4.3 Salon Electrical Safety, Circuits & Electrotherapy Modalities

Key Takeaways

  • Electric current measures the rate of charge flow. DC has one direction. At 60 Hz, AC completes 60 cycles per second.

  • Volts measure potential difference, amperes measure current, ohms measure resistance, watts measure power and kilowatt-hours measure energy.

  • Fuses and breakers protect against overcurrent. A GFCI interrupts when it detects leakage through a current imbalance. Maintain protective grounding and keep equipment dry.

  • Verify which mode, electrode, setting, and conductive product the manufacturer specifies. Suitability and contraindications depend on the device.

  • Match a gel system to its curing lamp. An LED can emit ultraviolet or visible light. Georgia requires approved implement reprocessing before storage in a UV cabinet.

Last updated: November 2026

4.3 Salon Electrical Safety, Circuits & Electrotherapy Modalities

Use a tool only in the environment and configuration for which it is rated. Read its nameplate and check the plug and cord before use. A cordless tool and its wall charger can have different input and output requirements.

Current, Circuits and Units

An electric current is a rate of charge flow. Electrons carry charge in metal conductors. Ions can carry charge in a liquid. Copper in a cord conducts current, while its intact insulation helps keep people from making contact with the conductors. Moisture can make unintended paths for current. In a simple circuit, closing the switch completes the path through the load. Opening it interrupts that path. Switching a tool off does not necessarily de-energize everything upstream of its switch.

Direct current (DC) has one direction, although its size can vary. A battery can supply DC. Alternating current (AC) changes direction periodically. The nominal U.S. supply frequency of 60 Hz means 60 complete cycles each second, with two changes of direction per cycle for a sinusoidal current. A clipper charger may use a rectifier to convert AC to DC. An inverter converts DC to AC. Use the charger and power source specified for the model. Electric current, AC and DC and DOE on power conversion

UnitMeasuresUseful relation
Volt (V)Electric potential differenceOne volt is one joule per coulomb.
Ampere (A)CurrentOne ampere is one coulomb per second.
Milliampere (mA) or microampere (µA)Smaller current units1 mA = 0.001 A = 1,000 µA.
Ohm (Ω)ResistanceFor an ohmic load, current is voltage divided by resistance.
Watt (W) or kilowatt (kW)Power, the rate of energy transfer1 W = 1 joule per second. 1 kW = 1,000 W.
Kilowatt-hour (kWh)EnergyRunning a constant 1 kW load for one hour uses 1 kWh.

For a simple resistive load, use I=V/RI=V/R and P=VIP=VI with compatible voltage and current values. There is no rule requiring a voltage value to be numerically greater than its resistance value. For a real motor or electronic device, use the labeled input requirements when planning the outlet and circuit. NIST SI units, Ohm’s law and power and energy

Worked load decision. Two tools are each labeled 12 A. If both draw their rated current on the same 15 A branch circuit, the combined demand is 24 A, above the circuit rating. Two different outlets can share that circuit. Stop using that combination and have the circuit assignment confirmed. A breaker’s rating does not predict the exact moment it will trip. OSHA wiring and circuit protection

Match the Safety Device to the Hazard

ProtectionWhat it does
Fuse or circuit breakerOpens the circuit in response to overcurrent. A fuse element opens and must be replaced correctly; a breaker can be reset only when the equipment and circuit can be safely energized.
Equipment groundingProvides a low-impedance fault path back to the source so fault current can operate the protective device. It does not carry the normal load. Do not remove the grounding pin or defeat the ground connection.
Ground-fault circuit interrupter (GFCI)Compares outgoing and returning current. If enough current flows by an unintended path, it interrupts power. It reduces shock risk from leakage. It may not detect a shock if all current returns through the monitored conductors.
Dryer’s immersion protectionA compliant hand-supported hair dryer incorporates protection to reduce the risk if the dryer contacts water. Keep the dryer away from water and use the building’s required circuit protection as well.

Work with dry hands and equipment. Remove damaged equipment from service and report an unexpected trip. Follow the facility's safe procedure to determine whether the equipment and circuit can be energized. Repeatedly reclosing a breaker or replacing a fuse to continue operation is prohibited in covered workplaces. OSHA use of equipment, OSHA GFCI explanation and CPSC hair dryer requirements

Georgia’s State Minimum Standard Electrical Code uses the 2023 National Electrical Code with Georgia amendments effective January 1, 2026. NEC 210.8(B) applies to covered installations other than dwellings, including specified receptacles and equipment near sinks and in damp or wet locations. Use the applicable electrical code and local enforcement for the salon’s actual installation. Chapter 240-4 contains facility and sanitation rules. It is not the source of the GFCI installation requirements. Georgia DCA current codes, state electrical amendments, NFPA 210.8(B) record and Georgia Board rules

Electrical Treatments: Follow the Named Model

  • Galvanic facial equipment uses direct current through electrodes. In an externally powered electrolytic setup, the cathode is negative. A reduction reaction can generate hydroxide when water is reduced. The equipment and solution determine conditions at the electrode. For example, the Universal Companies DermiSystem C2000T directions specify the negative setting and a designated solution for desincrustation, a cosmetic step intended to soften sebum before removal. Consult the manual for the electrode and product. Do not infer polarity from wire color or assign a pore-opening, circulatory or nerve effect from the polarity alone.
  • Iontophoresis uses an electric field to assist transport. Which polarity is used depends on the material and device. A purpose-specific medical iontophoresis device has indications and directions separate from a cosmetic facial instrument. Do not use a cosmetic device for drug delivery.
  • Microcurrent describes small currents, commonly expressed in microamperes. The FDA record for NuFACE FIX+ identifies its specific cosmetic facial stimulation indication. A laboratory result for ATP in rat skin cannot establish a human salon outcome. Use the indicated site and manual. Defer unexplained swelling for assessment.
  • High-frequency glass-electrode equipment is a different device category. Some systems supply glass electrodes of different shapes and accessories for the maker’s direct or indirect modes. Carlton CC2311, for example, identifies a model-specific indirect electrode and insulated handle. Electrode glow does not establish acne treatment, implement disinfection or a safe ozone dose. Inspect the applicator and use only the specified attachment, method and settings.
  • Screen first. Confirm the site, contact medium, settings, contraindications and cleaning method in the manual. Check for factors such as an implanted electronic device or compromised skin as directed for the specific equipment. Defer if safe use cannot be established or if the proposed service is outside the license. Georgia’s definition of esthetics excludes diagnosing or treating dermatological conditions, medical aesthetics and use of lasers. O.C.G.A. § 43-10-1(8)

DermiSystem C2000T manual, electrolysis example, FDA iontophoresis device information, FIX+ FDA record, rat-skin experiment, Carlton CC2311, NIOSH ozone health information and NCI lymphedema guidance

Visible, Infrared and Ultraviolet Light

BandSalon application or safety consideration
VisibleThe human eye detects this band. The CND Visible Light Lamp is designed to cure compatible products with visible light. A skin-device indication is determined by the specific model and settings rather than the light’s color alone.
Infrared (IR)Longer wavelengths than visible light. Energy absorbed from an IR heat source can warm a surface. Use the specified distance, exposure and eye protection for the particular device. Example of infrared equipment instructions
Ultraviolet (UV)Shorter wavelengths than visible light. Some gel curing devices emit UV. Use the lamp intended for the gel system and its exposure instructions. UV can injure skin and eyes. A UV cabinet can store reprocessed implements labeled as required by Georgia Rule 240-4-.05. Its lamp does not perform the required cleaning or disinfection.

LED describes the light source, not its wavelength. Check the manufacturer’s specified lamp, compatible products, exposure time and protection. Do not use a nail curing lamp as an implement disinfectant or as a skin treatment device. NASA spectrum overview, FDA ultraviolet safety, measured emissions from nail curing devices, CND visible light lamp and Georgia Rules 240-4-.04 and .05

Test Your Knowledge

Which unit is equal to one-thousandth of an ampere?

A

Kilowatt.

B

Ohm.

C

Volt.

D

Milliampere.

Test Your Knowledge

A faulty appliance lets some current leave by a path outside the normal supply and return conductors. What does a functioning GFCI detect?

A

An increase in the AC supply frequency.

B

A difference between outgoing and returning current.

C

The need to raise the voltage of the receptacle.

D

The type of fuse inside the appliance.

Test Your Knowledge

The DermiSystem C2000T manual calls for a desincrustation solution. Which instruction matches that model’s desincrustation mode?

A

Select a setting by the color of the lead without checking its mode.

B

Use its positive setting regardless of the product or instructions.

C

Use its specified negative setting and the designated solution.

D

Use the nail lamp to activate the electrode.

Sections you finish are checked off in the contents.