6.4 Welding Processes, Prep & NDE
Key Takeaways
Recognize SMAW, GTAW, GMAW and FCAW from their electrodes and shielding. Use the process specified for each pass.
GTAW root with SMAW fill and cap is one qualified process combination. Use the WPS to verify the combination for the joint.
Use the applicable code, design and WPS for end preparation, fit-up, preheat, interpass control and PWHT.
The WPS gives production parameters. Qualification records establish the supported ranges. Welders and welding operators also need the applicable performance qualification.
VT checks visible conditions. PT shows flaws open to a suitably prepared surface. MT detects surface and near-surface flaws in ferromagnetic material. RT and UT have different volumetric capabilities and limitations.
Why pipefitters study welding and NDE
Pipefitters prepare and fit joints, verify dimensions, and help maintain access for welding and examination. The following process examples apply the 08207 butt-weld preparation skills. A fitter who makes production welds or tacks also needs the applicable qualification for that work.
Identify the welding process by its electrode and shielding. Then use the qualified welding procedure specification (WPS) and engineering design to check preparation, heat control and the stages at which the joint must be available for examination.
SMAW, GTAW, GMAW and FCAW
| Process | Electrode and shielding | Pipe applications and limits |
|---|---|---|
| SMAW (stick) | Consumable flux-coated rod supplies filler and shielding products | Portable for field work. Remove slag between passes and follow the electrode storage procedure. |
| GTAW (TIG) | Nonconsumable tungsten with inert gas shielding. Filler is separate when used. | Used for controlled roots and thin-wall work. Protect the shielding gas from drafts. |
| GMAW (MIG) | Continuous consumable wire with externally supplied shielding gas | Can give high deposition rates. Wire, gas, transfer mode and fit-up must suit the WPS and work conditions. |
| FCAW (flux-cored arc welding) | Continuous tubular flux-cored electrode, with either external gas shielding or self-shielding depending on the electrode | Useful for high deposition with suitable electrodes and procedures. Follow the wire’s shielding and slag-removal requirements. |
Miller’s multiprocess equipment manual distinguishes gas-shielded wire modes from self-shielded FCAW. Wire feed by itself does not identify a process. Welding processes are chosen and qualified for the material, joint and position.
Combination example. A piping WPS specifies a GTAW open-root pass followed by SMAW fill and cap. Check that the root prep, gas and any purge, each filler, and pass requirements match that WPS. The welder’s qualification must cover the applicable processes. Switch processes only under an approved procedure that covers the work.
Joint prep for welding
Prep quality is shared between fitter and welder:
- Correct bevel angle and land per WPS (see Section 6.1 for a single-V example).
- Root gap within tolerance all around.
- Hi-lo within limits.
- Cleanliness: remove oil, moisture, paint, rust, and cutting slag from the weld zone to the distance required.
- Tack welds per the qualified procedure. Under B31.3-2024 §328.5.1(c), qualified personnel make the tacks, root tacks use equivalent filler to the root pass, cracked tacks are removed and bridge tacks above the weld are removed.
Key Point: Verify the opening and alignment against the WPS and engineering design before welding. An unacceptable joint needs correction before the next operation.
Preheat and interpass temperature
Preheat brings the weld zone to a required minimum before welding, including tack welding when the code and WPS require it. On susceptible carbon and low-alloy steels, controlling cooling and allowing hydrogen to diffuse can reduce hydrogen cracking risk. More heat is not always better. Follow the limits in the approved WPS and applicable code. B31.3-2024 §330 gives preheat requirements, verification and allowances, and recognizes ASME B31P as an alternative.
Interpass temperature is checked before depositing the next pass. Use the WPS minimum and maximum as applicable. Check the required location and use an approved temperature-indicating method such as a temperature stick or calibrated contact instrument.
Worked example. The WPS for a carbon-steel weld requires a 200°F minimum preheat. Apply the approved heat source and verify the required zone is at temperature before tacking or welding. Recheck before the next pass if interpass limits apply. The 200°F value belongs to this example WPS.
PWHT — post-weld heat treatment
PWHT is a controlled thermal cycle after welding. Depending on alloy and procedure, it can reduce residual stress and temper hard regions of a weldment. Determine whether it is required from the design, material grouping, controlling thickness and applicable code/WPS. Under B31.3-2024 §331, use the applicable exemptions and permitted alternatives only when their conditions are met. The qualified cycle governs temperature, hold time and rates as applicable. Check thermocouple location and recording requirements before releasing a weld for the next operation.
WPS adherence
A Welding Procedure Specification (WPS) lists the production welding parameters. Under B31.3-2024 §328.2 and the applicable ASME Section IX, procedure qualification usually uses a procedure qualification record (PQR) documenting the coupon variables and test results. Section 328.2.1 also permits specified standard WPSs within the Section IX Article V limits. A welder’s performance qualification is a separate qualification. For production:
- Use only the process listed (do not swap GMAW for SMAW casually).
- Use the filler metal classification and sizes allowed.
- Respect positions, progression (uphill/downhill), and electrical ranges.
- Maintain preheat/interpass and any PWHT requirements.
- Follow joint design: backing, consumable inserts, open root, etc.
- If the joint cannot be made to the WPS (wrong gap, wrong material), stop and resolve—do not invent a field procedure.
Exam Tip: When an option says “whatever electrode is in the pouch” or “skip preheat if the metal feels warm,” treat it as wrong. Use the approved WPS and applicable engineering design and code.
NDE methods — capabilities and limits
Examination evaluates the work using the specified method. Under B31.3-2024 §§340–341, the owner’s Inspector verifies that required examination and testing have been completed. An indication is evaluated against the applicable acceptance criteria before it is classified as a rejectable defect.
| Method | What it can reveal | Practical limits |
|---|---|---|
| VT, visual examination | Accessible weld surfaces, profile and measurable fit-up or dimensions | Requires suitable light, viewing access and visual resolution. Buried flaws are outside its capability. |
| PT, liquid penetrant | Cracks or pores that open to the surface of a suitable nonporous material | Requires a clean surface and correct processing. A buried flaw cannot admit penetrant. |
| MT, magnetic particle | Surface and near-surface discontinuities in ferromagnetic material | Field direction matters. Use another method on nonferromagnetic material, such as a typical austenitic stainless base metal. |
| RT, radiographic examination | Radiation image showing differences in transmitted intensity, including many pores and slag inclusions | Crack detectability depends on orientation, thickness and technique. Control the radiation area. |
| UT, ultrasonic examination | Reflector responses from suitable probe and sound paths, including many internal planar discontinuities | Coverage depends on scan access, orientation, geometry and material. The procedure defines calibration and scanning. |
For B31.3-2024 Normal Fluid Service, §341.4.1(a)(3) requires visual examination of completed welds except those in components made to a listed standard. Section 341.4.1(b)(1) generally requires at least 5% random RT or UT of circumferential butt and miter groove welds within each designated lot, with the prescribed welder representation and permitted in-process substitution. For Category D, §341.4.2 calls for enough visual examination to satisfy the examiner that materials, components and workmanship conform. This is a different examination extent. The engineer may specify added coverage. Use the examination plan to identify the welds, method, extent and acceptance criteria.
Two method choices. An examiner looking for internal porosity might use RT if the weld geometry allows effective coverage. For a suspected surface-breaking crack in a suitably cleaned nonferromagnetic stainless socket fillet, PT is appropriate when the plan permits it. Visible checks can still be needed in both cases. Maintain access for examination. Follow the applicable radiation controls and repair and re-examination requirements.
Process selection snapshot for pipe
| Situation | Often seen process approach |
|---|---|
| Open-root process butt weld in the field | GTAW root, SMAW fill/cap (when WPS says so) |
| Shop weld with controlled shielding | Qualified GMAW where selected, or FCAW under its own procedure |
| Windy outdoor fill passes | SMAW often preferred over gas-shielded processes |
| Thin stainless sanitary or high-purity | GTAW-dominant procedures |
| Alloy weld with specified PWHT | Qualified welding process and required treatment cycle |
Common exam traps
- Calling GTAW “stick” or SMAW “TIG.”
- Believing GMAW needs no WPS because it is “just wire.”
- Confusing preheat with PWHT.
- Saying MT works the same on all stainless without magnetic considerations.
- Assuming RT replaces the visual-examination extent required for the weld.
- Ignoring that fit-up (gap, hi-lo, cleanliness) is part of welding quality.
Putting Section 6.4 together with Chapter 6
- 6.1 prepared the BW joint: bevel, land, gap, alignment, takeouts.
- 6.2 extended layout to miters, ordinates, and fabricated branches that still weld to a WPS.
- 6.3 powered the tools, lifts, and torque equipment around the weld.
- 6.4 closes the loop: choose and respect the process, control heat, obey the WPS, and understand how NDE will judge the result.
A pipefitter who owns fit-up and procedure discipline makes welders faster and NDE first-time-pass rates higher. That is the professional standard behind welding literacy on the Industrial Pipefitter path—and the practical payoff of studying SMAW, GTAW, GMAW, heat control, and examination methods as one system rather than isolated trivia.
A WPS calls for a nonconsumable tungsten electrode with inert gas on the root and a flux-coated consumable stick on fill and cap. Which processes does it specify?
GTAW root with SMAW fill and cap
GMAW root with GTAW fill and cap
SMAW root with FCAW fill and cap
FCAW root with GMAW fill and cap
What is the primary purpose of preheat before welding many carbon and low-alloy steel joints?
To replace the need for any filler metal classification on the WPS
To control initial temperature and cooling, reducing the risk of hydrogen cracking in susceptible steels
To post-heat the completed weld for residual stress relief after all passes are done
To magnetize the joint so MT can be skipped
Which NDE method is primarily used to detect internal volumetric discontinuities such as trapped slag or porosity inside a butt weld using radiation?
VT only
PT only
RT (radiographic testing)
MT only on non-magnetic materials
A welder wants to switch from the WPS-specified SMAW electrodes to a different process because wire feed is faster. What is the correct craft response?
Switch processes freely if the finished bead looks smooth
Switch only if the foreman prefers the appearance of MIG welds
Switch only on stainless steel; carbon steel has no WPS rules
Do not switch—weld only to the qualified WPS unless engineering provides a different approved procedure
Sections you finish are checked off in the contents.