9.4 Flanges, Gaskets & Bolt-Up

Key Takeaways

  • Select the flange type and facing called for by the piping specification, then verify mating geometry and dimensions.

  • Find allowable pressure at the design temperature using the component standard, class and material. Verify the complete joint against its governing requirements.

  • Use the specified new gasket for the face, size and service. Raised, flat and ring-type joint faces take different seals as specified.

  • Clean and align surfaces before tightening. Achieve the specified gasket load with the approved torque or tensioning sequence.

  • An operating line blank and a temporary test closure serve different purposes. Verify rating and reinstatement under the test plan.

Last updated: November 2026

Flanges, Gaskets & Bolt-Up

Quick Answer: Verify flange type, class and material, facing, gasket and bolting as a system. Align and inspect the mating faces and use the approved tightening or tensioning procedure. Install the specified new gasket when reassembling a joint fitted with a spiral-wound or RTJ gasket.

A flange joint relies on bolt preload to compress a compatible gasket between suitable seating surfaces. Errors in any of these parts can lead to leaks even when the flange itself has the correct class marking.

Flange types

TypeHow it attachesTypical use / notes
Weld neck (WN)Butt weld to pipe; long tapered hubTapered hub and groove weld transfer load to the pipe. Use when the design requires that connection.
Slip-on (SO)Fits over the pipe. Follow the designed weld detail.B31.3-2024 §308.2.1 identifies services requiring welds on both sides and restricts use under severe cyclic conditions.
Socket weld (SW)Pipe into socket; fillet weldUsed in specified small-bore service. B31.3-2024 Fig. 328.5.2-2(c) shows an approximately 1/16 in. clearance before welding.
BlindSolid flangeCloses a rated flange end or unused nozzle when the design specifies it.
Lap joint (LJ)Loose ring flange over stub endEasy bolt-hole alignment; frequent dismantling; stub end is the wetted piece
ThreadedScrewed to pipeLimited services; not preferred where vibration or high cyclic load dominates
Orifice / specialMetering or specialty facesFollow instrument/spec details

Wafer valves sit between flanges. Check alignment, through-bolt arrangement, body centering, disc clearance and whether the manufacturer specifies separate gaskets.

ASME class and service rating

ASME B16.5 covers specified flanges through NPS 24. ASME B16.47 covers large-diameter steel flanges from NPS 26 through 60. Verify the applicable standard and its edition, nominal size, class, material group and facing before checking the actual rating. A class number is a designation. The table gives the pressure at the stated temperature. The design must also permit the pair of mating flanges, fasteners and gasket. When the design permits compatible flanges of unequal ratings, B31.3-2024 §312.1 limits the joint to the lower-rated flange and limits torque so the lower-rated flange is protected.

Worked lookup. For an ASTM A105 steel flange in B16.5-2025 Table 2-1.1C, Class 150 allows 285 psig at 100°F and 170 psig at 500°F. A specified 180-psig design at 500°F exceeds that flange’s table rating by 10 psi. Reject the proposed flange for that design point and refer selection to the piping specification and responsible designer. A larger class number alone cannot verify mating fit or allowable service.

Flange faces: raised face vs RTJ

Face typeSealing methodCommon gaskets
Raised face (RF)Gasket compressed on raised annular faceSpecified sheet or spiral wound compatible with the seating finish and service
Flat face (FF)A flat seating surface. A full-face gasket can distribute load over the wider area.Often full-face sheet. Follow the approved design for brittle or dissimilar flanges.
Ring-type joint (RTJ)Metal ring in precision groovesOctagonal or oval ring joint gaskets

The flange and gasket geometries must match. Use the specified compatible facing and gasket. In an RTJ assembly the groove and compatible metal ring provide the seal.

Gasket types

GasketConstructionTypical service notes
Sheet (compressed fiber, PTFE, graphite sheet, etc.)Cut rings or full face from sheetVerify pressure, temperature, compatibility and seating stress for the specified product.
Spiral woundMetal winding and filler. Inner and outer rings depend on the applicable standard, design and service.Common for specified process flanges. Verify the ordered construction and seating loads.
Ring joint (RTJ)Solid metal ring (soft iron, stainless, etc.)RTJ groove seals. Verify ring designation, material and hardness and fit a new specified ring.
Jacketed / kammprofile / specialtyEngineered compositesHeat exchangers, special services per spec

Specify the gasket by facing, size, class where applicable, material and service. ASME B16.20 covers ring-joint, spiral-wound and jacketed metallic gaskets. B16.21 covers nonmetallic flat gaskets. Check that the gasket sits on the intended surface without projecting into the bore. B31.3 §335.2.4 permits no more than one gasket between a pair of contact faces. A used spiral-wound or RTJ gasket can look intact yet lack the recovery or deformation needed to seal again.

Bolt materials and lubrication

  • Use specified studs/bolts and nuts (e.g., ASTM grades for temperature service)—not random hardware-store bolts
  • Apply approved lubricant/anti-seize to threads and nut bearing faces when the torque procedure assumes it; dry torque values differ from lubricated values
  • Inspect studs and nuts for loss of section, corrosion or thread damage. Use accepted fasteners with complete engagement through the nut as required by B31.3 §335.2.3.
  • Hardened washers when specified

Pass sequence and gasket load

For B31.3 work, §335.2 calls for uniform gasket compression to its design load. ASME PCC-1 provides guidance for bolted pressure-boundary joints with a ring-type gasket wholly inside the bolt circle and no contact outside that circle. Apply the approved procedure for the joint and product, particularly for full-face gaskets, lined joints, brittle flanges or RTJ joints.

Example. An approved procedure for an eight-bolt raised-face flange uses a cross sequence. With bolt positions numbered consecutively around the circle, a cross sequence can be 1, 5, 3, 7, 2, 6, 4, 8. For a joint whose procedure adopts the PCC-1-2022 legacy pattern with steps of 30%, 60% and 100%, a specified target of 200 lb-ft gives passes of 60, 120 and 200 lb-ft. The procedure finishes with a circular check at the target until the nuts stop rotating at that setting. These are fractions of a specified target. Get the actual preload method, values and passes from the approved instructions.

MistakeResult
Tighten one side fully firstGasket extrusion, flange gap cocking, chronic leak
Single-pass full torqueUneven load, crushed gasket soft spots
Wrong torque (no lube vs lubed table)Under/over-stress; yield bolts or weep
Missing bolts or short stud engagementJoint failure under pressure

Hydraulic tensioning or calibrated torque wrenches are used on large or critical flanges per procedure. Use the specified tool, load method and acceptance criteria.

Alignment and gap before gasketing

Before inserting the gasket:

  • Verify the flange face alignment and separation against the engineering design and applicable code. B31.3-2024 §335.1(c) gives alignment routes and a bolt-hole offset limit unless the design specifies otherwise.
  • Clean the seats and check surface finish and damage. Repair or replace a flange whose surface cannot seat the gasket.
  • Correct support or fit-up where needed. Use only the specified method for designed cold spring or approved rework. B31.3 §335.1 prohibits introducing detrimental strain.

Exam Tip: If a joint leaks after startup, common root causes are wrong/reused gasket, uneven bolt-up, misalignment, or wrong face/gasket combination—not “needs more pipe dope on the spiral wound.”

Blind flanges and test blinds

Blind flanges close an end or nozzle when rated and specified for the duty. Operating line blanks to ASME B16.48 and temporary closures for a pressure test serve different purposes. Select and verify test closures, fasteners and the safe pressure differential using the approved test plan. Under B31.3-2024 §345.3.4, a valve may isolate excluded equipment during a test only if the valve and its closure mechanism are suitable for the test pressure. Restore relief paths and inspect the reinstated gasketed joints. In B31.3-2024, §345.2.3(b) covers specified reassembled mechanical joints, including joints used to install temporary test isolation. The approved plan identifies any required inspection or testing of the reinstated joint.

Scenario: RF spiral wound vs RTJ mix-up

A Class 600 RTJ valve is delivered with a spiral-wound gasket bag from a Class 150 RF job. The flange needs the specified ring-joint seal. Verify both mating groove designations, inspect the seating surfaces and obtain a new ring of the specified size, profile, material and hardness. Use the approved RTJ procedure and check joint acceptance before pressurizing.

Putting flanges and bolt-up together

  1. Select flange type for fabrication and service severity (WN for critical butt-weld lines, etc.).
  2. Match ASME class, material, and face type to the spec.
  3. Choose sheet, spiral wound, or RTJ ring that belongs on that face—and use a new undamaged gasket.
  4. Align faces; lubricate fasteners as specified.
  5. Apply the approved bolt-load method, passes and check sequence.
  6. Perform the specified leak examination under the approved test procedure. Stop and depressurize before correcting a leaking test joint.
Test Your Knowledge

Which flange type uses a tapered hub butt-welded to the pipe and is preferred for many high-pressure or cyclic services?

A

Weld neck flange

B

Slip-on flange with only a single tack weld

C

Lap joint flange without a stub end

D

Blind flange used as a pipe reducer

Test Your Knowledge

What gasket style is used with ring-type joint (RTJ) flanges?

A

Full-face compressed sheet cut for Class 150 flat face only

B

Soft rubber garden-hose washer

C

Metal ring joint gasket (octagonal or oval) seated in the flange grooves

D

Spiral-wound gasket crushed into the RTJ groove as a permanent substitute

Test Your Knowledge

What does the cross pattern accomplish in an approved staged flange tightening procedure?

A

It completes one entire half of the flange before the other

B

It determines which bolt grade to use

C

It removes the need for alignment checks

D

It helps distribute gasket load as bolt preload increases in stages

Test Your Knowledge

After a successful hydro test, the pipe is depressurized and an RF joint is opened to remove a temporary test blank. What should the crew do with the used spiral-wound gasket?

A

Reuse it if its outer ring looks undamaged

B

Discard it and install a specified new gasket for the operating joint

C

Reuse it by placing a new sheet gasket on top

D

Reuse it by raising the final torque above the approved value

Sections you finish are checked off in the contents.