All Practice Exams

Free Practice Questions for Master Plumber

Exam-style questions and explanations by OpenExamPrep.

✓ No registration✓ No credit card
198+ Questions
100% Free
Exam Review

Key Facts: Master Plumber Exam

70%

Passing Score

ICC contractor/trades

100

Questions

ICC G24/F24 bulletin

4 hrs

Time Limit

ICC G24/F24 bulletin

$120

Exam Fee

ICC via Pearson VUE

2018 IPC

G24 Reference Code (F24: 2015 IPC)

ICC bulletin

ICC's G24 Master Plumber exam has 100 multiple-choice questions, a 4-hour open-book time limit and a $120 fee through Pearson VUE, and most ICC contractor/trades exams require 70% to pass. Administration and general regulations make up 46% of the questions. State and local boards decide license eligibility, and some use their own IPC- or UPC-based exams.

Sample Master Plumber Practice Questions

Try these sample questions to review concepts for the Master Plumber exam. Each question includes a detailed explanation. Start the interactive quiz above for the full 198+ question experience with AI tutoring.

1According to the 2024 IPC, what is the minimum horizontal distance required between a water supply well and a septic tank?
A.25 feet
B.50 feet
C.75 feet
D.100 feet
Explanation: The widely adopted minimum horizontal separation between a private potable water well and a septic tank is 50 feet (a drain field/leach field is typically 100 feet). This is governed by state and local health/onsite-wastewater codes and EPA/HUD guidance rather than by the IPC itself, but 50 feet is the figure most jurisdictions and master plumber exams use for a well-to-septic-tank setback. Exam tip: 50 feet well-to-tank, 100 feet well-to-drainfield.
2Under both the IPC and UPC, what is the maximum static water pressure permitted in a building water distribution system before a pressure-reducing valve must be installed?
A.60 psi
B.80 psi
C.120 psi
D.160 psi
Explanation: Where the static water pressure supplied to a building exceeds 80 psi, an approved pressure-reducing valve (with strainer) must be installed to reduce the pressure to not greater than 80 psi static. This requirement appears in the IPC (Section 604.8) and the UPC (Section 608.2). Excessive pressure causes leaks, fixture damage, water hammer, and high water use, so 80 psi is the universal threshold tested on master plumber exams.
3What does the IPC require for the minimum slope of a 4-inch horizontal drainage pipe?
A.1/16 inch per foot
B.1/8 inch per foot
C.1/4 inch per foot
D.1/2 inch per foot
Explanation: Per 2024 IPC Table 704.1, horizontal drainage piping shall slope at not less than 1/4 inch per foot (2%) for pipes 2-1/2 inches and smaller, not less than 1/8 inch per foot (1%) for pipes 3 to 6 inches, and not less than 1/16 inch per foot for pipes 8 inches and larger. A 4-inch drain therefore requires a minimum of 1/8 inch per foot. The reduced slope for larger pipes is permitted because the larger diameter provides adequate scouring velocity at the lesser slope.
4A master plumber is reviewing plans for a multi-story building. According to the IPC, where must accessible plumbing fixtures be provided?
A.Only on the ground floor
B.On each floor having public toilet facilities
C.Only in employee break rooms
D.At the discretion of the building owner
Explanation: 2024 IPC Section 1101.2 requires that where plumbing fixtures are provided on a floor, accessible plumbing fixtures shall be provided on that floor. The ADA and ICC A117.1 standards work in conjunction with the IPC to ensure accessibility. This applies to public and common use toilet rooms, and includes accessible water closets, lavatories, and urinals where those fixtures are provided.
5What is the purpose of an air gap in a plumbing system according to code requirements?
A.To increase water pressure
B.To prevent backflow contamination
C.To reduce noise in pipes
D.To allow thermal expansion
Explanation: An air gap is the physical separation between the free-flowing discharge end of a potable water supply line and the flood level rim of a receiving fixture. Per 2024 IPC Section 608.15.1, air gaps provide the most reliable protection against backflow because they create an unobstructed vertical distance that prevents contaminated water from being siphoned back into the potable water supply. The required air gap is twice the effective opening of the supply pipe.
6Under the 2024 IPC, what is the minimum required size for a building drain serving a single-family dwelling?
A.2 inches
B.3 inches
C.4 inches
D.6 inches
Explanation: 2024 IPC Section 710.1 requires that the building drain shall be not less than 3 inches in diameter for a single-family dwelling. The building drain receives waste from all fixtures in the building and conveys it to the building sewer. For larger buildings or those with multiple dwelling units, the building drain size must be increased based on the total fixture units being served, as determined by the IPC drainage fixture unit tables.
7According to plumbing code, what is the maximum temperature for hot water delivered to public lavatories to prevent scalding?
A.100°F
B.110°F
C.120°F
D.140°F
Explanation: 2024 IPC Section 607.21 (Tempered water for public hand-washing facilities) requires the hot water delivered from public lavatories to be limited to not greater than 110°F (43°C) by a temperature-limiting device conforming to ASSE 1070/ASME A112.1070/CSA B125.70. This protects users from scalding. Tempered water is defined as 85°F to 110°F; private lavatories are not held to this 110°F cap.
8A master plumber must determine the required size for a vent stack serving a 10-story building. Which factor is MOST critical in this calculation?
A.The total fixture units on each floor only
B.The developed length of the vent and total drainage load
C.The diameter of the building drain only
D.The number of bathrooms in the building
Explanation: Vent stack sizing per 2024 IPC Section 916 requires consideration of both the developed length of the vent and the total drainage load being served (in fixture units). Longer vent lengths create more friction loss and require larger diameters to maintain adequate air circulation. The IPC vent sizing tables correlate these factors. Simply counting fixtures or knowing the drain size alone is insufficient for proper vent sizing in multi-story buildings.
9What is the minimum burial depth for a building sewer installed outside the building in a climate zone where the frost line is 30 inches?
A.12 inches
B.24 inches
C.30 inches
D.36 inches
Explanation: Per 2024 IPC Section 712.2, building sewers shall be installed at a minimum depth of 12 inches below finish grade, or below the frost line, whichever is greater. In areas with a 30-inch frost line, the sewer must be buried at least 30 inches deep to prevent freezing. Additionally, proper bedding and backfill are required to protect the pipe from damage. Deeper burial may be needed in areas with heavy vehicle traffic.
10Under the IPC, which of the following materials is NOT approved for use in a drainage system?
A.PVC Schedule 40
B.ABS Schedule 40
C.Galvanized steel for underground use
D.Cast iron hubless
Explanation: 2024 IPC Section 702 prohibits the use of galvanized steel pipe or fittings for underground drainage systems. Galvanized steel is susceptible to corrosion from soil conditions and the waste products conveyed. Approved materials for drainage include PVC Schedule 40, ABS Schedule 40, cast iron (hub and spigot or hubless), copper DWV, and certain approved plastics. Above ground, galvanized steel may be used in some applications with proper protection.

About the Master Plumber Exam

The Master Plumber exam tests the code knowledge needed for a master-level plumbing license. ICC's national G24 Master Plumber exam (2018 International Plumbing Code) and F24 National Standard Master Plumber exam (2015 IPC) each have 100 multiple-choice questions in a 4-hour open-book test across seven content areas, led by administration and general regulations at 46%. State boards that give their own exam may base it on the IPC or the UPC and set their own experience requirements.

Exam sponsor: PSI / ICC / State Licensing Boards. The requirements and fees below concern the certification or admission exam, separate from our free practice resources.

Questions

100 questions

Time Limit

4 hours

Passing Score

70%

Exam / Certification Fees

$120 (ICC G24/F24 through Pearson VUE)

Exam sponsor website

Fees, eligibility, and exam policies can change. Confirm them with the exam sponsor before applying or paying.

Our practice resources: topics covered

We aim to reflect publicly available exam outlines and topic information in our study resources. Coverage, format, and difficulty may differ from the actual exam, and we cannot guarantee that every detail is accurate or current. Confirm exam requirements, fees, and policies with the official exam sponsor.

46%

Administration and General Regulations

General installation requirements, code definitions and terms, plan reading, testing, and materials

14%

Plumbing Fixtures

Water heaters, water closets and urinals, specialty fixtures, and bathtubs, showers, sinks and lavatories

11%

Water Supply and Distribution

Service distribution and piping, water supply and pressure, and protection of the potable water supply

11%

Sanitary Drainage

Building sanitary drainage, sumps and ejectors, and indirect and special waste systems

8%

Plumbing Vent Requirements

Vent connections and grades, and vent terminals

8%

Traps, Interceptors, and Separators

Installation of traps, interceptors and separators

2%

Storm Drainage

Storm drainage

Preparing for the Master Plumber Exam

What You Need to Know

  • Passing score: 70%
  • Exam length: 100 questions
  • Time limit: 4 hours
  • Exam / certification fees: $120 (ICC G24/F24 through Pearson VUE) Official sources

Using Our Practice Resources

  • Work through all 198 available questions
  • Review every answer and explanation
  • Track weak areas and revisit them
  • Use our AI tutor for tough concepts

Master Plumber: Suggested Study Strategy

1Master multi-story building DWV design - vertical waste stacks and venting in tall buildings
2Practice commercial water supply sizing including booster pump calculations
3Study plumbing business law including contracts, liens, and contractor liability
4Understand complex isometric drawings for multi-fixture commercial layouts
5Know advanced backflow prevention including RPZ and DCVA applications
6Review gas pipe sizing for commercial systems with multiple appliances and regulators
7Practice with timed exams - master exams are longer and more complex
8Study special waste systems including grease interceptors, acid waste, and medical gas
9Understand medical gas piping requirements if included in your state exam

Frequently Asked Questions

How hard is the Master Plumber exam?

ICC does not publish pass rates for its master plumber exams. The G24 exam has 100 questions in 4 hours, open book, and most ICC contractor/trades exams require 70 percent correct. The time limit leaves no room to look up every answer, so you need to know the code's layout well.

What experience is required to take the Master Plumber exam?

Most states require 2-5 years of documented experience as a licensed journeyman plumber before you are eligible for the master exam. Some states also require proof of completed projects, continuing education credits, or business operation experience. Check with your state licensing board for specific requirements.

What is the passing score?

ICC contractor/trades exams such as G24 Master Plumber generally require 70 percent of the questions answered correctly, and G24 has 100 multiple-choice questions. State boards that give their own master plumber exam set their own passing score and length, so check your board's candidate bulletin.

Can I use code books during the exam?

Most states allow bound copies of the IPC or UPC during the exam, but some may have restrictions or provide their own references. No loose papers, handwritten notes, or electronic devices are permitted. Business law questions typically do not allow reference materials. Check with your specific state board for approved reference materials.

What makes the master exam different from the journeyman exam?

The master exam focuses on supervision, business operations, and complex design scenarios rather than basic installation skills. You will see questions about plumbing business law, contractor liability, multi-story building designs, commercial system sizing, and advanced code interpretation. The exam assumes you already know journeyman-level material and tests your ability to apply it at a higher level.

How many questions are on the Master Plumber exam?

ICC's G24 Master Plumber and F24 National Standard Master Plumber exams each have 100 multiple-choice questions with a 4-hour time limit. Administration and general regulations make up 46 percent of the questions, followed by plumbing fixtures at 14 percent. State-run exams can differ, so confirm the length with your licensing board.