1.2 Craft Mathematics, Pressure Head & Engineering Unit Conversions

Key Takeaways

  • Use 25.4 millimeters per inch exactly. Length, area and volume use the first, second and third powers of the length factor.

  • Use the Pythagorean theorem for the distance between perpendicular coordinates and the rise-to-run ratio for slope.

  • Use the specified water-column reference. The NCCER formula sheet uses 27.68 inches of water per psi.

  • Check loop terminal voltage by subtracting all external load drops from the minimum supply voltage at the specified current.

  • Linear scaling subtracts the input lower range value before dividing by span, then applies the same fraction to the output span.

Last updated: November 2026

Convert measurements with the units attached

NCCER’s craft mathematics objectives cover inch-pound and metric units, algebra, angles and common geometric figures. Write the unit next to every value and select a conversion factor that cancels the starting unit. NIST defines 1 inch as exactly 25.4 millimeters. For example, 3/8 inch = 0.375 inch × 25.4 mm/in = 9.525 mm. The mathematical conversion does not by itself establish compatibility with a nominal metric fitting.

QuantityConversion or relationShop example
LengthMultiply inches by 25.4 to get millimeters.7.5 inches is 190.5 mm.
AreaMultiply square inches by 25.4² to get square millimeters.A 3 in × 2 in rectangle is 6 in², or 3,870.96 mm².
VolumeMultiply cubic inches by 25.4³ to get cubic millimeters. Divide by 1,000 to get milliliters.A 1 in³ cavity is about 16.39 mL.
MassMultiply pounds avoirdupois by 0.45359237 to get kilograms.A package marked 10 lb has mass about 4.54 kg.

A scale label in pounds commonly expresses mass. A force calculation can use pounds-force (lbf) or newtons (N). Keep those quantities separate, especially when using force divided by area to determine pressure. NIST SP 811 lists the factors and their reference conditions.

Read geometry from a drawing

A circle has a radius measured from its center and a diameter twice that radius. Its area is π times radius squared. For example, a circular opening with diameter 0.500 inch has radius 0.250 inch and area about 0.196 in². A triangle and a rectangle are polygons with straight sides. A right angle is 90°, an acute angle is smaller than 90°, and an obtuse angle is greater than 90° and less than 180°. Classify the actual angles or use the written dimensions on the drawing.

Two fittings lie 24 inches apart horizontally and 7 inches apart vertically in the same plane. The straight centerline distance is √(24² + 7²) = 25 inches. For a straight diagonal, the tangent of its angle above horizontal is 7/24, so the angle is about 16.3°. The 25-inch measurement is between the stated reference points. Fabrication length can change when the route uses bend radii and the endpoints use fitting insertion depths. See NASA’s right-triangle relationships.

Hydrostatic Pressure & Liquid Head Principles

Hydrostatic pressure is the pressure exerted by a fluid at rest due to the force of gravity acting on its mass. In physical terms:

P = ρ × g × h

Where:

  • P = Hydrostatic pressure
  • ρ = Fluid density
  • g = Acceleration due to gravity (9.81 m/s² or 32.174 ft/s²)
  • h = Height of the liquid column above the measurement datum

Specific gravity and reference conditions

Specific gravity (SG) is a density ratio to a stated reference fluid. For the liquid-head exercises here, use the supplied process-liquid SG relative to the reference water density. If the liquid is static and uniform, a vertical liquid height multiplied by SG gives its equivalent height of the reference water column.

The NCCER formula sheet uses 27.68 inH₂O per psi. For the 4 °C water convention, NIST SP 811 gives 249.082 Pa per inch and 6,894.757 Pa per psi. Their ratio is approximately 27.68 inches per psi. Use the specified reference for a water-column reading.

The Practical Head Pressure Formula

To calculate the pressure at the bottom tap of an open, atmospheric liquid storage vessel:

Pressure (psi) = [Height (inches) × Specific Gravity] / 27.68
Height of Water Column (inH2O) = Height of Liquid (inches) × Specific Gravity

Industrial Pressure Unit Conversion Matrix

Match the instrument to the units in the specification, and use the supplied reference when converting.

UnitEquivalent in 1 psiEquivalent in 1 barCommon Craft Application
Pound per Square Inch (psi)1.0000 psi14.5038 psiStandard US process piping, hydraulic, and steam ratings
Inches of Water Column (inH2O @ 4°C)27.681 inH2O401.47 inH2OLow-pressure draft, tank level measurement, differential pressure across filter banks
Inches of Mercury (inHg @ 0°C)2.0360 inHg29.530 inHgCondenser vacuum, barometric pressure, vacuum pumps
Kilopascals (kPa)6.8948 kPa100.00 kPaMetric industrial transmitter calibrations, European DCS standards
Bar0.06895 bar1.0000 barHydraulic systems, offshore process manifolds, gas cylinders
Millimeters of Water Column (mmH2O, conventional)703.07 mmH2O10,197 mmH2OInternational low-pressure draft and level instrumentation
Atmosphere (atm, standard)0.06805 atm0.9869 atmThermodynamic process calculations (1 atm = 14.696 psia)

Gauge Pressure vs. Absolute Pressure

  • Gauge Pressure (psig): Pressure measured relative to local atmospheric pressure. A disconnected gauge open to the air reads 0 psig.
  • Absolute Pressure (psia): Pressure measured relative to a perfect, complete vacuum. A standard atmosphere is about 14.696 psia. Use the actual local barometric pressure when a field problem provides it.
P_absolute = P_gauge + P_atmospheric
P_gauge = P_absolute - P_atmospheric

Trap Alert: If local barometric pressure is 29.92 inHg and the vacuum gauge indicates 20.0 inHg below atmosphere, the absolute pressure is 29.92 inHg − 20.0 inHg = 9.92 inHg absolute (or approx. 4.87 psia).


Worked Step-by-Step Hydrostatic Head Calculations

Example 1: Atmospheric Water Storage Vessel

  • Problem: An open atmospheric water tank contains water with assumed SG = 1.00 filled to a height of 180 inches above the transmitter centerline. Calculate the hydrostatic pressure at the transmitter tap in both inH2O and psi.
  • Step 1: Calculate effective water column height: h_eff = 180 inches × 1.00 = 180 inH2O
  • Step 2: Convert to psi using the 27.68 constant: Pressure = 180 inH2O / 27.68 inH2O/psi = 6.503 psi

Example 2: Fuel Oil Day Tank

  • Problem: A diesel generator fuel oil day tank holds fuel oil with an SG of 0.85. The vented tank contains a 240-inch oil column above the sensing point. What is the pressure sensed by the transmitter?
  • Step 1: Compute effective head in inches of water: h_eff = 240 inches × 0.85 = 204 inH2O
  • Step 2: Convert to psi: Pressure = 204 / 27.68 = 7.370 psi
  • Notice: If the technician had ignored specific gravity and assumed water, they would have incorrectly calculated 240 / 27.68 = 8.671 psi, introducing an error of +17.6%.

Example 3: Dense Liquid in a Vented Vessel

  • Problem: A vented vessel contains a solution whose measured specific gravity is 1.32 at operating conditions. The level spans 96 inches. What is the full-scale hydrostatic pressure in psi and kPa?
  • Step 1: Effective water head: h_eff = 96 inches × 1.32 = 126.72 inH2O
  • Step 2: Convert to psi: Pressure (psi) = 126.72 / 27.68 = 4.578 psi
  • Step 3: Convert to kPa using 1 psi = 6.895 kPa: Pressure (kPa) = 4.578 psi × 6.8948 kPa/psi = 31.56 kPa

Ohm's law and DC loop calculations

A two-wire loop-powered transmitter uses the same series path for power and signal. The series current is the same at each point in the path. Each external load uses some supply voltage, leaving the rest across the transmitter. The transmitter can regulate the required current while its operating limits are met.

Fundamental DC Electrical Formulas

Voltage (V) = Current (I) × Resistance (R)
Current (I) = Voltage (V) / Resistance (R)
Resistance (R) = Voltage (V) / Current (I)
Power (P) = Voltage (V) × Current (I) = I² × R = V² / R

Units: Voltage in Volts (V), Current in Amperes (A; note that 20 mA = 0.020 A), Resistance in Ohms (Ω), Power in Watts (W).

Instrument loop burden and terminal voltage

For linear series resistances, multiply the total resistance of both cable conductors and series loads by the current. Subtract that drop and any other specified voltage drops from the supply. Receiver loads, indicators and barriers can have different voltage requirements. The loop must also meet the transmitter’s specified load curve and any communication or hazardous-area requirements.

V_at_transmitter = V_supply − I × R_external   (series resistances only)
R_external,max = (V_supply − V_transmitter,min) / I_max

The algebra follows from solving the voltage equation for resistance at the minimum allowable terminal voltage. Use the lowest expected supply and the highest current the complete application requires, including any configured overrange or alarm current. For example, the Rosemount 3051 datasheet supplies an operating-region curve and a separate minimum communication load for its 4–20 mA HART model. Use the curve for that model.

Worked Loop Burden Calculation

  • Scenario: A calculation exercise assumes a 24 VDC supply, a transmitter minimum of 11.5 VDC at 20 mA and the following series resistances. The loop contains:
    • DCS input card sensing resistor: R_sense = 250 Ω
    • Series accessory in this exercise: R_accessory = 300 Ω
    • Total field cable resistance (both legs): R_wire = 30 Ω
  • Step 1: Calculate total external circuit resistance: R_total_ext = 250 Ω + 300 Ω + 30 Ω = 580 Ω
  • Step 2: Calculate maximum voltage drop across external components at full-scale signal (20 mA = 0.020 A): V_drop_ext = 0.020 A × 580 Ω = 11.60 VDC
  • Step 3: Determine available voltage at transmitter terminals: V_terminals = 24.00 VDC - 11.60 VDC = 12.40 VDC
  • Step 4: Evaluate compliance: Because 12.40 VDC > 11.50 VDC, the specified terminal-voltage minimum is met with 0.90 VDC to spare at this test point.
  • Step 5: Maximum allowable external loop resistance for this circuit: R_max = (V_supply - V_terminal_min) / I_max = (24.0 V - 11.5 V) / 0.020 A = 12.5 V / 0.020 A = 625 Ω

Resistor Power Dissipation

Technicians must verify the wattage rating of precision resistors installed in signal loops. At maximum signal (20 mA):

P = I² × R = (0.020 A)² × 250 Ω = 0.0004 A² × 250 Ω = 0.100 W (100 mW)

Use the component datasheet to select a power rating with headroom at the actual ambient temperature and worst-case current. Check resistance tolerance and temperature coefficient against the accuracy required by the input.


Process Signal Scaling & Linear Interpolation

Scaling maps a measured physical value (e.g., gpm, psig, °F) to an analog electrical or pneumatic transmission signal.

The Standard Linear Scaling Formula

Output = [ (Input - LRV_in) / (URV_in - LRV_in) ] × (URV_out - LRV_out) + LRV_out

Where:

  • LRV = Lower Range Value (process value at 0% signal)
  • URV = Upper Range Value (process value at 100% signal)
  • Span = URV − LRV
Fractional Span = (Input - LRV_in) / Input_Span
Output = (Fractional Span × Output_Span) + Output_min

For standard 4–20 mA current loops:

  • Output_min = 4.0 mA
  • Output_Span = 20.0 mA - 4.0 mA = 16.0 mA
Current (mA) = [ (Process Value - LRV) / Span ] × 16.0 mA + 4.0 mA

Worked Scaling Problems

Problem 1: Flow Rate to Signal Current

  • Parameters: The transmitter is configured for a linear-in-flow 4–20 mA output over 0 to 600 gallons per minute (gpm). Current flow rate is 420 gpm.
  • Step 1: Calculate process span: Span = 600 - 0 = 600 gpm.
  • Step 2: Determine fractional span: Fraction = (420 - 0) / 600 = 0.70 (or 70.0%)
  • Step 3: Calculate mA output: Current = (0.70 × 16.0 mA) + 4.0 mA = 11.20 mA + 4.0 mA = 15.20 mA

Problem 2: Signal Current to Pressure Value (Positive LRV)

  • Parameters: Pressure transmitter calibrated with an LRV of 50 psig and a URV of 250 psig. A technician measures 10.40 mA of loop current with the specified test method. What is the process pressure?
  • Step 1: Calculate signal percentage: Fractional Span = (10.40 mA - 4.0 mA) / 16.0 mA = 6.40 / 16.0 = 0.40 (or 40.0%)
  • Step 2: Calculate process span: Span = 250 psig - 50 psig = 200 psig.
  • Step 3: Calculate process value: Pressure = LRV + (Fractional Span × Span) = 50 psig + (0.40 × 200 psig) = 50 + 80 = 130 psig

Temperature Conversion Mathematics

Industrial temperature measurements involve four primary scales: Celsius (°C), Fahrenheit (°F), Kelvin (K), and Rankine (°R).

°C = (°F - 32) / 1.8
°F = (°C × 1.8) + 32
K = °C + 273.15
°R = °F + 459.67

Worked Temperature Conversion

  • Problem: A distillation column reboiler thermocouple indicates an operating temperature of 365°F. Convert this measurement to Celsius and Kelvin.
  • Step 1: Convert Fahrenheit to Celsius: °C = (365 - 32) / 1.8 = 333 / 1.8 = 185.0°C
  • Step 2: Convert Celsius to absolute temperature Kelvin: K = 185.0°C + 273.15 = 458.15 K

Sources checked November 16, 2026. NCCER craft mathematics objectives, NIST SP 811.

Test Your Knowledge

A vented tank contains oil with a specific gravity of 0.88. The stable liquid surface is 220 inches above the pressure tap. Using 27.68 inches of water per psi, what gauge pressure does the liquid head produce?

A

4.25 psig

B

6.99 psig

C

7.95 psig

D

8.62 psig

Test Your Knowledge

A series instrument loop has a 24.0 VDC supply and external resistances of 250, 310 and 40 ohms. At 20 mA the transmitter requires at least 11.5 VDC at its terminals. Does the calculated voltage meet that requirement?

A

10.2 VDC, below the minimum

B

14.6 VDC, 3.1 VDC above the minimum

C

12.0 VDC, 0.5 VDC above the minimum

D

12.0 VDC, 6.0 VDC below a universal 18 VDC minimum

Test Your Knowledge

A differential-pressure flow transmitter is configured so its 4–20 mA output is linear in flow from 0 to 450 gpm. Measured loop current is 14.8 mA. What flow does it represent?

A

303.75 gpm

B

281.25 gpm

C

337.50 gpm

D

315.00 gpm

Test Your Knowledge

Two points lie 12 inches apart horizontally and 5 inches apart vertically in the same plane. What is the straight-line centerline distance between the points?

A

5 inches

B

7 inches

C

17 inches

D

13 inches

Sections you finish are checked off in the contents.