1.4 Gaskets, O-Rings & Packing
Key Takeaways
A flange gasket seals between stationary faces under compressive load from the joint fasteners.
An O-ring seals by deforming in its specified gland. Select the compound and dimensions for the equipment, fluid and operating conditions.
Stem packing seals around a moving stem. Changes to packing material or loading can change friction and actuator demand.
Before replacing a seal, isolate the equipment and match the approved part, surface condition and assembly procedure.
Locate the sealing interface
A process-fluid leak on the outside of a valve can come from the bonnet joint, the flange or the stem. Trace the leak location before selecting a spare. The look and size of a seal are only two parts of the identification. A correct part also has to fit the joint geometry and tolerate the fluid, temperature and pressure for that assembly. Use the equipment bill of materials, specification and maintenance instructions before opening a joint. See NCCER module 12108.
| Seal | Location | How it seals | What to verify |
|---|---|---|---|
| Gasket | Static joint between flanges or covers | The joint compresses the gasket between the sealing faces. | Flange or cover design, face condition, gasket dimensions and material, specified bolt-load procedure |
| O-ring | Formed gland in a connector, cover or moving member | The gland squeezes the ring and confines it at the interface. | Part number, compound, cross-section, gland geometry, media and pressure exposure |
| Packing | Stuffing box around a valve stem or shaft | The packing set forms a seal around a member that can move against it. | Stem and box condition, packing type, ring orientation, preload and permitted adjustment |
Flange gaskets and joint loading
A gasket needs adequate, distributed compressive load. The load has to seat the gasket across the intended sealing area and maintain integrity during service. Joint dimensions, flange condition, fasteners and gasket compressibility all affect the outcome. Raised-face and flat-face joints can use different gasket geometries. Verify that the gasket will seat where intended without obstructing the bore. Use the gasket specified for that assembly rather than inferring interchangeability from an outside diameter.
After safe isolation, check face condition and remove old material by the approved method. Gouges, embedded fragments or misalignment can defeat a new gasket. Garlock’s manual describes cleaning and inspecting faces, centering the specified gasket, and loading compatible bolted joints uniformly using the prescribed tightening sequence. For a circular bolted flange, staged cross-pattern passes are one common method when specified. Use the equipment procedure for torque, lubricant, pass sequence and fastener condition. Garlock’s gasket-reuse guidance explains that many compressed gaskets lose resealing ability after service. Follow the joint’s replacement requirements when it is opened.
O-rings and gland condition
An O-ring has a circular section. It is squeezed in the gland, the space formed by the groove and the mating surface. A static cover can use axial compression, while a piston or connector can use radial compression. In a dynamic seal, motion introduces friction and wear. The Parker O-Ring Handbook uses separate design guidance for static and dynamic applications and considers fluid compatibility, temperature, clearance and material hardness. A ring can swell, harden or take a permanent set. Pressure can drive a seal into an excessive clearance gap, a failure called extrusion. Use backup rings only where the design specifies them.
A ring from a nearby store bin can match the old ring’s measured size and still be wrong for the service. Check the new part against the design, inspect the groove and the mating surface, and use only the permitted installation lubricant. Keep the seal clean and avoid twisting or nicking it during assembly. An abrasion track or a cut at a port edge gives a better diagnostic lead than assuming the replacement needs additional compression.
Stem packing and friction
Packing around a sliding stem is loaded by a follower or spring arrangement. The parts maintain contact with the stem while allowing motion. Too little loading can allow leakage. Excessive friction can cause poor motion or require more actuator force. Use the applicable valve manual to identify how the particular packing set is installed and loaded. Emerson’s Fisher selection guidance distinguishes packing products by service and friction. Material families such as polytetrafluoroethylene (PTFE) and graphite are design options, each with several grades and assemblies. Check the valve model and service limits before substituting one for the other.
Imagine a valve that started sticking after a packing replacement. The work record shows a change to another packing set. Before changing positioner tuning, compare the approved packing configuration, assembly procedure and observed valve travel. An increase in breakaway force can arise from the changed packing or how it was loaded. Verify the assembly under the authorized repair and test procedure.
Sources checked November 16, 2026. NCCER instrumentation curriculum, Garlock gasket manual, Parker O-Ring Handbook, Emerson Fisher packing guidance.
A joint is leaking between two stationary flanges. Which part and interface should be checked first after safe isolation?
Stem packing around the actuator rod
The specified flange gasket and the two seating faces
The transmitter input terminal block
A backup ring from a different connector
A spare O-ring has the same dimensions as the listed part, but its compound is unknown. What is the correct basis for accepting a replacement?
Accept it if its color matches.
Use it if the flange is held by new bolts.
Verify its specified dimensions and compound against the gland, fluid and operating conditions.
Choose the softest ring that fits in the groove.
A sliding-stem valve begins sticking immediately after replacement with a different packing set. Which change is a reasonable first diagnostic lead?
The new packing can change stem friction or loading.
The packing changed the tubing diameter.
The process flange gasket sets actuator travel.
The analog input resistor is part of the packing stack.
Sections you finish are checked off in the contents.