7.2 Haircutting Tools (Shears, Razors, Clippers, Texturizers) & Proper Handling

Key Takeaways

  • Check the condition of the cutting edge, the pivot and the fit of the shears before use. Close the blades while switching to the comb.

  • Observe the hair’s natural fall and reduce tension where pulling would distort the finished length.

  • Choose a texturizer or clipper attachment by the exact tool and the amount of hair to remove.

  • Use the blade and moisture conditions specified for the haircutting razor and technique. Set used blades aside in the appropriate sharps container.

Last updated: November 2026

7.2 Haircutting Tools (Shears, Razors, Clippers, Texturizers) & Proper Handling

Shears and Texturizers

Use straight haircutting shears to establish a cutting line. Toothed shears can reduce bulk or soften a transition by cutting selected fibers that enter the teeth. The tool’s edge, tooth design, condition and fit affect how it works. A steel hardness rating measures indentation under specified test conditions. It cannot by itself predict the fit, edge life or cutting behavior of a particular pair of shears. NIST Rockwell hardness test and manufacturer shear specifications

Shear partWhat to check
Thumb ring and finger ringFit the thumb and ring finger comfortably. Use a left- or right-handed model suited to your grip.
Finger rest or tangSupport the little finger if the model has a rest. Some handles have a detachable rest.
Pivot and tension adjusterCheck that the blades open and close smoothly without guessing at a universal setting. Follow the care instructions for the model.
Thumb-side and finger-side bladesUse the thumb to open and close while the fingers stabilize the other side. Put away damaged tools until repaired or replaced.

When palming the shears to switch to the comb, close the blades, slip the thumb out of its ring and hold the shears securely against the palm with the points clear of the client and your fingers. Once the hair is sectioned and controlled, return the thumb to its operating position to cut. If you cannot control both tools, put the closed shears on a clean, secure surface while you comb. Adjust the chair and move around the client to keep the work within comfortable reach and reduce sustained shoulder or wrist strain. Jatai shear handling demonstration, Kasho care instructions and NIOSH ergonomic factors

Worked selection. A dense section needs a small reduction in bulk while the perimeter stays visible. Start with limited removal inside the section and release it before repeating a pass. The BMAC Tokyo thinning shear, for example, has 29 teeth and a maker’s stated 30% cut. That description belongs to the model. Tooth count alone does not set how much hair another tool will remove, and repeated passes can remove more than intended. Jatai BMAC texturizer specifications

Razor Use and Blade Handling

A haircutting razor and its blade can create a softer edge in a suitable section. Check the tool’s intended use and the hair’s condition first. Moisture depends on the tool and technique. For example, Feather’s instructions for its Hair Cut Monster tool specify slightly damp hair for sections other than the fringe, which stays dry. A Jatai professional demonstration uses a Feather texturizing razor to finish on dry hair. Stop if the blade snags or pulls, then reevaluate the hair, the blade condition and the tool choice. Feather’s instructions and Jatai’s Feather dry-finishing demonstration

Use a compatible blade and leave the tool’s guard in place when specified by its design. For example, the Feather Styling Razor uses guarded replaceable blades and a blade-change system designed to avoid touching the edge. Set used single-use blades in the designated sharps container. Georgia Rule 240-4-.03(7) specifies upright storage, the biohazard label and the manufacturer’s safety flap, and disposal at three-quarters full. Follow local disposal rules. Remove hair and reprocess the holder according to the applicable rule and the manufacturer’s instructions before reuse. Feather Styling Razor and blade system and Georgia Chapter 240-4

Clippers and Trimmers

A clipper uses a moving cutter against a stationary blade. Use it for shorter lengths, tapered transitions or clipper-over-comb work. In clipper-over-comb, lift a small section with the comb at the desired angle and remove the hair projecting beyond the comb. A trimmer helps detail a hairline or sideburns. Use compatible attachments. In Wahl’s color-coded guide set, the #2 is marked 1/4 inch and the #3 is marked 3/8 inch. Read the markings for the actual set. A taper lever and how the comb is held can affect the result. Wahl Magic Clip and Wahl color-coded guides

Before starting, check for a damaged cord, blades or attachment and make sure the comb is secure. Between clients, switch off the device before removing parts for cleaning. Follow the manufacturer for the electrical body and the applicable Georgia process for reusable client-contact parts, including removable parts suited to wet disinfection. Keep liquids away from electrical components. Store processed implements as Georgia requires, apart from items waiting to be cleaned and disinfected. OSHA portable equipment rules, Wahl clipper instructions and Georgia Rules 240-4-.04 and .05

Control Tension and Prepare for the Practical

Use consistent control within a section. When a curl, cowlick or the curve over an ear changes the way hair settles, ease the tension and check the length after release. To cut at natural fall, observe the texture as the client actually wears it. Leave enough length to reassess the shape after drying. Check a dense area in smaller partings so the guide stays visible. Pivot Point sculpture skills, pp. 34–43

Georgia’s PSI practical gives the haircutting task 20 minutes, with five minutes each for preparation, shears, razor and cleanup. The test assesses both tools, safe work and cutting at least one inch throughout the haircut. Work for the time and with the tools PSI directs. Confirm the salon client’s requested length separately. PSI Georgia bulletin, topic 6

Test Your Knowledge

The blade of a haircutting shear catches while the stylist is practicing. What should the stylist check before using it on a client?

A

The hardness rating alone, since it determines whether the shear opens smoothly.

B

The shaping line only, continuing to use the shear if it looks sharp.

C

The pressure on the client’s hair, then compensate by holding the subsection tighter.

D

The condition of the blades, the pivot and model-specific tension adjustment.

Test Your Knowledge

While combing a subsection near the client’s ear, how can the stylist control the shears?

A

Keep the shears open and move the comb between the blades.

B

Close and palm the shears, with the thumb out of the ring and the tips clear of the ear.

C

Close the blades only as the comb passes the ear.

D

Keep the tips pointing toward the ear so the shears are ready to cut.

Test Your Knowledge

You are preparing a Feather Styling Razor with a compatible guarded blade. What should guide your preparation and cleanup?

A

Cut every section dry and save used blades that still feel sharp.

B

Wet every section and discard the blade with loose hair clippings.

C

Select the moisture conditions for the tool and technique, keep its guard in place, and discard the used blade in the designated sharps container.

D

Remove the guard and disinfect the disposable blade for the next client.

Sections you finish are checked off in the contents.