3.4 Velocity, Mass & Volumetric Flow Technologies

Key Takeaways

  • A magnetic meter uses voltage induced in a conductive moving liquid. Check model conductivity limits, full-pipe installation and process reference.

  • A Coriolis sensor measures mass flow from flow-induced tube motion and infers density from vibration frequency. Check pressure, temperature and multiphase effects for the sensor.

  • Vortex and transit-time meters infer velocity or operating volume. Converting operating volume to mass or reference volume needs the appropriate fluid data.

  • Use the meter’s pulse factor and the right time units to convert a pulse train to flow and total volume.

Last updated: November 2026

Identify the quantity and its units

A volumetric flow rate QQ is volume per time, such as gpm or m³/s. For a full pipe it equals mean axial velocity times internal pipe area. Mass flow rate m˙\dot m is mass per time, such as kg/s. If the fluid density is known under the same conditions as QQ, then m˙=ρQ\dot m=\rho Q. For a gas, volume at line conditions and volume at stated reference conditions can differ. Check what the tag and totalizer represent before comparing values.

Magnetic flowmeters

In a simplified electromagnetic measurement, a conductive liquid moving through a perpendicular magnetic field BB induces voltage E=BvℓE=Bv\ell, where vv is velocity and ℓ\ell is the effective distance between the electrodes. The meter relates electrode voltage to flow using its geometry and calibration. See the Promag measuring principle. A full-bore lined meter has no rotor or central obstruction. Installation and piping transitions can still have hydraulic loss.

The liquid must meet the conductivity requirement of the chosen meter. For example the Rosemount 8750W data sheet specifies at least 50 µS/cm and describes separate limits for reference-electrode configurations. Check liner and electrode compatibility with temperature, corrosion and abrasion. Verify that electrodes remain wetted and that the installed process reference matches the pipe and fluid. The manufacturer lists grounding straps, rings, lining protectors and reference electrodes for different arrangements. Low conductivity, a partially filled pipe or poor reference can cause unstable measurements.

Coriolis mass and density meters

In a dual-tube Coriolis sensor, a drive makes the tubes oscillate. Flow-induced inertia twists the moving tube sections and changes the relative phase of the inlet and outlet pickup signals. The calibrated timing difference represents mass flow rate, including its direction where supported. At no flow the flow-induced difference is zero in the ideal model. A real measurement uses the installed meter’s zero and calibration. See the Promass E technical information.

Density comes from a separate feature of the vibration. In a simple spring–mass model the natural frequency is fn=12πkmf_n=\frac{1}{2\pi}\sqrt{\frac{k}{m}}, with stiffness kk and vibrating mass mm. With fixed geometry and stiffness, denser fluid increases the mass and lowers the resonant frequency. An integral temperature sensor can correct for the effect of temperature on tube properties. The meter can also provide line volume by dividing measured mass flow by density where the configuration supports it. Direct mass measurement avoids needing a separate density input for the basic mass measurement. Pressure effects, vibration, installation zero and entrained gas can still affect performance. See Micro Motion’s pressure-effect note and ELITE specifications for two-phase effects.

Vortex flowmeters

A shedder bar produces alternating vortices. A sensor detects the frequency of the resulting fluctuations. The ideal relation is f=St v/df=St\,v/d, where StSt is the applicable Strouhal number and dd is the shedder’s characteristic width. In the rated region, the calibrated frequency can be used to find operating volume flow. At low Reynolds number or small signal, the relationship or detection can deteriorate. Use the installed model’s size, range and correction rather than a single Reynolds cutoff for all meters.

For steam mass flow, multiply operating volume rate by the appropriate steam density. Verify steam condition and the temperature or pressure information used in the density calculation. The Yokogawa VY manual gives separate calculations for operating volume, reference volume and mass. For example, 40 m³/h with density 2.5 kg/m³ at those conditions gives 100 kg/h.

Acoustic transit time and Doppler shift

With transit-time measurement, pulses traverse the fluid in both directions. In a simple uniform path of length LL at angle θ\theta to the axial flow, the with-flow and against-flow times are td=L/(c+vcos⁡θ)t_d=L/(c+v\cos\theta) and tu=L/(c−vcos⁡θ)t_u=L/(c-v\cos\theta). The FLOWSIC100 documentation derives

v=L2cos⁡θ(1td−1tu).v=\frac{L}{2\cos\theta}\left(\frac{1}{t_d}-\frac{1}{t_u}\right).

Sound speed cancels from this ideal reciprocal-time expression. Actual pipe geometry, acoustic coupling, attenuation, temperature-dependent properties and flow profile still matter. Stable acoustic transmission is required. Some products tolerate a limited amount of gas or suspended solids, as shown for Badger’s TFX-5000.

A Doppler flowmeter transmits sound and uses the frequency shift of returns from moving particles or bubbles. For an ideal beam with a shared transmit/receive path and reflector speed much less than the sound speed, the shift magnitude is ∣Δf∣≈2f0∣vbeam∣/c|\Delta f|\approx2f_0|v_{beam}|/c, where f0f_0 is the emitted frequency and vbeamv_{beam} is the reflector’s velocity component along the beam. See NOAA’s acoustic derivation. If the reflectors travel with the liquid, the shift can indicate velocity in the conditions the instrument supports. The Badger DFX example is intended for aerated liquids or liquids containing suspended reflectors. Check that the returned signal is adequate for the product and that it represents the intended flow. Clamp-on designs do not put a sensor body in the pipe bore.

Turbine pulse conversion and other mechanical meters

A turbine meter’s rotor turns as fluid flows through it. A pickup can produce a pulse train from blade passage. If the calibration gives KK in pulses per gallon, total volume is pulse count divided by KK. With pulse frequency ff in pulses per second, f/Kf/K gives gallons per second. Use the calibrated factor and the units configured for that output. In an example with K=120K=120 pulses/gal and f=360f=360 Hz, flow is 3 gal/s or 180 gpm. At a steady rate for 600 seconds, the input accumulates 216,000 pulses or 1,800 gallons. Check whether a transmitter has already rescaled the pulse output. Viscosity, wear and disturbed flow can affect the calibration. Straight run and filtration requirements depend on the sensor and service. See the Blancett 1100 documentation.

A positive-displacement oval gear meter repeatedly traps and transfers known increments of volume. Rotations or resulting pulses indicate total volume. A vertical Yokogawa RAMC variable-area meter has a float that rises in a tapered passage as the fluid flows upward. At equilibrium the float’s weight balances buoyancy and the force from the flow. The scale relates its position to flow for the stated fluid and conditions.

Service clueCandidateCheck before selection
Conductive liquid, room for full-bore spoolMagneticConductivity, liner/electrodes, pipe fill and reference
Mass flow required at actual conditionsCoriolisModel range, pressure effect, fluid phase and pressure loss
Steam line needs operating volume or massVortexVelocity range, installation geometry and density compensation
Available external pipe access, suitable acoustic pathClamp-on transit time or DopplerAcoustic transmission or moving reflectors for the selected method
Flow totalizer receives turbine pulsesTurbineCalibrated pulse factor, actual output scaling and permitted fluid and piping
Test Your Knowledge

A Rosemount 8750W configuration has a 50 µS/cm minimum liquid conductivity. Which measured service fails that requirement?

A

Process water at 120 µS/cm.

B

Wastewater at 350 µS/cm.

C

A hydrocarbon stream with measured conductivity of 0.10 µS/cm.

D

A water-based slurry at 550 µS/cm.

Test Your Knowledge

Which two measured features of a dual-tube Coriolis meter represent mass flow and density?

A

Flow-induced timing difference between pickups for mass flow, and tube vibration frequency for density.

B

Pressure drop through a restriction for mass flow, and an ultrasonic transit time for density.

C

The voltage between electrodes for mass flow, and liquid conductivity for density.

D

Rotor pulse frequency for mass flow, and gamma attenuation for density.

Test Your Knowledge

A turbine meter’s calibrated K-factor is 120 pulses/gal under the stated conditions. Its totalizer receives 360 pulses/s for 10 minutes with no pulse rescaling. What are the flow and total?

A

3.0 gpm and 30 gal.

B

18.0 gpm and 180 gal.

C

60.0 gpm and 600 gal.

D

180 gpm and 1,800 gal.

Sections you finish are checked off in the contents.