9.2 Hazardous Location Classification and Equipment Markings

Key Takeaways

  • Use the approved area classification and confirm its boundaries at the installation point.

  • Class I covers gas and vapor hazards. Classes II and III address combustible dust and ignitible fibers or flyings, with their own Division criteria.

  • Zone classifications use the governing conditions for presence and duration. Material group and the certification system are separate parts of the marking.

  • Check the equipment temperature rating at the actual ambient and process conditions, along with the group, protection method and approval.

Last updated: November 2026

Hazardous Location Classification and Equipment Markings

At an installation point, read the approved area-classification drawing and equipment approval before selecting or connecting an instrument. The classification describes the atmosphere and the likelihood that an ignitible quantity can be present. It depends on release sources, ventilation, material and boundaries. A solvent name or an industry label alone cannot establish the classified area or its extent.

Recognize ignition hazards

For a gas or vapor, the lower and upper flammable limits describe the concentration range that can propagate a flame under the specified test conditions. A rich gas can pass through that range as it mixes with air. A liquid's flash point describes when it gives off enough vapor to ignite in the specified test. Autoignition temperature concerns ignition without a spark or flame under the specified test conditions. Minimum ignition energy measures the energy needed to ignite a mixture under its test conditions. The project uses approved material property data and the governing classification method. In US general industry, OSHA's flammable-liquid rule defines its own four categories through 199.4 °F (93 °C), with boiling point also used to distinguish Categories 1 and 2.

Distinguish Class, Division and material group

ClassMaterialExamples of Division criteria
IFlammable gases or vapors, including vapors released from liquidsDivision 1 covers ignitible concentrations in normal operation, frequent release during maintenance or leaks, and specified simultaneous release and electrical failure scenarios. Division 2 includes releases from normally closed equipment only by abnormal operation or rupture, qualifying ventilation failures or adjacency.
IICombustible dustConsider suspended dust, conductive dust, failure and ignition conditions, and accumulations that affect equipment cooling or can ignite.
IIIEasily ignitible fibers or flyingsDivision 1 includes manufacturing or using materials that produce the flyings. Division 2 includes storing or handling the fibers outside manufacture.

29 CFR 1910.399 gives the US general-industry definitions. Article 500 and the relevant installation articles of the adopted NEC handle the Class and Division system. The more detailed material group narrows equipment selection. Typical Class I Division examples are A acetylene, B hydrogen, C ethylene, and D propane. Maximum experimental safe gap (MESG) and minimum igniting current ratio are properties used in grouping certain gas atmospheres. The letter by itself gives no approval for a different group. For Class II, typical examples are Group E combustible metal dust, Group F carbonaceous dust, and Group G flour or grain dust. Confirm the actual material and group in the classification documentation and use the applicable provisions of NFPA 497 or NFPA 499 in that design.

Read Zones on their own terms

NEC classificationTypical ignitible atmosphere condition
Article 505 Zone 0Gas or vapor is present continuously or for long periods.
Article 505 Zone 1Gas or vapor is likely to occur in normal operation. The definition also covers specified maintenance, failure and adjacency cases.
Article 505 Zone 2Gas or vapor is unlikely in normal operation and, if it occurs, usually persists for a short time. Check the other applicable criteria for the installation.
Article 506 Zones 20, 21, 22Zone classifications for combustible dusts or ignitible fibers or flyings. Presence of a combustible dust cloud is continuous, long or frequent in Zone 20, likely occasionally in normal operation in Zone 21, and unlikely in normal operation and short if it occurs in Zone 22.

Group IIA (for example propane), IIB (ethylene), and IIC (hydrogen or acetylene) are gas groups used in the Zone system. Typical Group III material labels distinguish IIIA combustible flyings, IIIB nonconductive dust and IIIC conductive dust. Read the listed system and marking as a whole. The zoning determination uses the governing definitions and assessment of the process, release and ventilation. A Division number does not convert directly into a Zone. 29 CFR 1910.307 gives the US general-industry Class I alternative and specifies Division classification for Class II and III. Check the separately applicable adopted wiring code and authority for an Article 506 design. In an IEC design, IEC 60079-10-2 assesses dust clouds and dust layers separately.

Check equipment temperature and complete approval

Common gas temperature classTemperature limit
T1450 °C
T2300 °C
T3200 °C
T4135 °C
T5100 °C
T685 °C

Some US Division markings have intermediate values such as T3C at 160 °C. Check the marked ambient range, protection method, group, permitted process heating and any special conditions. OSHA's Division marking provision uses a 40 °C ambient basis unless the equipment is marked for the applicable range and includes specified marking exceptions. It limits the marked temperature to the ignition temperature of the gas or vapor encountered. A project specification may require a lower limit. In a dust service, consider both dust layers and clouds and follow the applicable installation method and equipment limits.

For example, an approved site specification requires 150 °C or cooler and Class I, Division 2, Group C coverage at an ambient of 60 °C. A device's T4 rating is within the temperature limit if its approval assigns T4 at that ambient and under the specified process conditions. A T3C device allows 160 °C and fails this site temperature criterion. Before installation, check that the instrument approval covers the required group and location and that the wiring and mounting match the approval. The UL marking examples show why one label can include separate US Division, US Zone and other certification lines.

Test Your Knowledge

A documented area-classification study uses the Class I Division system. It finds ignitible propane can escape from normally closed process equipment only during abnormal operation or accidental rupture. The study establishes the mounting point within that classified boundary. Which marking matches the stated area?

A

Class I, Division 1, Group A

B

Class II, Division 1, Group G

C

Class I, Division 2, Group D

D

Class III, Division 2, Group E

Test Your Knowledge

An installation drawing specifies Class I, Division 1, Group B for a hydrogen gas area. Which equipment group marking should the technician verify before accepting a proposed device?

A

An approval that explicitly covers Group B in the specified Class and Division.

B

Group A alone, because the first letter in the sequence always includes the later groups.

C

Group D alone, because all gas groups use the same approval.

D

Group E alone, because hydrogen is a combustible gas.

Test Your Knowledge

A project limits equipment temperature to 150 °C at a Class I, Division 2, Group C measurement point. The four proposed devices have the required location/group approvals and the following temperature markings at the actual ambient and process conditions. Which meets the stated temperature criterion?

A

T3 (200 °C)

B

T4 (135 °C)

C

T3C (160 °C)

D

T2 (300 °C)

Sections you finish are checked off in the contents.