11.2 Guidewires, Sheaths, Dilators & Microcatheters

Key Takeaways

  • Choose shaft support, tip flexibility, coating and geometry together. Observe distal response under imaging as the wire moves.

  • Follow each coating’s instructions for wetting and cleaning. Avoid prohibited metal edges, solvents and damaged surfaces.

  • Choose an exchange wire long enough for the path to the retained distal tip, external device travel and proximal sterile control.

  • Verify the sheath’s actual usable lumen, valve, outer profile and device compatibility, including the closure plan.

  • Match every coaxial or triaxial component by length, profile, pressure rating, intended agent and labeling.

Last updated: November 2026

11.2 Guidewires, Sheaths, Dilators & Microcatheters

Clinical Core: A guidewire establishes a rail, a dilator transitions into the tract, and a sheath maintains access while devices are exchanged. A microcatheter reaches a smaller target through a compatible outer catheter. Verify the complete chain from access needle to treatment device using the actual labels.

Guidewire mechanics and handling

Pushability describes transmission of forward force. Trackability describes how the wire or catheter follows a path. Torqueability describes transmission of rotation toward the tip. Radiopacity helps the operator identify the tip or marked segment under imaging. Distal response depends on core design, taper, coating, contact and the path through the vessel. Stop and report unusual motion, resistance or damage.

FeatureHow it informs selection
Core material and taperStainless steel can provide shaft support. Nitinol can recover from substantial bending and is used in kink-resistant designs. The dimensions and taper help determine distal flexibility and support.
Distal shape and flexible lengthStraight, angled and curved tips interact differently with an ostium or lesion. A Bentson design uses a flexible tip on a PTFE-coated stainless steel wire. A curved Rosen is another example. The exact geometry and length vary by model.
Shaft supportA wire such as a specified Amplatz or Lunderquist can provide a stiffer rail for delivery. Check the device-specific requirements and protect the monitored tip position.
Surface and visualizationDepending on the model, a wire can have a coil, a PTFE or hydrophilic surface, and a radiopaque tip or segment. Identify the visible marker and compare it with the working tip position.

Hydrophilic coatings reduce friction when prepared as labeled. Use the specified wetting or rinsing solution and do not use a damaged wire. For Terumo GLIDEWIRE GT, the manufacturer describes a heparinized physiological saline rinse before reinserting within the same procedure and permits wet gauze to remove remaining residue, as directed. Alcohol or solvents may damage the surface. The standard GLIDEWIRE instructions prohibit manipulation or withdrawal through a metal entry needle or metal dilator because the jacket can shear. A compatible plastic entry cannula is given as an option in those instructions. Report suspected coating separation or wire damage and follow the operator's plan.

Diameter and exchange length

Nominal diameterMetric equivalentExample of why the diameter matters
0.014 in0.36 mmSome coronary and other low-profile platforms use this size.
0.018 in0.46 mmSome micropuncture kits and peripheral delivery systems use this size.
0.035 in0.89 mmCommon size for diagnostic catheter exchanges and many peripheral platforms.
0.038 in0.97 mmSome diagnostic catheters and dilators accept this size. A wire lumen rated for 0.035 in is smaller.

Plan an over-the-wire exchange so the distal end stays in place while the full component is removed and the team maintains sterile control of the proximal end. Check the catheter or delivery system instructions for required length, diameter and permitted use of an extension. For example, Cook's Zenith iliac branch instructions name a 0.035-inch, 260-cm wire for particular exchange and delivery steps, while listing a 145-cm wire for some other tasks.

Worked exchange check. For a training setup, the team measures 105 cm of wire between the retained distal tip and its reference at the access site. Removing the old device completely outside that reference requires 100 cm, with 20 cm beyond it to allow control of the proximal end. That setup needs at least 105+100+20=225105 + 100 + 20 = 225 cm of usable wire. A compatible 260-cm wire meets the geometry and a 180-cm wire falls short. Confirm both devices' actual conditions, including hubs and working lengths, before clinical exchange.

Introducer sheath and dilator

A dilator fits the sheath and tapers toward the guidewire. It makes the transition from wire to sheath less abrupt. An access sheath can include a hemostatic valve, a sidearm and an imaging marker. The valve reduces backbleeding and air entry. Verify the approved preparation, monitor the seal and secure open ports. Sidearm flushing and pressure monitoring depend on the relevant circuit instructions and procedure. Confirm the undamaged dry or wetted setup, priming and connection specified for each model with the procedural team.

The marked introducer size describes its intended device compatibility. Look up the actual inner diameter and the maximum outer profile of the catheter or delivery system, including any part that has to cross the valve or distal tip. For the nominal 6 Fr Terumo Glidesheath Slender, the company lists body and tip inner diameters of 2.22 mm and 2.10 mm. A separate comparison lists a 2.44 mm outer profile for the 6 Fr Slender sheath and 2.62 mm for its standard 6 Fr comparison sheath. Outer profile influences access planning. For closure, use the closure device’s indications and its criteria for sheath size and arteriotomy.

The sheath length influences how far the tip can support the working device. Short introducers can stabilize entry and support nearby access. An appropriately selected longer curved sheath can support a crossover approach to the opposite limb. Long guiding systems can support a distal or tortuous route when there is sufficient working length. Confirm entry route, target, labeled compatibility and the remaining length for exchange.

Microcatheters and nested systems

A coaxial assembly places one catheter inside another. In a third catheter layer, a triaxial assembly adds an intermediate catheter between the outer guide or sheath and the inner catheter. The extra layer can provide support or aspiration where the indicated devices permit it. Each layer affects usable length and reduces the space available for the next device.

In the Terumo PROGREAT table, a 2.4/2.9 Fr version has a 0.022-inch inner lumen and a maximum guidewire diameter of 0.018 inch. A smaller wire alone does not establish that a coil or particle will pass. Verify the embolic agent or device, delivery lumen, pressure and intended use. Some wire-guided models can be shaped using the specified mandrel and method. Read the handling instructions for that model. A flow-directed design such as Marathon has a flexible distal section that can follow blood flow, and its labeling also specifies a maximum compatible guidewire and intended agents. Confirm the full device combination and watch the distal tip under imaging.

Loading diagram...
Wire, Sheath and Nested-Catheter Compatibility
Test Your Knowledge

The operator plans to reinsert a Terumo GLIDEWIRE GT in the same patient and procedure. After the labeled rinse, some blood residue remains. Which action follows the manufacturer’s handling instructions?

A

Scrub the shaft briskly with dry gauze.

B

Immerse the wire in isopropyl alcohol.

C

Scrape the residue with a metal instrument.

D

Wipe once with gauze moistened with heparinized physiological saline, and check the wire’s integrity.

Test Your Knowledge

Two introducer sheaths are marketed as 6 Fr. Which information is needed to decide whether a particular delivery catheter can pass and to anticipate the sheath’s access profile?

A

Verify the usable inner diameter and labeled compatibility of each sheath, and look up each sheath's actual outer profile.

B

Use 2.00 mm as both the inner and outer diameter of every 6 Fr sheath.

C

Add exactly 2 Fr to calculate the outside profile of either sheath.

D

Use only the marked French size of each dilator.

Test Your Knowledge

A planned exchange requires 105 cm of wire to preserve the distal tip position, 100 cm to accommodate the old catheter completely outside the access reference, and 20 cm for proximal control. Which listed, otherwise compatible wire meets the measured conditions?

A

145 cm

B

180 cm

C

260 cm

D

200 cm

Sections you finish are checked off in the contents.