8.1 Liquid Analysis: pH, ORP, Conductivity and Dissolved Oxygen
Key Takeaways
pH is the negative base-10 logarithm of hydrogen-ion activity. The ideal electrode slope magnitude at 25 °C is about 59.16 mV per pH unit.
Distinguish temperature correction of the electrode, the assigned buffer value at calibration temperature, and any configured solution temperature model.
Use the assigned buffer values and the approved slope and offset limits. Verify the measurement path before diagnosing a failed sensor.
Specify reference and temperature when comparing ORP. Apply the selected conductivity cell constant and reporting basis.
Polarographic dissolved-oxygen sensors consume oxygen during measurement. Optical sensors use luminescence quenching.
Liquid Analysis: pH, ORP, Conductivity and Dissolved Oxygen
This supplemental lesson from NCCER's Analyzers and Monitors curriculum covers four distinct measurements. Begin with the required quantity and reporting basis. Inspect the sample path and sensing surface before adjusting the transmitter.
Measure pH and interpret the voltage
IUPAC defines pH from hydrogen-ion activity in solution. The activity includes interaction with the solution. A one-unit increase in pH means a tenfold decrease in hydrogen-ion activity. Neutral pure water is near pH 7 at 25 °C. The neutral point changes with temperature, and pH values outside the familiar 0–14 range are possible.
A combination probe places a glass measuring electrode and a reference electrode in one assembly. The hydrated glass responds to hydrogen-ion activity across the glass. A common reference uses silver/silver chloride in a chloride electrolyte. Its junction provides ionic contact with the sample. The transmitter reads the potential difference. A temperature element can supply the temperature used in the conversion. The high impedance of the glass circuit makes it sensitive to leakage across wet or contaminated connections. Use the designated cable, preamplifier arrangement and connection practices for the installed sensor.
For an ideal example with the voltage falling as pH rises, use a reference point at pH 7, with the voltage at that point. Then
Here and are in mV, is in kelvins, is the molar gas constant, and is the Faraday constant. The factor 1000 converts volts to millivolts. The ideal slope magnitude is 59.16 mV per pH unit at 25 °C, 64.12 at 50 °C and 69.08 at 75 °C. Under this model, gives about +177.5 mV at pH 4.00 and −177.5 mV at pH 10.00 at 25 °C. Sense polarity, offset, and the practical response of the installed assembly come from the instrument and calibration.
| Temperature-related function | What changes |
|---|---|
| Electrode temperature compensation | Uses the sensor temperature to account for the temperature dependence of electrode response. The reported pH ordinarily applies at the sample temperature. |
| Buffer temperature table | Supplies the reference buffer's assigned pH at calibration temperature. IUPAC's equimolal phosphate example is 6.865 at 25 °C and 6.833 at 50 °C. |
| Solution temperature correction | An optional, separate model converts a known sample chemistry's pH to another reference temperature. It needs a suitable known relationship and configured method. |
Calibrate and examine sensor condition
Select two fresh compatible buffers that bracket the expected measurement when practical. Confirm the buffer family and temperature values, rinse between samples and wait for the specified stability before recording or accepting each point. Use the sensor instructions for cleaning, storage and any replacement of the junction or fill. The Rosemount 1058 procedure supports automatic buffer recognition and manual value entry and reports the fitted slope referred to 25 °C.
For an illustrative calibration using assigned values 7.00 and 4.01 at 25 °C, the ideal span is mV. Suppose the readings are +12 and +182 mV respectively. The measured span is 170 mV, or about 56.86 mV per pH unit and 96.1% of ideal. The +12 mV at pH 7 is the measured offset for this convention. Compare both values and the response time with the approved limits. For example, the Rosemount 1066 documents configurable calibration parameters, including a default offset limit of 60 mV. A site may set a tighter limit. A large shift can indicate a reference or junction issue, contaminated buffers or a connection problem. Examine the glass and junction, verify buffers and temperature, and check the complete signal path before diagnosing a failed part.
Interpret an ORP reading
Oxidation-reduction potential (ORP) is the potential of an indicator electrode, often platinum, relative to its reference. State the reference system when comparing mV values. For example, the ORP of a test solution stated against saturated Ag/AgCl at a specified temperature differs from its value against the standard hydrogen electrode. Use the value appropriate to the sensor and temperature when checking with a standard. The Rosemount 1058 uses a single-point ORP standardization. Liquid composition, pH, temperature, electrode condition and equilibration can all affect ORP. A trend can support an approved treatment control method. A single reading cannot establish a universal reagent dose, reaction endpoint or disinfection result.
Measure conductivity and dissolved oxygen
Conductance is in siemens for the measured resistance . The conductivity is for effective cell constant in inverse length. For ideal parallel plates . Use the actual calibrated or rated cell constant for a practical cell. A measured resistance of 2.00 kΩ with gives , or 50.0 µS/cm, at the measurement temperature. Reference-temperature reporting requires the method's compensation model. USGS specific conductance practice reports at 25 °C. Check the method for requirements to use or record uncompensated values.
| Technology | Application and check |
|---|---|
| Contacting conductivity | An alternating electrical excitation measures the conductance through wetted electrodes. Choose the cell constant, range and material for the solution, and inspect the measuring surface. |
| Toroidal conductivity | A drive coil induces a current loop through the liquid and a pickup coil senses it without exposed measuring electrodes. Check compatibility, conductivity range, bubbles, deposits and wall effects. The Indumax CLS54D guide shows how wall clearance and pipe material can change its installation factor. |
| Polarographic dissolved oxygen | Oxygen diffuses through a membrane and is consumed at the electrode. Check the specified sample movement, membrane, electrolyte, and polarization requirements. |
| Optical dissolved oxygen | Oxygen quenches a luminescent sensing layer, changing its luminescence lifetime. The sensing reaction consumes no oxygen. Inspect the cap, verify response and ensure the sample remains representative. |
Conductivity responds to the ions present and to their mobility. Replacing a concentration assay with conductivity requires a validated relationship for that mixture and temperature range. Dissolved oxygen readings in mg/L and percent saturation also have distinct bases. Verify the instrument's salinity, temperature and pressure handling and calibration conditions for the selected reporting mode.
A plant procedure sets a maximum ±30 mV zero offset for a pH loop. In fresh buffer assigned pH 7.00 at 25 °C, the as-found reading is +52 mV. What conclusion does this check support?
The probe passes because a different transmitter may have a 60 mV default.
The result fails the site offset limit; verify the buffer and sensing path before deciding on the corrective action.
The offset identifies a cracked glass electrode without any other checks.
The raw offset establishes a specific RTD calibration error.
An approved toroidal probe is installed in a conductive cleaning solution. After moving it into a smaller pipe of a different material, a reading disagrees with a reference on the same temperature basis. What should the technician check?
The polarity of a pair of exposed metal measuring electrodes on the toroidal sensor.
A fixed 2% per degree correction as the only possible source of error.
The required installation factor, wall clearance, and whether liquid fills the bore without bubbles or deposits.
An electrode polarization voltage that every toroidal probe needs.
With the standard electrode slope correction enabled and solution temperature correction disabled, how does the ideal slope magnitude change when liquid temperature rises from 25 °C to 75 °C?
From about 59.16 to 69.08 mV per pH unit, accounting for the electrode response.
From about 69.08 to 59.16 mV per pH unit, accounting for lower absolute temperature.
The slope stays fixed because pH is unitless.
The slope stays fixed and every sample is converted to its actual pH at 25 °C.
Sections you finish are checked off in the contents.