1.5 Lubricants, Sealants, Cutting Fluids & Cleaners
Key Takeaways
A lubricant, cutting fluid, sealant and cleaner serve different purposes in instrument work.
Match compound, location and quantity to both the equipment procedure and product instructions.
A specified bolt torque depends on the specified assembly condition, including any lubricant.
Keep chemical identity, hazards and allowed service traceable from receipt to use.
Identify the task before choosing a compound
NCCER module 12109 covers lubricants, cutting fluids, sealants and cleaning materials used in instrumentation. Some products serve more than one function, but a product’s label and technical information define its permitted use. A lubricant that makes a threaded connection easier to assemble can change bolt tension at the same torque. An oil used on a cutting tool can contaminate a clean tubing run if residue remains. A thread sealant applied to a ferrule connection can reach a sealing surface where the fitting procedure calls for a clean, dry surface.
| Product family | Task | What to check |
|---|---|---|
| Assembly lubricant or antiseize | Reduce friction, galling or thread damage at permitted assembly surfaces | Fastener material, required fluid compatibility, assembly torque assumptions and where the product may touch |
| Cutting fluid | Lubricate or cool an authorized cutting operation | Tool, material, cleanup method, and any cleanliness restrictions |
| Thread sealant | Close leakage paths on a compatible threaded joint | Thread type, fluid, temperature, pressure, application method and cure conditions |
| Cleaner or degreaser | Remove grease, debris or residue under the approved cleaning procedure | Wetted materials and seals, exposure controls, residue limits and disposal |
Apply the joint-specific method
Find the joint’s sealing surface first. A Swagelok gaugeable tube fitting seals at its ferrule interfaces, while a tapered threaded port can require an approved thread sealant. See the gaugeable fittings catalog and consumables data. Certain fitting procedures specify lubricant at particular surfaces, especially on listed larger fittings or during certain reassemblies. Treat location and quantity as manufacturer instructions. Avoid putting a compound on the tube or ferrules unless the actual procedure calls for it. Product names such as PTFE tape and anaerobic sealant describe classes of products. Verify the specific product. For example, the Swagelok consumables catalog warns against using its named PTFE-free pipe thread sealant in strong oxidizer systems.
Consider two flanged accessories that specify the same fastener size. One procedure calls for clean, dry threads. Another calls for an identified lubricant and a torque developed for that condition. Using the lubricated procedure on the dry-specified joint can change the resulting clamp load. Follow the procedure for the actual joint and account for fasteners that already have a factory treatment. For example, the Emerson 3051S manual differentiates its supplied stainless and carbon steel flange bolts, and directs users to avoid adding lubricant to either type.
Clean for the application
Before using a cleaner, identify the contaminant. Cutting chips are a different cleanup problem from oil, old sealant or corrosion. Match mechanical cleaning or an approved liquid to the surfaces. Check compatibility with thread finishes, seals, coatings and any instrument that could be exposed. During fabrication, orient and protect openings so removed material does not enter the fluid path. After cleaning, verify the specified condition and protect it with clean closures or packaging until installation.
A tube ordered for oxygen-clean service may arrive capped and sealed. Opening that package next to oily cutting equipment can introduce contamination even if the tube still looks clean. Follow the project cleanliness and handling procedure when a package is breached. A general-purpose solvent cannot establish that a component meets the specified cleanliness condition. Swagelok SC-11 illustrates product-specific cleanliness protection through capped connections and sealed packaging.
Use the label and safety data sheet
OSHA hazard communication covers communication of hazardous chemical information through labels, safety data sheets and training in applicable workplaces. Look at the safety data sheet (SDS) before use. The hazard section describes the hazards. Handling and storage describes conditions and precautions. Exposure controls describes measures such as ventilation and protective equipment. Use the equipment or product technical instructions to decide whether the chemical is compatible with the application. The SDS helps you plan safe handling.
Keep chemical containers identified and store according to the product and site instructions. Confirm condition or shelf life where the product specifies it. Use the approved method for collecting used cleaner and contaminated wipes. For example, if a shop bottle has no usable identification, hold it for resolution through the site’s chemical procedure instead of guessing the contents by odor. That prevents both an uncontrolled exposure and a potentially incompatible chemical from entering the system.
Sources checked November 16, 2026. NCCER module 12109, OSHA hazard communication, Swagelok consumables catalog, Emerson 3051S flange bolt instructions.
A valve manifold procedure specifies dry fasteners. A technician proposes lubricating them and applying the same torque. What should guide the decision?
Lubricate every fastener because torque fully determines load.
Use any fluid that makes the nut move easily.
Use the specified assembly condition, because lubrication changes the relationship between torque and clamp load.
Increase torque until all washers deform.
What is the first check before using a solvent cleaner on a transmitter manifold with installed seals?
Check the approved cleaning method and product compatibility, then use the label and SDS to plan safe handling.
Select the solvent with the strongest odor.
Mix it with the sealant to see whether it cures.
Use any solvent if the metal is stainless steel.
A component specified as oxygen-clean arrives in a torn package with its process connection uncapped. What should the technician do?
Install it if the exposed metal looks bright.
Hold it for the approved cleanliness inspection or disposition.
Apply general-purpose oil before installing it.
Wipe the connection with any shop cloth and treat it as certified clean.
Sections you finish are checked off in the contents.