Safety
12%of exam
Math
12%of exam
Pipefitting Fundamentals
12%of exam
Cutting
8%of exam
Fabrication
16%of exam
Construction Drawings
10.4%of exam
Rigging
6.4%of exam
Valves, Hangers, and Supports
11.2%of exam
Pipefitting Specialties
12%of exam
Quick Facts
- Assessment
- Industrial Pipefitter PFT08_03
- Level
- Journey-level knowledge assessment
- Written items
- 125
- Time and format
- 3 hours, closed book
- Minimum passing score
- 75
- Allowed reference
- The Pipefitters Blue Book
- Allowed calculator
- Non-programmable, non-printing
- Calculator types
- Basic, scientific, or pipe-specific
- Other study materials
- No extra notes or books
- Full craft certification
- Knowledge assessment + performance verification
- Curriculum
- Pipefitting, 4th edition
- Blueprint revision
- November 2024
Hydrostatic vs Pneumatic
Hydrostatic
- Liquid test medium
- Vent trapped air during fill
Pneumatic
- Gas test medium
- Higher stored energy risk
Test to the approved plan
Safety Checks
- Portable ladder has damaged rung→Withdraw it from service
- Shift starts on scaffold→Competent person inspects
- Excavation exposed to rain→Competent person reinspects
- Approved hydro test filling→Vent trapped air(At high points)
- Liquid medium unsuitable→Use approved test plan(Pneumatic needs added controls)
Access and Excavations
- Typical leaning ladder
- Base setback ≈ ¼ working length
- Damaged portable ladder
- Mark and withdraw from service
- Scaffold inspection
- Competent person before each shift
- Before excavating
- Determine estimated utility locations
- Trench after rainstorm
- Competent person reinspects
- Shoring
- Supports excavation walls
- Shielding
- Protects workers within shield
- Sloping
- Cuts trench walls back
Pressure Test Setup
- Test boundary
- Defines isolated test segment
- Hydrostatic test
- Uses liquid, usually water
- Pneumatic test
- Uses compressed gas
- High-point vent during hydro fill
- Releases trapped air
- Test pressure and duration
- Use governing code and approved plan
- Test gauge
- Check calibration and range
Set, Roll, Then Travel
Square both shifts, root, then divide by sine.
Offset Calculator
- Offset stays in one plane→Use perpendicular offset directly
- Line shifts vertically and sideways→√(set² + roll²)(Find true offset first)
- Given travel angle and offset→Offset ÷ sin θ(Use true offset)
- Need run along original axis→Offset ÷ tan θ(Use true offset)
- Equal 45° offset fittings→True offset × 1.414(Center-to-center travel)
Offset Geometry
- True rolling offset
- √(set² + roll²)
- Center-to-center travel
- True offset ÷ sin θ
- Run along original axis
- True offset ÷ tan θ
- 22.5° travel multiplier
- ≈ 2.613 × true offset
- 30° travel multiplier
- 2 × true offset
- 45° travel multiplier
- ≈ 1.414 × true offset
- 60° travel multiplier
- ≈ 1.155 × true offset
- Set 6″, roll 8″
- True offset = 10 in
- 10 in offset at 45°
- Travel ≈ 14.14 in
Layout Formulas
- Offset angle θ
- Between travel and original run
- Rise or fall
- Horizontal run × slope ratio
- Pipe outside circumference
- π × outside diameter
- Inside diameter (ID)
- OD − 2 × wall thickness
- Degrees on calculator
- Use degree mode
NPS vs Schedule
NPS
- Nominal size designation
- Look up actual OD
Schedule
- Wall-thickness series
- Look up wall by NPS
Specify both size and schedule
Hand and Power Tools
- Pipe wrench
- Turns round threaded pipe
- Strap wrench
- Grips polished pipe without teeth
- Pipe vise
- Holds pipe during fabrication
- Reamer
- Removes internal cut burr
- Threading die
- Cuts external pipe threads
- Pipe stand
- Supports stock during fabrication
Pipe Dimensions and Standards
- NPS
- Nominal Pipe Size
- Pipe schedule
- Wall-thickness series by size
- OD
- Measured outside diameter
- Same NPS, thicker wall
- Smaller inside bore
- ASME B31.3
- Process piping code
- WPS
- Welding procedure specification
Oxyfuel Cutting
- Preheat flame
- Raises steel to ignition temperature
- Cutting oxygen
- Oxidizes steel and ejects slag
- Ordinary oxyfuel cutting
- Suitable for carbon steel
- Regulator
- Controls gas delivery pressure
- Kerf
- Width of material removed
- Oxygen equipment
- Keep free of oil and grease
Field Routing
- Field cut
- Verify actual tie-in dimensions
- Routing check
- Confirm clearances and support locations
- Vessel trim
- Piping and fittings at vessel
- Prepared weld bevel
- Check approved joint detail
Butt Weld vs Socket Weld
Butt weld
- Opposing ends align
- Check specified root opening
Socket weld
- Pipe enters socket
- Check specified back-off gap
Follow the approved joint detail
Fit-Up Decisions
- Given center distance between fittings→Subtract both center-to-face dimensions
- Given clear faces, butt welds→Subtract both specified root gaps
- Given clear faces, threaded joints→Add both specified thread engagements
- Socket weld fit-up→Check insertion and specified gap
- Bevel angle or root gap→Check approved weld procedure(Use applicable joint detail)
Joint Types
- Butt weld
- Joins aligned pipe ends
- Socket weld
- Pipe inserts into fitting recess
- Socket weld fillet
- Around socket mouth
- Socket weld fit-up
- Leave specified insertion gap
- NPT
- Tapered American pipe thread
- Thread engagement
- Length inserted into threaded fitting
- Thread sealant
- Match fluid and service conditions
Takeouts and Fit-Up
- Center-to-face dimension
- Fitting centerline to end face
- Clear face-to-face gap
- Center distance − both center-to-face dimensions
- Butt-weld cut length
- Face distance minus both root gaps
- Threaded cut length
- Face distance plus both engagements
- Takeout lookup
- Use exact fitting dimensions
- Hi-lo
- Internal offset at joint
- Miter turn
- Angled cuts form the bend
- Saddle layout
- Template matches intersecting pipe contour
Line, Legend, Dimensions
Trace the line, read the legend, trust dimensions.
P&ID vs Isometric
P&ID
- Process connections and flow
- Instrument tags and signals
Isometric
- Spatial pipe routing
- Fabrication dimensions and elevations
Trace flows on the P&ID
Drawing Picker
- Trace process flow and controls→P&ID
- Locate equipment in plant→General arrangement
- Find elevations and offsets→Piping isometric
- Fabricate one numbered assembly→Spool drawing
- Count fittings for spool→Bill of materials
Pipe Drawings
- P&ID
- Piping and instrumentation diagram
- Instrument signal line
- Shows control or measurement connection
- General arrangement
- Shows equipment placement and routing
- Piping isometric
- Shows spatial routing and dimensions
- Spool drawing
- Details one fabricated pipe assembly
- Bill of materials
- Lists components and quantities
- Elevation
- Height relative to project datum
- Continuation reference
- Follow line onto another sheet
Vertical vs Basket Hitch
Vertical
- Single straight sling leg
- Use vertical hitch rating
Basket
- Both sling ends support load
- Use rated basket configuration
Read hitch and angle rating
Lift Checks
- Sling identification missing→Remove equipment from service
- Sling angle becomes flatter→Recheck rated configuration
- Sharp edge contacts sling→Use suitable edge protection
- Emergency stop signal received→Stop the lift
Hitches and Sling Loads
- Vertical hitch
- Single straight sling connection
- Basket hitch
- Sling cradles load from underneath
- Choker hitch
- Sling cinches around load
- Flatter sling angle
- Higher leg tension, same load
- Sling tag
- Check rated configurations
- Defective rigging
- Remove from service
- Sling over sharp edge
- Protect sling from edge damage
- Emergency stop
- Obey regardless of signaler
Isolate, Regulate, Check
Gate isolates, globe regulates, check blocks backflow.
Gate vs Globe
Gate
- Typical isolation duty
- Normally fully open or shut
Globe
- Typical regulating duty
- Suitable trim for throttling
Choose by duty and service
Valve and Support Picker
- Typical line isolation needed→Gate valve(Check service specification)
- Typical throttling needed→Globe valve(Check service specification)
- Backflow prevention needed→Check valve(Verify flow arrow)
- Automatic overpressure protection needed→Specified relief device
- Limit sideways pipe drift→Specified guide
- Support pipe through vertical travel→Specified spring hanger
Valve Functions
- Gate valve
- Typical on-off isolation
- Globe valve
- Typical throttling service
- Check valve
- Closes against reverse flow
- Check valve flow arrow
- Matches intended flow direction
- Relief valve
- Opens at set pressure
Guide vs Anchor
Guide
- Permits designed axial travel
- Limits lateral movement
Anchor
- Fixes pipe at design point
- Transfers restraint forces to structure
Check the support detail
Support and Movement
- Clevis hanger
- Suspends pipe from structure
- Rest support
- Carries downward pipe load
- Guide
- Restrains lateral movement
- Anchor
- Restrains pipe at fixed point
- Spring hanger
- Carries load during vertical travel
- Pump nozzle
- Observe allowable piping loads
Grooves Grip, Gasket Seals
Housing grips grooves, gasket seals the joint.
Soldering vs Brazing
Soldering
- Filler liquidus below 450°C
- Copper base metal stays solid
Brazing
- Filler liquidus above 450°C
- Copper base metal stays solid
Compare filler metal liquidus
In-Line Devices
- Steam trap
- Discharges condensate, limits steam loss
- Drip leg
- Collects condensate for drainage
- Strainer
- Screens debris from flow
- Thermowell
- Protects temperature sensor
- Expansion joint
- Accommodates specified pipe movement
- Desuperheater
- Lowers superheated steam temperature
Installation and Special Joints
- Buried pipe bedding
- Provides uniform support
- Haunching
- Supports lower sides of pipe
- Flanged joint gasket
- Seals between mating faces
- Grooved coupling
- Housing engages grooves, gasket seals
- Copper soldered joint
- Lower-temperature capillary filler
- Copper brazed joint
- Higher-temperature capillary filler
Common Traps
Excavation protection
Shoring supports trench walls ≠ Shielding shelters workers
Offset geometry
True offset across runs ≠ Travel between fitting centers
Dimensional labels
Nominal pipe size designation ≠ Measured outside diameter
Cut layout
Kerf width removed ≠ Bevel angle created
Fit-up dimensions
Fitting center-to-face dimension ≠ Thread engagement into fitting
Drawing scale
Isometric drawn appearance ≠ Verified written fabrication dimension
Rigging capacity
Sling tension per leg ≠ Total load weight
Steam line devices
Steam trap discharges condensate ≠ Strainer catches debris
Last Minute
- 1.Fabrication carries 20 written items
- 2.Blue Book allowed during assessment
- 3.Hydro test filling vents air
- 4.Roll and set combine perpendicularly
- 5.45° travel ≈ 1.414× true offset
- 6.Size and schedule determine wall thickness
- 7.Allow for both butt-weld root gaps
- 8.P&ID traces flow and instrumentation
- 9.Flatter sling angles raise leg tension
- 10.Gate isolates, globe throttles
- 11.Guides allow designed axial movement
- 12.Steam traps discharge condensate
Explore More NCCER Certifications
Continue into nearby exams from the same family. Each card keeps practice questions, study guides, flashcards, videos, and articles in one place.
More From This Family
Videos and articles for deeper review.
