8.1 Basic Rigging Equipment & Hitches

Key Takeaways

  • NCCER 00106 introduces rigging equipment, common hitches and the Emergency Stop hand signal.

  • Use the actual sling tag and chart for the hitch, angles, conditions and fittings. Check force and rating at every component.

  • Wire rope, webbing, roundslings and alloy chain have different material, inspection and protection limits.

  • The standard construction crane Emergency Stop uses both arms extended to the sides, palms down, sweeping back and forth.

  • Keep bystanders out of the load fall zone. Use the applicable controls for signals, load rotation and landing.

Last updated: November 2026

Basic Rigging Equipment & Hitches

Quick Answer: Pipefitters move valves, spools, pumps, and headers with slings, shackles, hooks, and eye bolts. Module 00106 (NCCER Core basic rigging) expects you to pick the right hitch (vertical, choker, basket), stay under rated capacity, use the required load rotation controls, and recognize the Emergency Stop hand signal. Never stand under a suspended load.

The journey assessment domain Rigging draws from Core 00106 and pipefitting 38102 (8 items of 125 on the Industrial Pipefitter blueprint). This section builds the equipment and hitch foundation every safe lift starts with.

Why pipefitters must own basic rigging

Industrial pipe work constantly requires lifts:

  • Setting a 600-pound gate valve on a rack stub
  • Rolling a fabricated spool into a weld bay
  • Pulling a pump skid a few feet for alignment
  • Staging headers, blinds, and hydrostatic test equipment

Select or attach rigging and give operational signals only within your assigned role and required qualifications. Module 00106 introduces the work. Complete the equipment- and task-specific qualification and training required for the assignment.

Rated capacity and load information

Rated capacity, or working load limit (WLL), applies to a defined configuration. Check the hitch, angles, loading direction, temperature, fittings and sling condition. Compare the actual force on each component with its applicable limit. Check the marked capacity of the complete assembly and the crane capacity at the actual radius and configuration.

Use OSHA §1926.251 for covered construction rigging and §1910.184 for covered general-industry slings. Apply the manufacturer’s identification, instructions and applicable ASME B30 volumes. B30.9 covers slings, B30.26 rigging hardware and B30.10 hooks.

Verify the weight and center of gravity from the approved lift information. For covered construction cranes, §1926.1417(o)(3) provides load verification methods. An equipment weight may exclude attachments, liquid or the gear suspended with the load. Section 4.3 works through those distinctions for a spool. Move smoothly and keep the load clear of obstructions. A sling can overload when a load is jerked or caught even if the static weight is within the rating.

Sling types

Wire rope slings

Wire rope slings are common for general construction and industrial lifts. They offer good abrasion resistance and strength relative to size. Training points:

  • Know lay direction and construction basics (e.g., 6×19, 6×37 class concepts in broader training)
  • Protect contact edges with compatible, rated or otherwise specified edge protection. Confirm the permitted bend diameter.
  • Avoid crushing, kinking, and birdcaging (see Section 8.2 for reject criteria)
  • Do not use wire rope where chemical or high-heat conditions demand other materials unless the sling is rated for that service

Synthetic slings (web and round)

Synthetic web and round slings are lighter, easier on finished surfaces, and flexible around irregular shapes. Critical rules:

  • Read the tag for capacity by hitch type; illegible tags = remove from service
  • Protect against the specified edge and contact geometry, heat, welding spatter and damaging environmental exposure
  • Do not drag under loads or across abrasive surfaces
  • Check fiber, hardware and chemical compatibility. OSHA sets specific environmental limits for covered web slings. For example, nylon is restricted around acids and phenolics, and polyester around caustics.
  • Never tie knots in synthetic slings to shorten them

Chain slings

Alloy chain slings can suit service temperatures outside the range of some synthetic slings. Verify the product’s temperature and contact limits and any required derating. Rules:

  • Use only alloy chain rated for overhead lifting (not proof-coil or hardware-store chain)
  • Know grade markings and master link ratings
  • Avoid sudden shock; chain is strong but not forgiving of overload
  • Inspect links for stretch, gouges, and bent links (Section 8.2)
Sling typeStrengthsWatch-outs
Wire ropeDurable, abrasion-resistant, widely availableSharp bends, birdcaging, broken wires, kinks
Synthetic web/roundLight, load-friendly on painted/machined surfacesHeat, chemicals, cuts, UV, missing tags
Alloy chainHigh strength, better heat tolerance in many casesStretch, nicks, wrong grade, shock loading

Hardware: shackles, hooks, and eye bolts

Shackles

Screw-pin and bolt-type shackles connect slings to loads or master links.

  • Install the correct manufacturer-approved pin fully. Use the specified nut and cotter where the model requires them.
  • Use the approved loading plane and pin arrangement. The Crosby shackle instructions give side-load reductions for specified screw-pin and bolt-type products. Apply the limits for the actual model.
  • Compare shackle force and load direction with the shackle rating and verify the assembled rigging rating

Hooks

Hooks on hoists, come-alongs, and sling assemblies must:

  • Seat the load in the bowl of the hook, not on the tip (point loading)
  • Verify the required latch or closure. A Crosby hook latch retains loose rigging under specified conditions. The hook bowl carries the load.
  • Never be tip-loaded, side-loaded, or back-loaded beyond design
  • Match throat opening and capacity to the attachment

Eye bolts

Eye bolts provide lift points in equipment or fixtures.

  • Use an eye bolt approved for the intended load direction. Crosby permits specified shoulder nut or machinery eye bolts for angular loading and restricts regular nut eye bolts to in-line loads.
  • Follow the instructions for the attachment type, thread engagement, seating and orientation. Check the workpiece and tapped hole or nut arrangement.
  • Angular loading dramatically reduces capacity—use manufacturer angle charts
  • Do not use damaged, stretched, or improvised “eyebolts” cut from scrap rod

Common hitches

How you attach the sling changes capacity and load control.

HitchDescriptionCapacity effect (training concept)Typical pipefitting use
Vertical (straight)One end on the load and one on the hookUse the tagged single-leg vertical rating for the approved connectionLoad with a suitable rated lift point above the center of gravity
ChokerSling passes around the load and through the other eye or designated choke hardwareUse the tagged choke rating and the maker’s choke-angle reduction, if applicableSecure round stock when the hitch and load can remain stable
BasketSling cradles the load and both ends are supportedUse the rated basket capacity for the actual leg angles, load share and contact geometrySupported spool or skid that cannot slip or roll out

Vertical hitch notes

A true vertical hitch loads one leg in pure tension. The load must be stable and the attachment rated. If the center of gravity is offset, the load will tilt—plan attachment points so the hook is above the CG.

Choker hitch notes

Chokers grip the load but:

  • Often have a lower rating than the vertical hitch. Verify the limit and arrange the choke on the sling body as directed for the product.
  • Can compress or damage soft or thin-wall loads. Check load stability, strength and protection.
  • Should not be used where the load can slip out (slick coatings, tapered shapes) unless additional control is provided
  • Double-wrap chokers improve grip on some loads when the method is approved and rated

Basket hitch notes

Basket hitches distribute load but require:

  • Both sides sharing load (avoid one leg taking everything)
  • Attention to sling angle when the basket legs spread (Section 8.3)
  • Protection at contact points so the sling does not cut
  • A load shape that will not roll out of the basket

For example, the Lift-All catalog lists 4,000 lb vertical, 3,200 lb choker and 8,000 lb vertical basket for the Dura-Web 1000 EE2102NF sling in the listed conditions. Those values are specific to the sling and hitch. Section 8.3 applies its choke-angle chart.

Tag lines, signals and fall zones

A tag or restraint line can help control rotation from an assigned position clear of the load and pinch points. For covered construction cranes, §1926.1417(w) requires one when necessary to prevent hazardous rotation. In the power-line provisions of §1926.1408 where tag lines are used, they must be nonconductive. Keep the line clear of routes where it can snag, and keep hands and body clear of loops.

OSHA Subpart CC Appendix A shows Emergency Stop with both arms extended to the sides, palms down, sweeping back and forth. The ordinary Stop signal uses one arm. Under §§1926.1419(h), (j) and 1926.1417(y), one signal person gives operational directions at a time. Anyone who sees a safety problem must give a stop or emergency stop signal, and the operator must obey it. If communication required for the lift is interrupted, safely stop and restore it before resuming.

For a crane covered by §1926.1425, plan the load route to minimize exposure. Keep bystanders out of the fall zone. Only workers needed to receive a load may enter while it lands. The provision separately limits access to a stationary suspended load and specifies controls, including qualified rigging and suitable retention hooks for specified work. Keep clear from directly under the load and between the load and structure. For covered general-industry overhead and gantry cranes, §1910.179(n)(3)(vi) requires the operator to avoid carrying loads over people.

Scenario: setting a valve on a rack

Set a 400 lb flanged valve on a rated support at the rack before making up the joints. Verify the exact valve assembly’s weight and center of gravity, and read the manufacturer’s instructions for the lifting eye. Confirm approval for the complete assembly being lifted. For example, some Fisher actuator lifting points are rated only for the actuator. If the eye permits an in-line pick and the load balances under it, a compatible vertical sling and shackle can work after rating and inspection checks. Use the approved lift route and assigned receiving crew. If the lifting point or sling rating cannot be established, stop and obtain the proper equipment.

Putting Module 00106 together

  1. Identify load weight and center of gravity.
  2. Select sling type for environment and surface protection needs.
  3. Choose hitch: vertical, choker, or basket—and apply the correct capacity for that hitch.
  4. Verify shackles, hooks, and eye bolts are rated, oriented, and latched as required.
  5. Inspect all gear before use; remove defective gear from service.
  6. Use the required rotation controls and signals. Honor Stop and Emergency Stop from anyone.
  7. Never exceed rated capacity and never work under a suspended load.

Master these basics and you are ready for inspection criteria and angle calculations in the next sections—the items that turn “I can hang a sling” into “I can plan a safe pipefitting lift.”

Test Your Knowledge

Which hitch typically reduces a sling’s usable rated capacity compared with a vertical hitch?

A

Basket hitch with both eyes on the hook

B

Vertical (straight) hitch

C

Choker hitch

D

Two independent vertical hitches on separate padeyes each at full capacity without considering the system

Test Your Knowledge

During a covered construction crane lift, who may and must give a stop or emergency stop signal when they become aware of a safety problem?

A

Only the crane manufacturer’s representative

B

Only the designated signal person for that lift

C

Only the site superintendent after a written stop-work order

D

Anyone who sees a dangerous condition developing

Test Your Knowledge

A pipefitter needs a sling for a painted finished spool where abrasion is moderate and surface protection matters. Which statement best matches basic equipment selection?

A

Synthetic web or round slings are often preferred for finished surfaces when heat and chemical limits allow

B

Proof-coil hardware-store chain is preferred because it is inexpensive

C

Any wire rope with broken strands is acceptable if the load is under one ton

D

Knotting a synthetic sling is the approved way to shorten it for a choker

Test Your Knowledge

How should you use the sling, shackle and eye-bolt ratings for a single in-line vertical hitch?

A

Average the three printed ratings

B

Check each component and the assembled hitch in the actual configuration. Use the lowest applicable working load limit.

C

Use the highest rating to cover the other components

D

Ignore a lower hardware rating if the crane can lift the weight

Sections you finish are checked off in the contents.