3.1 Pipefitting Hand Tools

Key Takeaways

  • Module 08102 covers selecting, inspecting, maintaining and using hand tools for gripping, supporting, laying out, cutting, bending and joining pipe or tube.

  • Use a wrench rated for the work and the correct contact surface. RIDGID manual pipe wrenches require clearance behind the hook jaw and prohibit added leverage with a handle extension.

  • Select a rated vise and stand, fully engage its setup locks, and independently support long stock.

  • Layout tools—spirit levels, framing squares, wraparounds, and center finders—control fit-up quality before the joint is made permanent.

  • Clean and inspect tools before use. Remove damaged or worn components until repaired or replaced according to the manufacturer.

Last updated: November 2026

Pipefitting Hand Tools

Quick Answer: Module 08102 expects you to select the right pipe wrench, stand, vise, level, square, wraparound, center finder, tube cutter, bender, or joining tool, inspect it before use, maintain it, and apply it safely. Good fit-up starts with tools that grip, hold, mark, and cut without damaging the pipe or the worker.

The Pipefitting Fundamentals domain on the Industrial Pipefitter journey assessment (PFT08_03) is 15 items (12%), drawn from modules 08102 (hand tools), 08103 (power tools and threading), and 08303 (standards, codes, and specs). This section builds the hand-tool foundation every later fabrication task assumes.

Why hand tools still matter

Power threaders and grinders dominate production shops, but hand tools remain daily equipment for:

  • Breaking and making threaded joints in tight racks
  • Clamping and supporting pipe for cutting or welding
  • Checking level, plumb, and square before permanent joinery
  • Laying out holes, branches, and cut lines on round pipe
  • Flaring and cutting soft tubing where machine tools will not fit

Assessment items often describe a task ("tighten a 2-inch threaded coupling overhead" or "mark a circumferential cut line") and ask which tool, jaw position, or inspection step is correct.

Pipe wrenches

A straight pipe wrench grips round pipe between serrated heel and hook jaws. Use the RIDGID Pipe Wrench Use Guide or the instructions for the actual tool.

PracticeReason
Choose a tool and size rated for the workThe tool must fit the round surface and carry the applied load
Seat the heel and hook teeth, with space behind the hook-jaw shankBoth teeth must engage. The back of the hook must have clearance for the wrench to grip under load.
Apply steady hand force with stable footing and the handle in the correct turning directionThis keeps the load controlled if the joint releases or the wrench slips
Hold the stationary side with a backup wrench on a suitable wrenching surfaceThis avoids transferring torque into attached pipe or equipment

Offset and end wrenches can provide access near walls. A chain wrench can grip eligible larger round stock within its rating. A strap wrench protects suitable finished surfaces. Use the appropriate wrench for hex flats and check the instructions for plastic or thin-wall tubing, which can be damaged by concentrated force.

RIDGID prohibits extensions, impact blows and using a powered device to drive its manual pipe wrench. For greater torque choose a larger rated tool, a purpose-built compound leverage wrench or another approved method for the joint. Keep a hand on the wrench to prevent it from falling.

Stands and vises

Pipe must be held solidly for cutting, reaming, threading, and assembly.

Pipe stands (tripod / chain stands)

Tripod stands with chain vises or yoke vises support horizontal pipe within their rated capacities, as shown in the RIDGID TRISTAND instructions. Setup rules:

  1. Place the stand on firm, level ground or decking
  2. Spread legs fully and lock any folding hardware
  3. On an adjustable model, set the working height within its limits. Use any specified stabilizing device.
  4. Center the pipe in the vise jaws or chain; tighten until the pipe cannot rotate under cutting or threading torque
  5. Use additional rated supports where needed to carry the overhang and keep the work stable

Yoke vises vs chain vises

FeatureYoke viseChain vise
Grip styleA yoke-mounted screw advances the upper jaw against the stationary jawChain wraps the circumference
Best forCommon NPS sizes within jaw rangeLarger diameters and some irregular shapes
Damage riskJaw teeth can mark soft materialsChain can mark if dirty or overtightened
Typical useShop and stand-mounted workField stands and larger stock

Keep vise teeth clean of metal chips and pipe dope. Worn or rounded teeth slip under load—replace jaws rather than overtighten until the pipe collapses.

Bench vises and specialty holders

Bench-mounted vises hold fittings, short nipples, and fabricated pieces. Use a compatible vise with approved soft jaws or protectors for finished surfaces. Never clamp thin-wall tube so hard that you oval it before flaring or soldering.

Levels and squares

Spirit (bubble) levels check horizontal and vertical alignment of pipe runs, hangers, and equipment nozzles. Practices:

  • Clean the pipe surface so the level seats true
  • Read the bubble with your eye centered over the vial
  • Check level in two planes when hanging a header (slope for drainage is intentional—do not "level" a line that drawings require to pitch)
  • Protect vials from impact; a cracked or separated vial is out of service

Framing squares and combination squares establish right angles for hanger layout, support steel, and square cuts on plate. On round pipe, a square alone does not wrap the circumference—pair it with wraparound layout for cut lines.

Torpedo levels fit in tight spaces. A magnetic model can attach to a suitable steel surface for a check of plumb or level.

Wraparounds and layout on round pipe

A wraparound is a flexible layout tool. Align the overlapping edges around the outside of the pipe before marking a square circumferential cut. A straight edge of the tool can help transfer reference marks. Uses include:

  • Squaring a cut line before sawing or oxyfuel cutting
  • Transferring an axial reference mark along the pipe surface
  • Aligning branch marks for saddles and laterals (with templates or ordinate methods covered in advanced fabrication)

Center heads help locate the center of a circular end or establish a clock position on a pipe surface, depending on the tool. Transfer corresponding marks onto the pipe for a straight axial reference before laying out the opening or branch.

Layout sequence common in training:

  1. Clean and, if needed, white-paint or soapstone a readable surface
  2. Establish a longitudinal reference line with wraparound or straightedge
  3. Mark circumference or hole pattern from that reference
  4. Verify measurements twice before cutting

Flaring tools and tube cutters

Soft copper and some thin-wall tubing systems use flared or cut-and-join methods that differ from steel pipe threading.

Tube cutters

Tube cutters score and sever tubing with a cutting wheel advanced by a knob as you rotate the tool around the tube. Good practice:

  • Select a cutter sized for the tube OD
  • Advance the wheel in small increments as the cutter rotates. Excessive feed can deform the tube end.
  • Use the specified cutter wheel for the material
  • Ream or deburr the ID so the burr does not restrict flow or damage ferrules and flares

Flaring tools

Flaring tools form the flare that seats against the fitting. For a specified SAE 45° joint, use a compatible 45° tool and tubing within its rated material and wall limits. Hydraulic fittings can use a different angle such as 37°. Match the specified tube, tooling, nut and fitting seat. For the 45° copper example:

  1. Cut square and deburr
  2. Slip the matching flare nut onto the tube in the correct direction before flaring
  3. Clamp the tube in the correct die size with the proper projection above the die face
  4. Drive the flaring cone to form a full, even flare without splitting
  5. Inspect for cracks, uneven skirts, and undersize/oversize flares

Inspect flare size, shape and surface against the fitting instructions. Reject a cracked or uneven flare. If the remaining tube length permits, cut off the defect and form a new end. The Copper Tube Handbook describes the copper flare sequence.

Hand bending and joining

Choose a hand bender with a form rated for the tube OD, material, wall and bend radius. On the RIDGID 600 series, identify the appropriate measuring mark and clamp the tube against the form. Make the bend with the model’s angle scale, then check the released angle and condition. Tubing can spring back after release. Check for kinks, flattening and an incorrect bend plane before joining.

Match the joining tool to the connection. For example, Viega ProPress instructions specify the compatible press tooling and the insertion depth mark. A flare uses the correct cone and dies and the matching fitting seat. For a threaded pipe joint, use the rated wrenching surfaces described above.

Selection, inspection, maintenance, and safety

Maintain hand tools in safe condition. Federal OSHA addresses unsafe hand tools under §§1926.300(a) and .301 in construction and employer responsibility under §1910.242(a) in general industry.

Selection checklist

TaskPreferred tool family
Tighten/loosen steel threaded pipePipe wrench sized to OD
Protect chrome or plasticStrap wrench
Hold pipe for thread/cutStand with chain or yoke vise
Check run for true horizontal/verticalSpirit level (respect drawing slope)
Mark square cut on round pipeWraparound + soapstone/marker
Locate axis / equal divisionsCenter finder / center head
Cut soft tubingTube cutter + reamer
Prepare flared copper jointCorrect die flaring tool

Inspection before each use

Remove from service if you find:

  • Rounded or chipped wrench teeth. Clean contaminated teeth before reinspecting them.
  • Cracked castings, bent handles, or loose jaw pins
  • Vise chain links that are stretched, cracked, or missing
  • Level vials with separated liquid, cracks, or illegible graduations
  • Tube-cutter wheels that are flat, nicked, or seized
  • Flaring cones that are galled or dies that are out of round

Maintenance

  • Clean chips and sealant from jaws and die seats
  • Lightly oil pivot points; wipe excess so handles are not slippery
  • Store wraparounds flat or rolled without creasing grid lines beyond use
  • Replace damaged or worn cutting wheels and reamer blades with the specified parts
  • Keep tool bags organized so sharp edges do not cut soft tools or cords

Safety

  • Wear eye protection when cutting, reaming, and breaking seized joints (scale and chips fly)
  • Keep hands clear of pinch points at vise screws and wrench jaws
  • Use a stable working surface and stay clear of the handle’s travel if the joint breaks free
  • Secure stands so vibration from threading does not walk them off the edge
  • Support and handle long or heavy pipe with equipment rated for the load

Scenario: breaking out a threaded union

A painted 3-inch threaded union in a rack needs removal. Verify the line is isolated, depressurized and safe to open under the line-opening procedure, and check that both sides are supported. Select the wrench for the union nut’s actual shape and intended wrenching surface. Hold the stationary part with a backup wrench where specified. Apply steady force from stable footing and out of the handle’s travel path. If the union remains seized, arrange an approved removal method within the equipment limits.

Putting Module 08102 together

  1. Select the tool that matches material, size, and surface finish.
  2. Inspect jaws, handles, vials, wheels, and chains before use.
  3. Secure the work in a proper stand or vise before cutting or threading by hand.
  4. Lay out with wraparounds, squares, levels, and center finders so cuts and holes land true.
  5. Maintain tools so the next joint is as good as this one.

Master these habits and power tools, materials knowledge, and code work in the next sections rest on a solid foundation—literally the tools in your hands.

Test Your Knowledge

When breaking a threaded pipe joint, why is a second (backup) wrench commonly required?

A

To measure the exact thread engagement length on the pipe

B

To hold the fitting or adjoining pipe so torque does not twist the wrong component

C

To replace the need for any pipe stand or vise on long runs

D

To convert a strap wrench into a chain vise for large diameters

Test Your Knowledge

What is the primary purpose of a wraparound when preparing to cut round pipe?

A

To increase the torque capacity of a straight pipe wrench

B

To ream the inside diameter after the cut is complete

C

To mark a true circumferential or reference line on the pipe outside diameter

D

To form a 45-degree flare on soft copper tubing

Test Your Knowledge

A square-cut, deburred copper tube is ready for a specified single 45° flare. What must be in place before the cone forms the flare?

A

No nut until the flare is finished

B

The matching flare nut already slid onto the tube in the correct orientation

C

The cutting burr saved inside the tube as a seat

D

A pipe wrench clamped tightly onto the tube OD

Test Your Knowledge

Which condition should remove a straight pipe wrench from service?

A

Hook-jaw teeth that are rounded and chipped

B

A handle that is the correct length for the pipe size being turned

C

Clean, sharp jaw teeth that match the pipe outside diameter

D

A wrench used only for its designed pipe-turning purpose

Sections you finish are checked off in the contents.