5.4 Cascade, Feedforward, Ratio and Split-Range Control

Key Takeaways

  • The outer loop requests the inner loop’s setpoint. Verify the inner response and return its tracking and limit information as designed.

  • A feedforward term follows a measured disturbance. Its effect depends on the model, timing and available final-element authority.

  • Three-element boiler drum control combines drum level, steam flow and measured feedwater flow.

  • Put ratio and cross-limit signals on the required basis before multiplying or selecting them.

  • A split-range crossover point differs from a finite command gap. Verify normal response, transfer and the specified failure behavior.

Last updated: November 2026

Cascade, Feedforward, Ratio and Split-Range Control

Follow each signal to see which measurement is being controlled, which signal sets a target, and which device moves the final element. Many faults in multi-loop control arise from the selected mode, the engineering units or a limit between two controllers.

Cascade control

A primary controller's output becomes the remote setpoint of a secondary controller, which regulates its own variable. For example, an outlet temperature controller can request a steam-flow setpoint. The steam-flow controller measures steam flow and commands the valve.

Temperature SP and PV → Temperature controller → Steam-flow SP
Steam-flow SP and PV  → Steam-flow controller  → Steam valve

The secondary loop needs useful response speed relative to the primary and must measure a path that sees the relevant disturbance. A supply pressure change can affect measured steam flow before the resulting temperature change is measurable. The inner loop can then correct flow earlier. Verify this with measured response, available flow and valve authority. A fixed speed ratio does not establish the benefit for every installation.

An approved commissioning sequence commonly verifies and tunes the inner loop at its local setpoint before testing the outer loop in cascade. Match the secondary setpoint and the primary output in the correct units and verify the mode and limits before transfer. Check tracking when the inner loop leaves cascade or reaches a limit. The Logix PIDE primary-loop function provides initialization and windup flags for this purpose when connected to the primary controller.

Feedforward with feedback trim

Feedforward uses a measured disturbance to calculate a compensating command. If the disturbance is measured far enough upstream and the corrective path is sufficiently fast, the controller can act before the disturbance's effect shows in the PV. Feedforward still depends on the size and timing of the disturbance and the model. Feedback trim addresses remaining measured error and can respond to disturbances that have no feedforward measurement.

For a local linear steady-state model, let GuG_u be the signed change in PV per unit manipulated command and GdG_d the signed change per unit disturbance. With ΔPV=GuΔu+GdΔd\Delta PV=G_u\Delta u+G_d\Delta d, a steady correction is Δuff=−(Gd/Gu)Δd\Delta u_{\text{ff}}=-(G_d/G_u)\Delta d for Gu≠0G_u\ne0. If one load unit raises the PV by 3 units and one command point lowers it by 2 units, the model calls for 1.5 additional command points per load unit. The calculation says nothing about whether the correction arrives in time or fits within the limits.

Three-element boiler drum control

A change in steam demand can change pressure and the volume of steam bubbles under the drum water surface. A level swell can occur while water inventory is falling. The Yokogawa three-element example uses steam flow to set the feedwater demand, drum level to trim it, and measured feedwater flow in the secondary loop that commands the feedwater valve. Steam and feedwater must be on compatible flow bases. Check proper flow measurement range, mode, limits and startup logic. In a specified startup strategy, a unit may use single-element level control until the flow measurements are suitable for cascade. This control arrangement does not establish how an independent protective trip will behave.

Ratio and cross-limiting

A ratio station sets a target for one stream from the measured flow of another. For a blend with a mass ratio of 0.25 kg B per kg A, 80 kg/min on the wild stream A gives SPB=0.25(80)=20 kg/minSP_B=0.25(80)=20\,\text{kg}/\text{min}. The B controller uses the measured B flow to position its valve. Confirm the ratio basis and the handling of invalid or very low measurements.

In Yokogawa's metered boiler example, a low selector limits fuel demand based on the measured air available, and a high selector holds enough air demand for the measured fuel. The configured pattern permits air to lead fuel as firing demand increases and fuel to lead air downward as demand falls. The design accounts for instrument behavior and the approved burner operating envelope. Cross-limiting is a combustion-control function. Flame supervision, permissives, trips and shutoff are functions of the applicable burner safety system.

Split range and override selection

A split-range arrangement maps different segments of one command to different final elements. In an example with a common 4–20 mA command, the cooling valve travels from 100% to 0% open as current rises from 4 to 12 mA. The heating valve travels from 0% to 100% open as current rises from 12 to 20 mA.

Common commandCooling openHeating open
4 mA100%0%
8 mA50%0%
12 mA0%0%
16 mA0%50%
20 mA0%100%

In this ideal linear travel mapping, 12 mA is one crossover point. A dead zone between commands would require a finite range with both valves held closed. Some designs specify overlap instead. The Fisher 3661 instructions give model-specific springs and limits for local split-range operation. A controller can also compute the split and send a full-range signal to each separate positioner. Verify both normal travel directions and each specified failure condition.

In an override arrangement, a selector can choose among multiple demands for a single output. If higher command means more pump speed, a low selector can pass the lower of a normal flow demand of 65% and an equipment limit of 40%. The result is 40%. Confirm the direction works for the actual manipulated variable and that the unselected controllers handle tracking or windup. Verify transfer and release without assuming the selector alone provides protective shutdown.

Test Your Knowledge

A temperature controller supplies a remote setpoint to a coolant-flow controller. Which commissioning result supports selecting cascade for rejection of coolant supply disturbances?

A

The stable inner loop detects and corrects flow disturbances sooner than the temperature loop can respond, and mode transfer and tracking have been verified.

B

The temperature loop reacts first, so it can compensate for flow before the inner measurement changes.

C

Both loops have identical time constants and simultaneous ultimate-gain settings.

D

The coolant controller always accepts the remote setpoint even when it is in manual.

Test Your Knowledge

In a three-element drum-level control design, what happens to the feedwater flow setpoint and valve command when the measured steam flow rises during normal operation?

A

Drum pressure and steam flow jointly open the valve with no feedwater measurement.

B

The higher steam measurement directly increases fuel gas flow.

C

Steam flow increases feedforward demand, drum level supplies trim, and the measured feedwater-flow loop commands the valve.

D

Drum level is replaced by steam flow as the only feedback measurement.

Test Your Knowledge

A common 4–20 mA split-range command closes a cooling valve linearly from 100% to 0% over 4–12 mA and opens a heating valve linearly from 0% to 100% over 12–20 mA. Below its active range the heating valve stays closed, and above its active range the cooling valve stays closed. What positions are commanded at 10 mA and how should the 12 mA condition be described?

A

Cooling 75%, heating 0%; a finite gap at 12 mA.

B

Cooling 0%, heating 25%; a single crossover at 12 mA.

C

Cooling 25%, heating 25%; an overlap at 12 mA.

D

Cooling 25%, heating 0%; both closed at the single 12 mA crossover.

Sections you finish are checked off in the contents.