9.1 Instrumentation Safety, Electrical Work & Lockout/Tagout
Key Takeaways
Identify electrical supplies, process pressure, instrument air and stored mechanical force before servicing a valve or transmitter.
A DCS command or stop pushbutton is a control device. Use the designated physical energy-isolating devices for lockout or tagout.
After applying energy controls, address hazardous residual energy and verify isolation before starting work.
A qualified person verifies electrical restart prevention and tests exposed circuit parts for voltage, including backfeed and induced voltage.
Inspect tools and test leads, use equipment suited to the task, and check the safety data sheet before handling hazardous chemicals.
Identify the sources before servicing the instrument
A control valve can have a 24 V control signal, instrument air and process pressure. The actuator can also contain a loaded spring. A stop command to the controller can leave every one of those energy sources available. Before work, trace the supply, process connection and actuator on the applicable drawings. Match each hazard to its actual means of isolation and use the equipment-specific energy-control procedure.
This section uses federal Occupational Safety and Health Administration (OSHA) rules for general industry. In covered machine servicing where unexpected startup or stored energy could injure someone, 29 CFR 1910.147 governs hazardous-energy control. Exposure to electrical hazards at electric-utilization installations is addressed under Subpart S, including 29 CFR 1910.333. Instrument work may expose a technician to hazards addressed by both provisions. Construction work has separate requirements, including 29 CFR 1926.417 for electrical circuits.
Apply and verify the energy controls
Under 1910.147, an authorized employee applies the energy controls for servicing. An affected employee operates or uses the equipment, or works in the area where servicing takes place. Notify affected employees before applying controls and after removing them.
| Phase | What to establish | Example at a control valve |
|---|---|---|
| Prepare | Identify the energy sources, their hazards and the means used to control them. | Identify the air supply, process connections, electric supply and actuator spring. |
| Stop | Use the established orderly shutdown procedure. | Coordinate taking the loop out of service with operations. |
| Isolate | Operate the physical devices that separate equipment from the energy sources. | Identify the specified disconnects and process or air isolating devices. |
| Apply controls | The authorized employee applies the required lockout or tagout devices to the isolating devices. | Secure the designated isolation points under the equipment procedure. |
| Control stored energy | Make residual energy safe by relieving or restraining it using the prescribed means. | Address trapped pressure and stored actuator force. |
| Verify | Check that the isolation and deenergization actually work before servicing. | Use the verification methods in the equipment procedure and continue to verify if energy can reaccumulate to a hazardous level. |
A stop pushbutton, selector switch or software interlock is a control device. An energy-isolating device physically interrupts or blocks the energy path. For example, putting a distributed control system (DCS) loop in manual can help coordinate a shutdown. Physical isolation still needs the designated devices.
A tag warns people against operating the device. A lock physically holds the device in position. Under 1910.147, use lockout where the isolating device can be locked unless the employer shows that the tagout program gives equivalent protection. Use the documented arrangement for group work and shift transfer. Plan restoration too. Check equipment condition and the work area, confirm people are safely positioned, follow the authorized removal procedure and notify affected employees in the required order.
Verify electrical deenergization where exposure is possible
OSHA generally requires deenergization of exposed live parts before employees work on or near them. Exceptions include a demonstrated increase in hazards, infeasibility due to design or operational limits, and certain parts below 50 volts to ground if exposure to electrical burns or explosion from arcs does not increase. Follow the work practices required for the actual exposure. A qualified person must verify that the equipment cannot restart and use test equipment on the parts to which employees will be exposed. The test must also detect hazardous voltage from backfeed or induction. For circuits over 600 V nominal, OSHA explicitly requires a functional check of the test equipment immediately before and after that test.
Consider the terminals of a locked-out variable-frequency drive. Its screen can go dark while the DC link still holds stored energy. Follow the manufacturer's discharge instructions and the employer’s verification procedure. The qualified person must verify restart prevention and test the parts to be exposed. Hours of waiting or a dark screen cannot establish the actual voltage at a terminal.
Under 29 CFR 1910.334(c), only qualified persons may perform electrical testing. Inspect test instruments and accessories for damage before use. Select the instrument and leads for the circuit and the environment. 29 CFR 1910.335 addresses protective equipment and safeguards when electrical hazards are present. Shock involves current through the body. Arc flash involves energy released by an electrical arc. The employer’s work practices and hazard assessment guide the protections for the task. NFPA 70E is a separate electrical safety consensus standard. NFPA lists the 2027 edition as effective May 6, 2026.
Inspect the tools and materials
Remove damaged tools or test leads from use. Secure the workpiece and use the tool and guarding intended for the task. For example, supported tubing is easier to cut squarely, while a loose tube can turn or catch. Before using a cleaner, read its label and safety data sheet (SDS) for hazards, safe handling and exposure controls. A product used to clean metal on a bench may require ventilation or different protection when used in a cabinet. The OSHA references include tool condition, guarding and hazard communication.
Sources checked November 16, 2026.
An electro-pneumatic valve is stopped from the control room for servicing. What is still necessary before the authorized employee opens the assembly?
Leave the DCS in manual and open the assembly as soon as the indication stops changing.
Use the equipment procedure to isolate the identified sources, apply controls, make stored energy safe and verify isolation.
Disconnect the 4–20 mA signal only and use the valve position as proof of isolation.
Place a warning note on the workstation and verify there are no active alarms.
A qualified person is about to work on exposed parts beyond a locked-out general-industry drive disconnect. What does OSHA require before treating the parts as deenergized?
Verify that the drive display is dark and then skip electrical testing.
Read the controller’s output status and confirm it reports stopped.
Verify restart prevention and use suitable test equipment on the exposed parts, checking for voltage from backfeed or induction.
Touch only one insulated cable with a non-contact indicator and begin if it is silent.
What must the authorized employee do when stored pressure can reaccumulate to a hazardous level while a machine is being serviced?
Continue verifying isolation until the work is complete or hazardous reaccumulation is no longer possible.
Check pressure once at the start and rely on the initial reading.
Reset a controller alarm and continue as long as it remains quiet.
Remove the lock to keep the remote operator informed of pressure changes.
Sections you finish are checked off in the contents.