2.1 Fractions, Ratios & Algebra
Key Takeaways
Pipe measurements may be given in mixed fractions or decimals. Convert them to the same form and unit before adding or subtracting lengths. For example, 1/16 in = 0.0625 in.
Use corresponding terms in the same order when setting up a proportion for drawing scale, a mixture, or similar triangles.
Basic algebra rearranges trade formulas (cut length, pressure/area concepts, flow relationships) so you isolate the unknown before substituting numbers.
Always convert units first (inches ↔ feet, feet ↔ decimal feet) and keep center-to-center, end-to-end, and face-to-face labels distinct.
NCCER allocates 15 items to the Math domain, which draws from Pipefitting Trade Math (08204) and Advanced Trade Math (08304).
Why trade math matters on the pipefitter assessment
Math is its own domain on the NCCER Industrial Pipefitter journey assessment (PFT08_03): 15 items (12%), drawn from Level 2 Pipefitting Trade Math (08204) and Level 3 Advanced Trade Math (08304). NCCER allows a non-programmable, non-printing calculator and The Pipefitters Blue Book by W.V. Graves. Label the units and reference points before using either.
This section builds the Level 2 foundation: fractions, ratios/proportions, simple algebra, and unit conversions. Later sections add geometry, offset constants, and odd-angle trigonometry. Almost every fabrication length, hydro-fill estimate, and isometric take-off starts with clean arithmetic on mixed units.
Fractions for measurements
Field dimensions are often expressed as mixed numbers (for example, 12 ft 7-3/8 in or a cut of 46-5/16 in). Exam problems often force you to add, subtract, multiply, or divide those values and then report an answer in a specific form.
Adding and subtracting. Convert all lengths to the same unit and the same denominator, then combine numerators.
Worked example — add cut pieces for a straight run:
- Pieces: 3-1/4 in + 5-7/8 in + 2-1/2 in
- Common denominator 8: 3-2/8 + 5-7/8 + 2-4/8 = (3+5+2) + (2+7+4)/8 = 10 + 13/8
- 13/8 = 1-5/8, so total = 11-5/8 in
Worked example — subtract takeout from center-to-center:
- Center-to-center (C-C) = 48 in; combined fitting-center to finished-pipe-end takeouts = 9-3/4 in
- Cut length concept: C-C − takeouts = 48 − 9-3/4 = 38-1/4 in
Keep the labels straight: center-to-center, end-to-end, and face-to-face are different. Wrong label + correct arithmetic still fails the item.
Multiplying and dividing. Multiplying a length by a whole number scales a repeated part (for example, four equal legs). Dividing finds equal spacing or unit rates.
Worked example — equal hanger spacing:
- Span between anchors = 36 ft 0 in; three equal spaces → 36 ÷ 3 = 12 ft center spacing (verify end hangers are not double-counted per the drawing notes).
Decimal equivalents of common fractions (memorize at least sixteenths—Blue Book tables help, but exam time is limited):
| Fraction | Decimal (in) | Fraction | Decimal (in) |
|---|---|---|---|
| 1/16 | 0.0625 | 9/16 | 0.5625 |
| 1/8 | 0.1250 | 5/8 | 0.6250 |
| 3/16 | 0.1875 | 11/16 | 0.6875 |
| 1/4 | 0.2500 | 3/4 | 0.7500 |
| 5/16 | 0.3125 | 13/16 | 0.8125 |
| 3/8 | 0.3750 | 7/8 | 0.8750 |
| 7/16 | 0.4375 | 15/16 | 0.9375 |
| 1/2 | 0.5000 | 1 | 1.0000 |
Worked example — convert and compare:
- A drawing shows 0.4375 in clearance. That is 7/16 in. If the available gap is 3/8 in (0.375), the fit is short by 0.0625 in = 1/16 in.
Ratios and proportions
A ratio compares two quantities (a 3:1 mix or a 1:48 drawing scale). A proportion sets two ratios equal so you can solve for an unknown part.
If b and d are nonzero, a/b = c/d implies a × d = b × c.
Scale drawings. If a plan is drawn 1/4 in = 1 ft (which is 1:48), then a measured inch represents 4 ft on the correctly sized print. For fabrication use the stated dimensions and revision. Scale a drawing only when the drawing or exercise directs you to do so.
Worked example — scale length:
- Scale: 1/8 in = 1 ft (1:96). Measured line on print = 3-3/8 in.
- Real length = 3.375 × 8 = 27 ft (because each 1/8 in map = 1 ft → multiply map inches by 8).
Worked example — unknown scale dimension:
- With a unitless scale of 1:20, a 40-ft run is represented by 40 ft ÷ 20 = 2 ft, or 24 in, on the sheet. A stated scale of 1 in = 20 ft uses different units and would give 2 in on the sheet for the same run.
Mix and solution ratios appear less often than piping geometry but show up in advanced trade math and shop problems (for example, antifreeze mix, cleaning solutions, or two-part compounds used near piping work).
Worked example — proportion mix:
- An exercise calls for a 1:4 concentrate-to-water ratio by volume and assumes the two volumes add directly. The finished volume is 15 gallons. Concentrate = 15 × (1/5) = 3 gal; water = 12 gal.
Similar triangles / proportional offsets foreshadow offset math: if a 45° triangle has equal legs, any scaled copy keeps equal legs. If run:offset = 1:1 on a small mock-up, the full-size run equals the full-size offset.
Basic algebra for trade formulas
You rarely invent formulas on the exam—you rearrange known relationships so the unknown stands alone.
Rules of thumb:
- Write the formula.
- Isolate the unknown using inverse operations (add/subtract, multiply/divide).
- Substitute values with consistent units.
- Check that the answer’s unit and magnitude make sense.
Conceptual pressure relationship (not a substitute for code design, but useful for literacy):
- For uniform pressure difference P across a flat surface, the net normal force is F = P × A. If pressure doubles at constant area, force doubles. If area doubles at constant pressure, force doubles. Exam items may ask which variable moves which way rather than deep fluid dynamics.
Worked example — isolate area:
- A uniform 100 psi pressure difference produces a net force of 12,560 pounds-force on a flat circular surface. A = F/P = 12,560/100 = 125.6 in², the area of a circle about 12.65 in in diameter.
Flow literacy (conceptual). The volume rate is the internal area times the mean flow velocity. At the same volume rate, halving the inside diameter quarters the area and quadruples the mean velocity.
Cut-length style rearrangement:
- If T1 and T2 are measured from fitting centers to the intended pipe ends, C-C = L_cut + T1 + T2, so L_cut = C-C − T1 − T2.
- If travel = offset × constant, then offset = travel / constant.
Worked example — rearrange travel formula:
- Travel measured = 28.28 in on a 45° offset. Constant = 1.414. Offset = 28.28 / 1.414 ≈ 20.0 in.
Unit conversions: inches, feet, and decimal feet
Pipefitters live in mixed systems: architects may dimension in feet-inches; isometrics may use decimal inches; elevation math often uses decimal feet.
| Conversion | Operation |
|---|---|
| Inches → feet | ÷ 12 |
| Feet → inches | × 12 |
| Inches → decimal feet | ÷ 12 |
| Fractional inch → decimal inch | use table above |
| Feet-inches → total inches | ft×12 + in |
Worked example — feet-inches to total inches:
- 7 ft 4-1/2 in = 7×12 + 4.5 = 84 + 4.5 = 88.5 in.
Worked example — total inches to feet-inches:
- 155 in ÷ 12 = 12 ft remainder 11 in → 12 ft 11 in.
Worked example — elevation difference in decimal feet:
- High point 112.50 ft; low point 109.75 ft; difference = 2.75 ft = 2 ft + 0.75×12 = 2 ft 9 in.
Trap: mixing decimal feet with inches without converting (for example, treating “2.5” as 2 ft 5 in instead of 2 ft 6 in). Always decide: is the number feet or inches?
Exam habits that save points
- Convert everything to one unit before arithmetic.
- Write intermediate values with their units to catch inverted fractions.
- Match the answer form requested (nearest 1/16 in, nearest 0.01 in, feet-inches).
- When a proportion feels backward, cross-multiply on paper rather than “eyeballing.”
- Keep calculator mode in degrees for later trig sections (set it now as a habit).
Master these foundations and the geometry/offset sections become applications rather than new languages. Module 08204 expects fluency here before 08304 adds sine, cosine, tangent, interpolation, and rolling offsets.
Sources checked November 15, 2026. NCCER Pipefitting curriculum, OpenStax proportions, and NIST units of measurement.
A pipefitter must add three cut lengths: 4-3/8 in, 6-1/2 in, and 2-3/4 in. What is the total length?
12-5/8 in
13-5/8 in
13-3/8 in
14-1/8 in
A scale exercise uses a correctly sized drawing at 1/4 in = 1 ft. A spool run measures 2-1/2 in on the print. What length does it represent?
5 ft
8 ft
10 ft
12 ft
If travel = offset × 1.414 and the travel of a 45° offset is 21.21 in, what is the offset (nearest 0.01 in)?
15.00 in
10.61 in
21.21 in
30.00 in
Convert 9 ft 7-1/4 in to total inches.
109.25 in
115.25 in
117.25 in
127.25 in
Sections you finish are checked off in the contents.