4.1 Oxyfuel Equipment & Setup
Key Takeaways
Trace each marked gas path from a compatible regulator and hose through the torch to the correct tip.
A check valve limits reverse gas flow. A flashback arrestor limits upstream flame travel. Verify the actual model configuration.
Acetylene at the torch has a 15 psig ceiling. Set the working pressure from the manufacturer’s chart for the fuel, tip and task.
Federal storage rules distinguish construction from general industry. Secure cylinders and follow the applicable rules for movement, in-use status and separation.
Use the model’s leak-check, separate purge, lighting and shutdown sequence. Select eye, clothing, fume and hot-work protection for the operation.
Oxyfuel Equipment & Setup
Quick Answer: A fuel–oxygen flame preheats the steel. A separate oxygen jet oxidizes the metal and clears the cut. Trace both gas paths, verify the hose and connection markings, inspect protective devices, then follow the manufacturer’s setup, lighting and shutdown procedure for the actual torch and fuel.
The Industrial Pipefitter assessment (PFT08_03) allocates 10 items (8%) to the Cutting domain, drawn from oxyfuel module 29102 and field-routing module 08307. This section builds equipment and setup fluency so later technique and field-routing items rest on safe habits, not guesswork.
How oxyfuel cutting works
- A preheat flame (fuel gas + oxygen) brings the steel to its kindling temperature for oxygen cutting.
- A pure cutting-oxygen stream from the tip’s center orifice oxidizes the metal and blows molten oxide (slag) out of the kerf.
- The torch is advanced so preheat and oxygen jet stay in the cut.
The fuel flame supplies preheat. After ignition, the oxygen jet sustains the reaction at the cut face. Jet quality depends on oxygen purity, tip condition and delivery pressure.
System components
| Component | Function | Exam-critical notes |
|---|---|---|
| Oxygen supply | Supplies oxygen for preheat and for the cutting jet | Identify the gas from the cylinder marking. Check the regulator’s inlet rating and connection. |
| Fuel-gas supply | Provides fuel for the preheat flame | Use the torch, tip, hose and regulator intended for the actual fuel. Acetylene and propane have different equipment and setup requirements. |
| Regulators | Reduce supply pressure to the required delivery pressure | Match the regulator to the gas and approved inlet connection. Unload the adjustment before opening the cylinder as directed. |
| Hoses | Keep the gases separate on the way to the torch | In the Victor oxyacetylene example, green carries oxygen and red carries acetylene. Trace the hoses and check the markings and connections. |
| Torch handle and cutting attachment | Control fuel, preheat oxygen and cutting oxygen | On the Victor attachment, the preheat control is separate from the cutting oxygen lever. |
| Cutting tips | Direct the preheat flames and center cutting jet | Choose the listed tip for the fuel, attachment and cut. Clear blocked orifices with the correct tip cleaner. |
| Check valves and arrestors | Address reverse gas flow and upstream flame travel respectively | Use the integral or accessory protection and placement specified for the model. |
The Victor handle uses a right-hand oxygen hose fitting and a left-hand fuel fitting. Federal construction rule §1926.350(f)(1) requires distinguishable, noninterchangeable hoses. Color and touch are recognized ways to distinguish them. Never force a mismatched connection.
Acetylene delivery pressure. Do not use acetylene at the torch above 15 psig. The Victor manual treats that as a ceiling and the tip chart gives the actual working range. Federal general industry §1910.253(a)(2) also specifies a 30 psia absolute ceiling, relevant in pressurized environments. Those limits do not describe the pressure inside a supplier’s approved dissolved-acetylene cylinder. Construction §1926.350(d)(3) requires a suitable regulator for the cylinder-fed torch.
Reverse-flow check valves, flashback arrestors and abnormal flame
A reverse-flow check valve limits gas flowing back into the opposite supply line. A flashback arrestor helps stop a flame front from progressing upstream of its location. A combined device can provide both functions. For example, Victor FC handles have both built in. Victor cautions against adding accessory arrestors to those handles because they can restrict flow. For other models, verify the required approved protection and follow the inspection and service instructions.
- Backfire: A momentary pop when the flame retreats into the torch and goes out or returns to the tip.
- Sustained backfire: Combustion continues inside the torch and can produce a continuous hiss or whistle. The Victor cutting-attachment procedure calls for immediate closure of the preheat oxygen valve followed by the torch fuel valve.
- Flashback: Flame travels back through the torch toward or into the hose and gas supply. Stop work, follow the equipment emergency procedure, and keep affected equipment out of use pending competent inspection. If a fire cannot be safely controlled, evacuate and raise the alarm. In construction, §1926.350(f)(4) requires testing flashback-exposed or severely worn or damaged hose at twice its normal service pressure, with a 300 psi minimum. This is a hose test requirement. Defective or doubtful hose is out of service.
Cylinder storage, movement and handling
| Control | Application |
|---|---|
| Secure cylinders | Use a rated cart or fixed restraint. Use and store acetylene with the valve end up. Its porous filling holds a solvent in which acetylene is dissolved. Consult the supplier before using a cylinder found on its side. |
| Protect the valve | In construction, close the cylinder valves before moving. Remove regulators and fit the caps unless the cylinders are firmly secured on a special carrier intended for that move. A cap is never a lifting point. |
| Separate oxygen in storage | Under construction §1926.350(a)(10) and general industry §1910.253(b)(4)(iii), separate stored oxygen from fuel-gas cylinders or combustible materials by at least 20 ft or a noncombustible barrier at least 5 ft high with at least a ½-hour fire-resistance rating. |
| Keep oxygen fittings clean | Keep oil and grease off oxygen cylinder valves, fittings, regulators, hands and gloves. Follow the supplier’s instructions if contamination is found. |
| Control placement | Keep cylinders clear of heat, slag and damage. Keep cylinders outside confined spaces during construction under §1926.350(b)(4). |
OSHA’s May 10, 2006 interpretation distinguishes an in-use oxyacetylene set from storage. In construction, gas must be drawn or reasonably expected to be drawn within 24 hours for the set to count as in use. For the general-industry storage rule, a working single pair in use or connected for use is treated as out of storage. Simply leaving a regulator attached does not meet the construction test. Secure cylinders even when they are in use.
Setup, checks and lighting for a Victor oxyacetylene cutting attachment
Use the actual model manual. This example follows Victor’s Cutting, Heating and Welding Guide, sections 4 and 7, and its oxyacetylene training checklist. Different fuel or torch configurations have their own instructions.
- Inspect the secured cylinders, matching regulators, hoses, protective devices, tip seats and the attachment’s required O-rings. Clear the work area and keep ignition sources away from gas connections. Put defective parts out of service.
- For the cylinder connections covered by OSHA, briefly open and immediately close the valve before attaching its regulator. Stand to the side and keep fuel gas away from all ignition sources. Attach the correct regulators and hoses, using clean oxygen-service connections. Do not improvise a seal or use an adapter to defeat the gas-specific connection.
- Back out regulator adjustments and close the torch controls before pressurizing. Open the cylinder valves slowly from the side. Fully open the Victor example’s oxygen cylinder valve as instructed. In general industry OSHA limits acetylene valve opening to 1½ turns, preferably ¾ turn or less. In construction §1926.350(d)(2) limits the fuel-gas cylinder valve to 1½ turns and requires leaving a special wrench on the stem when one is needed during use (with separate provision for manifolded cylinders). Use the applicable valve and torch procedure.
- Leak-test the assembled equipment before lighting. Follow the model’s gauge checks and use an approved leak-detection solution where specified, never a flame. Shut down and correct any leak before proceeding. Purge each path separately through the torch in a ventilated area, away from ignition sources. Set the delivery pressures as directed while the appropriate gas is flowing. Use the chart for the actual fuel, tip, thickness and hose configuration.
- On this Victor attachment, fully open the torch-handle oxygen supply valve as directed and keep the attachment’s preheat oxygen control closed for ignition. With the tip pointed safely away from people, open the torch fuel valve slightly and ignite with a friction sparklighter or approved device. Open the preheat oxygen control and adjust the flame. Depress the cutting lever and verify that the preheat remains neutral with cutting oxygen flowing.
Flame types
| Flame | Gas balance | Visual cue (training description) | Typical use |
|---|---|---|---|
| Carburizing (reducing) | Excess fuel | Acetylene “feather” beyond the inner cone | Use when specified, for example in some hardfacing operations |
| Neutral | Neither reducing nor oxidizing | Defined inner cone and no acetylene feather | Victor’s specified preheat for this carbon-steel cutting example |
| Oxidizing | Excess oxygen | Shorter, sharper inner cone | Use only if specified for the operation |
For the specified neutral oxyacetylene setting, bring the feather back to the inner cone, then check the flame with the cutting lever depressed. Read alternate-fuel flames using the corresponding tip instructions.
Shutdown for the Victor cutting attachment
- Release the cutting oxygen lever. To extinguish the flame on this attachment, close the preheat oxygen valve, then the torch fuel valve.
- Close both cylinder valves. In a safe location, bleed oxygen through the specified torch controls, including the cutting lever, then close those controls. Relieve the oxygen regulator’s adjusting spring as directed.
- Bleed the fuel side separately, close the torch fuel valve, and unload the fuel regulator. Verify both sides are depressurized before disturbing any connection. One gas path stays closed while the other is purged or bled.
- Secure the torch and hoses and move the cylinders only with the protections for the intended move.
Some Victor training checklists show the fuel side bled first after both cylinders are closed. The model instructions govern the sequence. Separate extinguishing the flame from isolating and bleeding the supply. Never leave a lit torch unattended.
PPE and work-area controls
- Eyes and face: Use filter lenses rated for oxygen cutting and the metal thickness, with suitable protection from flying slag. See §1926.102 or §1910.133 for the applicable federal setting.
- Body, hands and feet: Wear flame-resistant clothing, appropriate dry gloves and protective boots. Keep exposed skin out of the slag path.
- Fumes: Identify the base material and its coating before heating. Use the required ventilation and respiratory controls under construction §1926.353 or general-industry §1910.252(c).
- Fire: Follow the applicable hot-work authorization and fire-watch requirements. Clear or shield nearby combustibles, including openings through which slag can travel. See Section 1.4 for site and federal hot-work controls.
Scenario: first cut of the shift
An inherited Victor cart has unverified hose routing and a slag-blocked tip. Identify each cylinder from its label and trace its hose. Check the installed protective devices and clean the cooled tip with the correct tip cleaner or replace a damaged tip. Check for leaks before lighting. Purge each gas path separately, set the chart’s working pressures and recheck the neutral preheat with cutting oxygen flowing. If the jet is uneven or a leak persists, take the outfit out of service.
Putting Module 29102 equipment together
- Trace each gas from its marked source through its own regulator, hose and torch controls.
- Apply the appropriate storage and handling rules. Keep the oxygen system clean.
- Verify the specified check-valve and arrestor configuration. Stop and investigate abnormal flame behavior.
- Leak-check, purge separately and set the chart’s delivery pressures before lighting. Observe the acetylene ceiling.
- Follow the model-specific sequence for extinguishing, isolating and bleeding the equipment.
On the Victor oxyacetylene outfit described in this section, which hose assignment is correct?
Oxygen hose red; fuel-gas hose green
Oxygen hose green; fuel-gas hose red
Both hoses black with painted bands only
Oxygen hose blue; fuel-gas hose yellow
What is the primary functional difference between a reverse-flow check valve and a flashback arrestor on an oxyfuel system?
Both devices only regulate cylinder pressure to working pressure
Check valves meter tip orifice size; arrestors color-code hoses
They are identical devices with two marketing names
Check valves resist reverse gas flow; flashback arrestors help stop a flame front from traveling back into the hose/regulator system
Victor’s procedure calls for what preheat flame during the carbon-steel cut described in this section?
Neutral flame
Heavy carburizing flame with a long feather
Strongly oxidizing flame with maximum excess oxygen
Fuel-only flame with the oxygen cylinder closed
The flame on the Victor cutting attachment is out and both cylinder valves are closed. How should you relieve the gas left in the hoses?
Remove both pressurized regulators immediately
Relight the torch to burn out both hoses
Bleed one gas path through the prescribed torch controls, close it, then bleed the other path separately and complete the regulator shutdown
Open both torch valves together so the gases can escape faster
Sections you finish are checked off in the contents.