengths and angles can be illustrative. If the isometric shows the outlet above the inlet, check the stated elevations before deciding how far the tube rises.
For example, the plan view puts a pressure tap 24 inches east of the proposed stand. The elevation view puts the tap centerline at 60 inches and the transmitter centerline at 48 inches relative to the same datum. The tap is 12 inches above the transmitter. Check the hookup for routing and support requirements, then fit the run using the approved dimensions and the bender's actual take-up. The loop sheet can locate conductors at a terminal, while the installation and location documents establish where the field assembly goes.
Sources checked November 16, 2026. Department of Energy engineering drawings handbook, ABB control documentation example, Emerson Rosemount 3051 reference manual, Figure 4-3.
In the training P&ID legend, P denotes pressure, D denotes differential and T denotes transmitter. What does PDT-305 identify?
Pressure dump timer in loop 305
Pneumatic device transducer in loop 305
Differential pressure transmitter in loop 305
Positive displacement totalizer in loop 305
The P&ID shows PDT-305 sending a measurement to the control system. Which document identifies the exact junction box terminals and analog input channel?
Instrument loop sheet
Process flow diagram
Pipe isometric
Instrument stand fabrication detail
The tap centerline dimension is 60 inches and the transmitter centerline is 48 inches, both measured from the same datum. What does the elevation view establish?
The wire run is 12 inches long
The tap is 12 inches above the transmitter
The transmitter is 12 inches above the tap
The complete tube cut length is exactly 12 inches
Sections you finish are checked off in the contents.
You've completed this section
Continue exploring other exams