4. Troubleshooting Common Equipment Issues
Key Takeaways
Troubleshoot in a fixed order: patient first, then connections, then machine, then environment.
Assess the patient immediately when a trace goes flat. Begin the indicated emergency response without waiting for lead troubleshooting; if the patient is responsive and well, check the signal path.
An isolated change can help locate a signal problem, but review the shared electrodes and any leads-off messages before replacing a part.
Intermittent signal can result from a loose electrode, connector, or damaged cable. Check the accessible connections, then use approved off-patient testing or a known-good compatible spare.
Never open the case, splice a cable, or perform internal recalibration; tag out faulty equipment and submit a work order to biomedical engineering.
When a tracing goes wrong, work systematically: patient first, then connections, then machine, then environment. Checking the patient before the equipment is both a safety rule and an exam theme — never troubleshoot a machine while assuming the patient is fine.
- Look at the patient. Talking? Breathing comfortably? Normal color?
- Check the signal path. Electrode to skin, lead wire to electrode, lead wires to patient cable, cable to machine — every link.
- Check the machine. Paper, settings, error messages, leads-off alerts.
- Check the environment. Nearby electronics, temperature, movement, phone use.
Straight Line in Every Lead
A flat line can reflect a disconnected signal, a recorder fault or asystole. Check the patient first. In an unresponsive adult with absent or abnormal breathing, summon emergency help and follow Basic Life Support (BLS) within your training. An uncertain pulse after a brief trained check calls for CPR, with an AED used as soon as available. The team can verify the monitor signal without delaying care. If the patient is responsive and well, check for leads-off alerts and inspect the cable and electrode connections.
One Lead Looks Flat
Lead III displays the potential at the left leg relative to the left arm. It can appear nearly flat when the projected signal is small, so a near-flat Lead III alone does not establish a damaged wire. A faulty limb electrode can affect multiple displayed leads. For example, if a specific V4 lead-off alert appears and other channels remain usable, start with the V4 snap, skin contact and lead wire. Correct the connection and repeat the quality check per policy.
Intermittent Signal
Look for dried adhesive, loose snaps, or an unsecured connector. If the dropout persists, substitute a known-good compatible part if permitted. Test the suspect cable off the patient with approved equipment or have clinical engineering inspect it. Repeated dropout during lead or connector movement indicates a fault to investigate, rather than proof of a broken conductor at a particular spot.
All 12 leads print a flat line, but the patient is sitting up, talking, and asking questions. What should you do first?
Call a code immediately because the tracing shows asystole
Replace the paper roll and reprint the tracing
Check for a recording problem, beginning with the patient cable and lead connections
Increase the gain to 20 mm/mV to amplify any hidden signal
No Power
If the machine will not turn on: confirm the battery status and connect it to AC power; verify the cord is seated at both ends; try an approved known-good supply if safe, and report any suspected outlet or circuit problem to the responsible staff. A machine that is dead on a charged battery and a known-good outlet is out of service — tag it and submit a work order.
Paper Jams
Stop printing, open the printer cover per the manufacturer's instructions, remove the roll, and clear every torn fragment — scraps left behind can damage the thermal printhead. Load the specified paper in the orientation shown by the manual and run a test strip to confirm clean printing. Repeated jams point to a mis-loaded roll or a worn mechanism and belong to biomedical engineering.
Freezes and Error Codes
Record the exact error code and message before doing anything else. Try the manufacturer-approved restart for the model. If the fault recurs, stop using the machine, tag it out, and report it to biomedical engineering with the code you recorded. Never keep a machine that freezes unpredictably in service — an unexplained shutdown can erase an in-progress tracing.
Technician Fixes Versus Escalation
| Technician-level fix | Never the technician's job |
|---|---|
| Replace electrodes, lead wires, and paper; re-seat connectors | Opening the case or any internal repair |
| Clear a paper jam and reload the roll per instructions | Internal recalibration beyond printing and verifying the calibration mark |
| Re-prep skin and apply fresh electrodes | Servicing the printhead or acquisition module |
| Approved restart for a freeze; record the error code | Clearing an error code and returning a faulty machine to service without reporting |
Tag Out, Report, Document
Equipment that fails at the bedside and cannot be corrected leaves service immediately: attach a do not use tag, record the symptom and any error code, submit the work order to biomedical engineering, and switch to a backup machine. A repaired unit returns to service only after biomedical engineering clears it. This closes the loop on every fault you found in the Maintenance and Inspection section.
Where the Deeper Artifact Teaching Lives
This chapter covers equipment faults: broken hardware, power, paper, and connections. The patient-caused and environment-caused tracing distortions — somatic tremor, AC (alternating current) interference, and wandering baseline — are taught with their recognition patterns and fixes in the Cardiac Testing chapter's artifact section. Use that chapter when the tracing is ugly but every wire, cable, and connection checks out fine.
Scenario: Flat Everything
During a pre-stress-test recording, all 12 leads print a flat line. The patient is sitting up, chatting, and visibly fine — so the technician checks the signal path. The machine shows a leads-off alert, and the fault turns out to be the patient cable trunk not fully seated in the acquisition module. Re-seating it restores every lead. The same flat strip on a patient who had just become unresponsive would call for immediate patient assessment, an emergency call and indicated BLS rather than delay for equipment checks.
The display shows a V4 lead-off alert. The patient is responsive, and the other chest channels show usable signals. Which part of the hookup should you inspect first?
The V1 chest lead
The V4 electrode contact, connector and lead wire
The printer head
The charging cord
Which repair is never appropriate for the EKG technician to attempt?
Replacing a damaged lead wire with a tested spare
Clearing a paper jam and reloading the roll per the manufacturer's instructions
Re-seating a loose cable connector at the machine
Opening the machine case to repair internal components
Sections you finish are checked off in the contents.