9.3 Maintaining Valves

Key Takeaways

  • Secure isolation, render stored energy safe and verify conditions before opening a valve. Include actuator forces and pressure trapped in the body or packing box.

  • Use the specified packing set, O-ring compound, lubricant and installation method for the exact valve.

  • Support the bonnet and control the position of internals and preload before removing fasteners. Fit the specified new seal for reassembly.

  • Troubleshoot by tracing the leak to the packing, bonnet, end joint, through-seat path or actuator. Confirm other possible sources of downstream pressure.

  • Use an approved repair or replacement and verify the specified functional, seat and pressure-boundary checks before return to service.

Last updated: November 2026

Maintaining Valves

Quick Answer: Secure and verify process and actuator isolation before opening a pressure boundary. Determine whether the leak is at the packing, body-bonnet joint, end connection or seat. NCCER’s 08408 curriculum covers packing, O-rings, bonnet work and troubleshooting. These topics supplement the PFT08_03 outline, which lists 08203 for valve identification and installation.

A leaking stem, a passing seat and a cracked body call for different decisions. Start with the valve identification, the manufacturer’s maintenance instructions and the piping owner’s work scope.

Energy isolation before opening

  1. Identify process pressure, thermal and chemical contents, potential feeds and actuator energy. Plan supports and the opening with operations.
  2. Shut down and operate the identified isolating devices, then apply the applicable lockout or tagout procedure. For covered U.S. general-industry servicing, 29 CFR 1910.147(d) places these steps before relieving or restraining residual energy. Covered PSM processes also require safe opening practices under §1910.119(f)(4). Construction uses its applicable rules, including §1926.417 for circuits, and the employer’s process isolation procedure.
  3. Safely depressurize and drain both sides as specified. Address trapped body cavities, bonnet or packing-box pressure, actuator loading fluid, spring preload and connected forces. Cool, purge or decontaminate if required by the service. Follow the manufacturer’s cavity release procedure.
  4. Verify effective isolation and deenergization, including absence of hazardous pressure. Where it can reaccumulate, continue verification as required. Use the approved indicator, vent and verification method. Do not use the bonnet bolts to check for stored pressure.
  5. Support the valve and connected pipe before disassembly. If positive isolation requires a blind introduced at a first break, establish and verify safe conditions at that opening before the blind goes in.

Packing replacement (stem sealing)

Packing seals the moving stem where it passes through the bonnet or body. The ring or cartridge design sets the replacement method.

Symptoms of packing problems:

  • Leakage at the packing gland / stem
  • Stem hard to turn (overtight packing or dry packing)
  • Stem scoring from dirt embedded in packing

Typical replacement outline (always follow manufacturer and site procedure):

  1. Complete and verify the approved energy and process isolation before disturbing the gland or seal.
  2. Back off gland nuts; remove gland follower as designed
  3. Remove the old packing with the tools specified by the valve manufacturer. Protect the stem and stuffing-box wall from scratches.
  4. Clean stuffing box; inspect stem for pits, scores, and bent condition
  5. Install correct packing type and size (die-formed rings, braided rings, lantern rings if used for purge/lube)
  6. Seat the specified rings in order and stagger split-ring joints as directed. For example, Chesterton 1600 instructions specify 180° for two rings, 120° for three, or 90° for four or more. Molded solid sets and spring-loaded V-rings follow their own instructions.
  7. Set the gland evenly to the required compression or fastener setting and verify stem travel under the approved test procedure.
  8. Inspect for leakage after startup. Follow the manufacturer and site instructions for adjustment and isolation.
Packing issueLikely causeCorrect direction
Drip at stem, gland loosePacking relaxation or wearVerify the specified gland setting and inspect under approved isolation before any packing replacement
Stem will not turn after “fix”Possible over-compressionVerify isolation and the specified gland setting. Replace damaged packing.
Leak after new packingWrong size, cut alignment, scored stemCorrect rings; repair/replace stem if scored
Leak only at certain stem positionsStem may be worn in part of its travelInspect stem finish and packing under isolation before choosing parts

Live-loaded packing (springs) maintains gland load; do not defeat spring hardware. Fugitive-emission packing sets on environmental services require exact materials and the specified gland loading. Use the qualified set and follow its instructions.

O-rings and soft seals

Quarter-turn valves, bonnet seals, cartridge seals, and some stem seals use O-rings or elastomeric seats.

Craft rules:

  • Match the specified size and compound to the service. Nitrile, EPDM and FKM are elastomers. PTFE may be used as a backup ring or packing material in the appropriate design.
  • Inspect the groove and stem, protect the seal from threads and sharp edges, and install without twisting. Use the compatible lubricant specified for the seal and service.
  • For example, Swagelok’s integral-bonnet needle valve kit supplies a replacement O-ring and backup ring. Use the assembly drawing to identify the lower gland, O-ring, backup ring and upper gland in the correct order, and use the kit’s specified lubricant and packing nut torque.
  • Replace soft seats only by the authorized method for that design. Some require shop service.

Opening and closing bonnets safely

Use the model instructions to determine the closure position, spring/actuator controls and how internal parts are retained. Before the final fasteners come off, support the bonnet and any parts it can carry. For example, the Fisher ET manual calls for a controlled separation with retained nuts to manage a stuck bonnet after depressurization and isolation. That step is for freeing the gasket joint under the manual’s procedure. Isolation and absence of hazardous pressure must already be verified.

Keep identification and orientation of the trim during inspection. Check the bonnet and body sealing surfaces, replace the specified gasket or seal, and use the prescribed bolting sequence and load. Verify travel and seat position as directed before reconnecting the actuator and restoring the valve to service.

Troubleshooting common leaks

Leak locationWhat you seeTypical corrective path
Stem / packingWet or vapor at glandDetermine whether isolation and inspection indicate gland adjustment, new packing or stem repair
Body-bonnet jointLeak at body/bonnet seamIsolate and verify before opening, then inspect surfaces and fit the specified new seal
End flanges / threadsLeak at pipe jointsGasket/bolt-up or thread seal issues (not packing)
Through-seat (pass)Downstream pressure rises with valve “closed”Debris on seat, worn seat/disc, bent stem, wrong valve for duty
Actuator connectionAir leak or stem coupling slipInstrument/mechanical coupling repair

Through-seat troubleshooting sequence:

  1. Verify closed travel or indication against the model’s allowable travel and seating force. Check whether bypasses or another source can pressurize the downstream side.
  2. Operations may authorize a controlled stroke and flush if permitted for the service. If leakage continues, identify the failed seat or trim under approved isolation.
  3. A passing valve cannot establish an effective boundary. Escalate for an alternate isolation. If a blind is required, verify safe first-break conditions with independent upstream isolation before installing it.
  4. Select authorized seat work, trim replacement or valve replacement, and verify leakage against the applicable acceptance criteria.

Sticking valves: Corrosion under packing, overtight packing, dried product on stems, thermal bind on high-temperature gates, and lack of lubrication on gear boxes. Free carefully after isolation—do not destroy the stem with unsafe cheater length.

When to replace vs repair

ConditionLean toward repairLean toward replace
Packing leak, good stemRepack—
Soft seat worn, body goodSeat kit if availableIf obsolete seat not available
Light seat wear, critical metal seatApproved shop work within the manufacturer’s limitsDamage beyond permitted restoration or an unavailable trim kit
Cracked body or severe wall lossRemove from service and obtain engineering dispositionReplace if the pressure boundary cannot be restored under an authorized engineering repair
Stem badly scored or bentStem/trim kit if offeredFull valve often cheaper/safer
Wrong type for service (gate used to throttle for years)—Replace with correct type
Rating or material inadequate for intended serviceEngineering review of service conditions and suitabilityUse a correctly specified valve when existing suitability cannot be established

After approved work, confirm controlled travel, pressure-boundary tightness and any required seat test. A shell test checks external containment, while a closure test checks leakage past the seat. Use the specified applicable test standard or manufacturer procedure. For B31.3-2024 construction, §345.2.6 calls for retesting affected piping after a repair or addition following its leak test, with a defined minor-work exception at the owner’s discretion when sound construction is assured. In-service repair uses the applicable owner, jurisdiction and post-construction requirements.

Preventive habits between outages

  • Exercise infrequently operated valves only on the approved schedule and with operations’ authorization.
  • Keep stems clean; restore protective coatings where specified
  • Inspect packing after major thermal cycles and hydro tests
  • Verify gear operator lubricant and handwheel integrity
  • Report passing isolation valves early so blinds can be planned for outages

Scenario: steam gate packing drip

A 6-inch steam gate begins leaking at the stem after startup. Report the leak and confirm the source from a safe position. With operations, plan isolation and verifiable depressurization before servicing the packing. Inspect the stem and gland, then fit the specified steam-service packing if the stem is within tolerance. Run the authorized travel and leak checks and monitor the stem after startup. If the stem is scored beyond limits, arrange repair or replacement before return to service.

Valve maintenance checks

  1. Secure isolating devices, render stored energy safe and verify before opening pressure boundaries.
  2. Diagnose leak location before changing parts at random.
  3. Repack and renew O-rings/seats with correct materials and clean surfaces.
  4. Support bonnets and internals and identify any spring load before separating them.
  5. Confirm an authorized repair or replacement meets integrity and service requirements, then complete the specified tests.
Test Your Knowledge

What must be completed before removing a valve bonnet for internal inspection?

A

Only paint a danger stripe on the handwheel

B

Secure process and actuator isolation, release or restrain stored energy, and verify safe conditions

C

Increase line pressure to blow debris out of the seat

D

Remove only half the bonnet bolts while the line remains at operating pressure

Test Your Knowledge

Why does an approved split-ring packing installation specify staggered joints?

A

To make the packing harder so it never needs adjustment

B

Because packing only seals if cuts face the flow arrow

C

To prevent a continuous leak path that would exist if all cuts aligned

D

To allow the handwheel to reverse operating direction

Test Your Knowledge

A block valve is verified fully closed. Its bypass is isolated and there are no other feeds. Upstream product appears at the isolated downstream side, where pressure rises. What is the most likely path?

A

Through the seat (valve not isolating internally)

B

Only at a painted surface far from the valve

C

At the nameplate rivets

D

Through a dry packing gland that shows no external moisture

Test Your Knowledge

Which condition most strongly supports replacing a valve rather than repairing it in place?

A

A single adjustable packing gland that needs a slight snug after heat-up

B

A dirty lever that needs cleaning and lubrication

C

A gear operator that needs grease per the maintenance schedule

D

A cracked valve body with deep erosive wall loss

Sections you finish are checked off in the contents.