1.6 Receiving, Inspection, Handling & Storage
Key Takeaways
Match the instrument, tube and fittings to the purchase order, tag, material specification and documentation required for the project.
Check sensor range, pressure rating, electrical output and connection together when accepting a replacement transmitter.
Hold damaged, contaminated or unidentified items for disposition before releasing them to the job.
Support and protect stored material and keep its identity traceable through installation.
Verify the shipment before releasing it
NCCER module 12304 covers receiving, inspecting, handling and storing instrumentation materials. The receiving decision asks whether the items delivered are the items approved for this installation, whether they are in usable condition, and whether the documentation required for the project is complete. Use the purchase order, approved instrument data sheet, material specification and packing list together. Appearance and box count tell you little about a transmitter’s output option or a tube's material.
| Check | Transmitter example | Tubing and fittings example |
|---|---|---|
| Identity | Match the tag, model/options and serial number where required. | Match material marking or traceability, size, wall and joint type. |
| Application | Check sensor range, installed configuration, pressure limits, wetted parts, required output and any certification. | Check the approved tubing/fitting combination, pressure and temperature limits, and cleanliness class. |
| Condition | Inspect packaging, exposed surfaces, process threads and protective covers. | Inspect ends, bends and sealing areas for dents, scratches, dirt and distortion. |
| Documentation | Match requested calibration, compliance or test records to the item. | Verify material or lot documentation when required before splitting bundles or kits. |
A pressure transmitter with a matching faceplate display can have a different sensor span, output option or pressure limit. The Rosemount 3051 data sheet separates output and sensor configuration from pressure limits and model options. Read the approved device specification and compare the delivered nameplate and documents with it. An adjustable range in the configuration menu cannot resolve an unsuitable sensor or an incompatible electrical output.
If a part fails a check, identify what failed, segregate or hold it under the site procedure, and obtain disposition. For example, a bundle with missing material identification can look identical to an accepted bundle. Cutting and mixing it with accepted stock can make later traceability harder. Resolve identification or replacement first. Where the OSHA Process Safety Management rule applies, 29 CFR 1910.119(j)(6) addresses suitability of equipment and spares and inspection of installation against design and manufacturer instructions. Follow project rules for the actual receiving record.
Prevent damage while moving parts
Handle a transmitter and remote seal assembly so its weight is supported by the approved surfaces. Avoid pulling the assembly by a capillary, leads or a threaded process connection. Protect seal faces from tools, straps and other equipment. For example, Emerson’s 9195 wedge meter manual explains why the capillary cannot be used as a lifting point for the remote-seal assembly. Before removing a shipping cover, check when the equipment procedure authorizes exposing the surface and where the hardware will be stored. If the cover is a shipping protector, identify any specified operational plug or connection separately at installation.
For straight tubing, use an adequate rack and remove lengths without dragging them on rough surfaces. The Swagelok tubing data sheet discusses protecting the finish from scratches. A damaged tube end can interfere with the fitting seat or ferrule seal even when the rest of the tube is intact. Check the intended insertion area under good light before cutting or fitting. Store similar stock so the trade sizes, wall specifications and cleanliness classes remain distinct.
Plan stable, clean storage
In a US general-industry workplace, 29 CFR 1910.176 addresses material storage and clear aisles. Bundles, containers and tiers must be arranged so they remain stable. A loose stack of long tubing can shift or roll when a single length is pulled. Use the assigned rack or blocks, and preserve access to move the material without crossing the work area with an unsupported end.
Keep approved caps, plugs and packaging on stored components as the equipment requires. For example, parts shipped in a special clean bag with capped end connections retain their status through controlled storage and handling. The Swagelok SC-11 document describes this protection. Open such packages only under the approved job conditions. Segregate accepted clean components from oily or damaged parts. Keep identification attached to the stock, or transfer it to the cut piece or its controlled record as the project requires.
Worked receiving decision
The purchase order calls for a transmitter with a 4–20 mA output and a specified pressure rating. The delivered box label shows the right tag. The actual model code indicates a digital-only communication option. Log the discrepancy and hold that item. The tag links the transmitter to the intended service, but it does not show that the delivered option can operate with the intended input. The work package can proceed with the correct device once the mismatch is resolved.
Sources checked November 16, 2026. NCCER module 12304, OSHA materials handling, Swagelok tubing and handling data, Emerson 3051 model and performance data.
A transmitter’s shipping label has the right tag, but its model code indicates the wrong output. What is the proper receiving decision?
Install it because the tag matches.
Ignore the output code and use the housing as identification.
Use it as a permanent substitute if its display works.
Hold the unit for resolution and compare its model options with the approved instrument data.
What is the best way to protect long lengths of spare instrument tubing in storage?
Remove end protection and lean all lengths against a walkway.
Use a stable assigned rack, protect the ends and surfaces, and keep the material identification.
Stack loose lengths where they are easy to roll out.
Combine all nominally similar tubes in one unmarked bundle.
The packing list matches the order, but a tube bundle has damage at its ends and no required material tag. What is the next action?
Hold the bundle and record the damage and missing traceability until disposition.
Cut off the visible damage and install it without identification.
Assume the packing list proves the composition of every loose piece.
Mix it with approved stock before notifying receiving.
Sections you finish are checked off in the contents.