10.1 Pipe Hangers & Supports

Key Takeaways

  • Identify the load that each support carries and trace it through each attachment into approved structure.

  • Use the specified hanger, clamp, rod, turnbuckle and beam attachment with their approved mounting, loading and adjustment limits.

  • A guide permits specified travel and resists displacement in the specified directions. An anchor, operational stop and temporary spring lock perform different jobs.

  • Check both the load and travel range of a variable or constant spring. Follow the manufacturer and test plan to set and release temporary stops.

  • Size and place supports for actual gravity and operating loads, including the test medium and concentrated equipment loads.

Last updated: November 2026

Pipe Hangers & Supports

Quick Answer: Hangers and supports carry weight, control movement, and transfer load into approved structure. Module 08308 covers clevises, saddles, U-bolts, clamps, turnbuckles, rods, welded beam attachments, spring cans, travel stops and snubbers. Check each assembly’s support or restraint direction, loads, location and travel.

The journey assessment domain Valves, Hangers, and Supports includes Module 08308 hangers and supports (part of the 14 items shared by Modules 08203, 08308 and 08403 on the PFT08_03 blueprint). This section builds the hardware and layout foundation for every elevated and rack-mounted run.

Why supports matter as much as joints

The same pipe can be much heavier during hydrostatic testing than in gas or steam service. For example, an NPS 8 Schedule 40 steel pipe has 8.625 in. OD, 0.322 in. nominal wall, and 28.58 lb/ft nominal plain-end weight in ASME B36.10-2022 Table 2-1. Its calculated ID is 7.981 in. At 62.4 lb/ft³, the water weight per foot is π ÷ 4 × (7.981 ÷ 12)² × 62.4 ≈ 21.68 lb/ft. With an assumed 2 lb/ft of insulation and jacket, a 20-ft piece weighs about 1,045 lb when filled, before adding fittings or valves. This is total piece weight. Actual reactions depend on support layout, stiffness and other loads, so use the support schedule and test plan. Without adequate support:

  • Pipe sags and creates low points that collect liquid or deposits
  • Flanges and welds see bending stress they were not designed for
  • Equipment nozzles take pipe weight that belongs on hangers
  • Thermal growth jams into fixed equipment and rack steel
  • Vibration and water hammer move lines until something breaks or leaks

Pipefitters fabricate and erect supports, set elevations, adjust rods and turnbuckles, install spring cans per load tables, and report missing or overloaded steel. Assessment items often show a support type and ask its purpose—or describe sagging pipe and ask what is wrong with spacing or hardware.

Roles of pipe supports

Supports do more than “hold the pipe up.” Design and craft practice assign distinct roles:

RoleWhat it doesTypical devices
Weight support (gravity)Carries dead load of pipe, fluid, insulation, and valvesClevis hangers, trapeze, shoes on beams, stanchions
GuidePermits the specified travel and limits movement in designated directionsAxial guides, guided shoes, detailed U-bolt assemblies
AnchorRestrains displacement at a defined location and transmits the designed reactions into structureEngineered anchor assemblies
Operating limit stopEngages after the specified gap closes or limits travel in the specified directionStops on a shoe or other engineered restraint
Dynamic controlProvides designed resistance to a specified transientHydraulic or mechanical snubbers
Variable supportSupports weight while spring force changes with travelVariable spring hangers (spring cans)
Constant supportKeeps support force substantially uniform through its rated travelConstant-effort spring hangers (advanced systems)

Key Point: Installing every support as a rigid clamp “so it won’t move” can overstress the system. Some movement is designed; guides and springs are not optional decorations.

Common hanger and support hardware

Clevis hangers

A clevis hanger is a U-shaped strap or yoke that cradles the pipe (often with a saddle or spacer) and hangs from a rod through a clevis pin or bolt. Uses:

  • Horizontal runs of steel and other metallic pipe
  • Gravity support with limited movement, subject to the hanger and connection details
  • Easy elevation adjustment by turning the rod/nut assembly where designed for adjustment

Installation notes:

  • Match the clevis and shield to the pipe OD and insulation detail. Assemble with the specified orientation, fasteners and clearance.
  • Protect coated or insulated pipe with specified shields/saddles so the metal strap does not cut the jacket

Saddles and wear pads

Saddles, wear pads and insulation shields spread a local load according to the support detail. On insulated lines, size the shield and load-bearing insert to carry the weight without crushing insulation. On a high-temperature run, use the specified sliding and attachment surfaces, accounting for local stress, temperature and movement. Correct conflicting elevations without omitting required support hardware.

U-bolts

U-bolts clamp pipe to a structural member or support frame. They may be:

  • Clamped to serve a specified restraint function if the complete assembly is rated for the load
  • Guided, with nuts secured at the specified clearance or spacers so the pipe can slide as designed

Check the detailed restraint directions and ratings. Tightening an ordinary U-bolt does not establish an engineered anchor.

Misuse patterns:

  • Crushing thin-wall or plastic pipe with overtorqued nuts
  • Creating unintended anchors that fight expansion loops
  • Omitting liners or pads on copper, stainless, or coated lines when specified

Clamps

Pipe clamps (two-bolt, three-bolt, riser clamps, beam clamps for attachments) grip the pipe or the structure:

Clamp typeTypical use
Two-bolt / three-bolt pipe clampSuspended support from rods; riser and horizontal applications per design
Riser clampTransfers vertical load of a riser to a floor or steel at designated levels
Beam clamp (attachment)Connects rod or hardware to a structural beam flange when welding is not used

Riser clamps must sit on designed bearing surfaces—not on grating that can punch through or on random angle iron without capacity checks.

Rods and turnbuckles

Hanger rods carry tension from the pipe attachment up to the structure. Turnbuckles provide length adjustment in the rod assembly.

Craft practices:

  • Use rod diameter and material specified or matched to load tables—do not substitute smaller all-thread from the gang box
  • Verify thread engagement for each part. For B31.3 supports, §321.1.5 requires the full internal thread length of turnbuckles and adjusting nuts to be engaged.
  • Leave adjustment room in turnbuckles; do not run them fully closed or fully open as a permanent condition if the design expects mid-range adjustment
  • Secure threaded adjustments with the specified locking method. B31.3 §321.1.5 requires a locknut unless the adjustment is locked by other means.
  • Set rod position to the drawing. A designed cold offset can account for thermal swing. Verify the allowable angular movement and attachments rather than moving the rod to an arbitrary plumb position.

Welded beam attachments

Welded beam attachments (lugs, clips, ear plates, manufactured weld-on attachments) fix the top of the hanger to structural steel.

Rules of the craft:

  • Weld only to approved locations and members—structural engineers own where you may weld on building steel
  • Use the approved WPS for the substrate and attachment. When an integral attachment is welded to B31.3 piping, §321.3.2 points to the piping fabrication requirements for welding, preheat and heat treatment.
  • Do not weld to joists, thin deck, or fireproofing-covered steel without authorization
  • Locate the attachment where the support drawing puts the planned load and movement line
  • After welding, clean slag and inspect per site quality requirements before loading

Beam clamps or bolted attachments may replace welding when the design or owner forbids field welds on structure.

Spring supports and travel

A variable spring changes its supporting force as it compresses or extends. A constant support uses a mechanism that compensates for changing spring force and gives a nearly uniform load over its rated travel. Selection depends on the operating load, the magnitude and direction of travel, and the acceptable load change at the pipe and adjacent equipment.

Worked selection check. The support schedule requires 1,000 lb hot support force and 2 in. upward travel. For a suspended variable spring with a 100 lb/in. rate that unloads as the pipe rises, the cold load is 1,200 lb and the load change is 200 lb, or 20% of the hot load. That meets a specified 25% variation limit such as the recommendation illustrated in PT&P’s variable spring sizing guidance. The can still needs rated travel and cold/hot loads that both fall within its usable range. A more sensitive nozzle or a smaller permitted load change may require a different spring or a constant support.

At installation check the tag and cold indicator against the drawing. Verify the hot indicator at operating conditions. Follow the manufacturer’s load-transfer procedure and approval sequence for temporary pins or blocks.

Operating stops and temporary spring locks

An operating stop remains in place to limit travel in a defined direction, commonly after a specified gap closes. A temporary spring lock secures the mechanism for shipping, erection or a test when the design permits. For PT&P’s illustrated spring installation, the stop is removed after any applicable hydrotest and the specified load transfer. For an installed bellows, follow its separate shipping-restraint procedure in Section 10.3. Do not force a loaded pin. If it binds, stop and verify the setting and support loads with the responsible team. Check temporary support capacity whenever the hydrostatic load case exceeds the operating support load.

Snubbers

A structural snubber permits gradual thermal displacement and resists specified rapid motion such as a seismic or transient load. A hydraulic model can activate at a prescribed piston speed. A mechanical model can respond to acceleration with a braking force. Each device has model-specific activation, drag, load and travel limits.

Check the specified orientation, pin-to-pin length, stroke remaining in both required directions and attachment geometry. Check for fluid leaks on hydraulic units and report binding, damage or a wrong setting. Use the approved inspection and functional test. A structural snubber carries the transient through its attachments into structure. An instrument pressure snubber instead dampens pulsation at a gauge connection.

Rigid vs flexible support concepts

CategoryBehaviorWhen used
Rigid weight supportCarries load without intentional spring travel in the supported directionA rigid shoe may still slide axially or transversely as detailed
Flexible (spring)Controlled displacement under changing temperature/loadHot lines with significant vertical travel
GuidedFree in one direction (often axial), restrained in othersAlong expansion runs between anchors
Dynamic restraintA snubber responds to a transient. A rigid strut constrains movement along its own axis.Use the device and direction specified by the design.

Check which axes are restrained. A support intended to carry weight can also transmit unintended loads if the slide or guide binds.

Spacing concepts

Support spacing (span) depends on:

  • Nominal pipe size and wall thickness
  • Material modulus and allowable deflection/stress criteria
  • Contents density (gas vs liquid) and test medium weight
  • Insulation and cladding weight
  • Concentrated loads (valves, fittings, specialties)
  • Applicable code and engineering design. MSS SP-58 covers support selection, application and installation.

ASME B31.1-2024 Table 121.5-1 gives suggested maximum spans for the table’s straight horizontal standard or heavier steel pipe applications, up to 750°F. The table assumes the stated fixed-beam loading, insulation and allowable sag and excludes spans with concentrated loads or separately calculated spans. For NPS 2, the table gives 10 ft in water service and 13 ft in steam, gas or air service. These are code-table examples under their stated conditions. For process piping, use the applicable engineered spacing and support detail under B31.3 §321. A valve between supports or a planned hydro fill on a gas line can change the support requirements.

General craft habits:

  1. Place supports per isometric and support detail locations—not only “every so often by eye”
  2. Add supports near heavy valves and changes in direction when the design shows them
  3. Do not increase spans to save hangers without engineering approval
  4. Temporary construction supports must be planned so the line is never left hanging on a single questionable weld or flange
  5. Verify test supports and hardware positions before filling. After draining, follow the commissioning plan for transferring the load and releasing any temporary restraints.

Load paths

Every pound of pipe weight travels a load path:

Pipe wall → saddle/clamp/clevis → rod or shoe → attachment → structural beam/column/foundation

If any link is missing, undersized, or attached to non-structural material (thin duct, cable tray, random handrail), the load redistributes to neighboring supports, flanges, or equipment nozzles—often the failure point.

Field checks for a sound load path:

  • Attachment is on structure, not on process pipe used as a “beam” for another line unless specifically engineered for the combined load
  • Hardware grade and size match the bill of materials or standard detail
  • Rods are not bent around obstacles in a way that side-loads threads
  • Baseplates and stanchions bear on grout/steel as detailed
  • Fireproofing or insulation does not hide a disconnected lug

Scenario: hot header on spring cans

The test plan leaves the temporary locks fitted to variable spring hangers on a steam header. After draining, the turnover crew finds one lock still carrying load and unable to release freely. Hold startup. Check the installed pipe elevation, spring tag, cold mark and adjacent supports against the design and follow the manufacturer’s procedure for transferring the load. Once the temporary locks are safely released, confirm clear travel and record the cold marks. At operating temperature verify the indicators reach the expected range without topping or bottoming out.

Putting Module 08308 hangers together

  1. Know the role of each support: weight, guide, anchor, spring, snubber.
  2. Select and install clevis, saddle, U-bolt, clamp, rod, turnbuckle, and beam attachment hardware per detail.
  3. Release temporary spring locks as specified, and retain operating stops with their designed gaps.
  4. Respect spacing and load path into real structure.
  5. Never create unintended anchors that fight designed thermal movement.
Test Your Knowledge

What is the primary operating purpose of a variable spring can hanger on a hot process line?

A

To permanently lock the pipe against all vertical movement during operation

B

To support pipe weight while allowing controlled vertical travel as temperature changes

C

To replace the need for any anchors or guides in the system

D

To increase hydrostatic test pressure by preloading the pipe

Test Your Knowledge

A test plan kept temporary spring-hanger locking pins in place for hydrostatic testing. What should the crew do before hot service?

A

Leave the stops engaged permanently so the spring cannot move

B

Weld the stops to the can body so vibration cannot loosen them

C

Remove or release the temporary travel stops per procedure so the hanger can travel in service

D

Replace the spring can with a rigid clevis after the first heat cycle without engineering input

Test Your Knowledge

Which description best matches a snubber’s role compared with a rigid strut or a spring weight hanger?

A

It only carries steady gravity load like a clevis hanger and never resists dynamic motion

B

It always welds the pipe solid to the steel so no movement of any kind can occur

C

It is identical to a turnbuckle used only for elevation adjustment of cold water lines

D

It permits slow thermal movement but resists rapid dynamic motion such as seismic or shock loads

Test Your Knowledge

A load path for a hung pipe run is sound only when which condition is met?

A

Pipe weight transfers through the attachment hardware into structural steel or foundations designed for the load

B

The hanger rod is bent around obstacles so the pipe can rest on a cable tray

C

U-bolts are tightened until thin-wall pipe is visibly oval, guaranteeing zero movement

D

Supports may be welded to any handrail or thin duct because all plant steel is equivalent

Sections you finish are checked off in the contents.