4.1 Sterile Technique, Surgical Scrubbing & Gowning
Key Takeaways
Choose asepsis and barriers for the procedure. Central catheter insertion has a specific full-barrier recommendation.
Use the labeled surgical scrub or rub method and complete the appropriate drying before gloving.
Keep device ends within the sterile field. Announce a breach and replace affected supplies.
Match reprocessing and room controls to the device instructions and the facility classification.
4.1 Sterile Technique, Surgical Scrubbing & Gowning
Prevent contamination at the access site and along the delivery pathway. Hand hygiene and appropriate cleaning reduce transfer during routine care. Sterile technique combines sterile supplies, antiseptic preparation and barriers to keep critical instruments and the prepared field from contacting nonsterile surfaces. Match the level of asepsis to the procedure. For example, CDC recommends a cap, mask, sterile gown, sterile gloves and a full-body sterile drape for central venous catheter and PICC insertion or guidewire exchange.
Prepare hands, gown and gloves
Remove rings, watches and bracelets before surgical hand antisepsis. Remove debris under fingernails as directed. Perform surgical hand antisepsis before putting on a sterile gown and gloves for a scrubbed procedure. Antisepsis reduces microorganisms on skin. Sterile gloves limit transfer when handling sterile materials.
| Method | Preparation and drying |
|---|---|
| Surgical scrub using antimicrobial soap | Follow the manufacturer's application time. CDC describes 2–6 minutes as usual. Rinse and dry using the approved sterile technique, keeping runoff from returning to the hands. Use a separate towel area for each arm without bringing the part that touched the forearm back to the hand. |
| Alcohol-based surgical hand rub with persistent activity | Follow the product's directions for prewash, nail cleaning, application and drying. CDC describes prewashing hands and forearms with a nonantimicrobial soap and drying them before application. After applying the rub, allow hands and forearms to air-dry fully before gloving. |
Handle the inner surface while putting on the gown with the assistance appropriate to its design. A commonly taught sterile area is the front from mid-chest to field level and the sleeves from above the elbows to the cuffs. Treat the back, neckline and axilla as outside that working area. Knit cuffs must be covered by the sterile gloves. During closed gloving, keep hands in the gown sleeves while seating the glove cuffs. Open or assisted gloving may be used when appropriate to the task and policy. Report a torn glove or contact outside the sterile zone, protect the field and replace the affected barrier or supplies.
Protect the field from set-up through use
Set up as close as practical to use. Inspect package integrity, processing indicators and relevant dating. Avoid touching sterile contents to the wrapper edge or carrying drapes and instruments below the established sterile working surface. A circulating team member presents supplies while the scrubbed person receives them without crossing an unsterile boundary. Before moving equipment, confirm the status of barriers and keep long guidewires and catheter ends supported within the field. If fluid crosses a barrier or an item contacts a nonsterile surface, announce the breach, stop use of the affected area or equipment, and restore the field with the team before proceeding.
Select skin antisepsis for the site, allergy status and relevant guidelines. CDC recommends an alcohol-containing chlorhexidine preparation above 0.5% for central venous and peripheral arterial catheter insertion when chlorhexidine is suitable. Use an approved alternative when it is contraindicated. Follow the actual application and drying instructions. For example, the U.S. ChloraPrep Clear 26 mL label calls for complete drying before draping or applying an ignition source, with at least three minutes on hairless skin, and warns against pooling. Preparation of the access site and surgical hand preparation use separate products and instructions.
Worked case. A coiled wire is still on the table, but its distal end brushes the undraped detector during C-arm repositioning. Keep the contaminated wire away from other equipment, alert the operator, replace it with sterile equipment and check any surface it subsequently touched. When the sterile boundary is uncertain, resolve the uncertainty before returning the equipment to use.
Choose the appropriate reprocessing and room controls
| Item category | Required handling |
|---|---|
| Critical, entering sterile tissue or the vascular system | Use sterile devices. Reprocess reusable equipment only with validated instructions for that item. |
| Semicritical, contacting mucosa or nonintact skin | At least high-level disinfection, with any higher level required by the device or use. |
| Noncritical, contacting intact skin | Clean and disinfect according to the equipment instructions and exposure. |
Steam is preferred for compatible heat- and moisture-tolerant critical items. Low-temperature options for compatible items include ethylene oxide with required aeration and validated hydrogen peroxide systems. Cycle conditions and lumen restrictions depend on the equipment and devices. A chemical indicator records exposure to one or more process conditions. Facilities also use mechanical and biological monitoring. A wet, torn or punctured package requires resolution before sterile use.
The ventilation standard depends on room classification and local adoption. ASHRAE/ASHE 170-2025 Addendum y lists positive pressure, four outdoor and 20 total air changes per hour for a Class 3 imaging room. Engineering and infection prevention verify the facility's actual classification and operating conditions. A positive-pressure procedural room has a different purpose from a negative-pressure airborne isolation room.
A guidewire tip brushes the undraped detector during repositioning. What action protects the field?
Wipe the contacted end and continue without interrupting.
Continue because most of the wire stayed on the table.
Isolate the affected wire, announce the breach and evaluate anything it later touched.
Cover the contacted detector and return the same wire to the field.
An alcohol-based surgical hand rub has been applied according to its label. The forearms are still wet. What is the next step?
Allow the product to dry fully before putting on sterile gloves.
Pat the rubbed surfaces dry immediately with a sterile towel.
Put on gloves while the hands are wet to retain contact time.
Rinse off the rub while leaving the forearms wet.
Which principles apply when selecting reprocessing for an instrument that enters a blood vessel?
It is semicritical, so high-level disinfection is always enough.
It is critical and must be sterile, using validated instructions if reusable.
It becomes noncritical when handled only by gloved staff.
A color change on the package alone proves that every process requirement was met.
Sections you finish are checked off in the contents.