Unilateral, Bilateral & Post-Reconstruction Measurement Techniques
Key Takeaways
For a unilateral mastectomy fitting, measure the intact hemithorax from the anterior mid-sternum to the posterior mid-spine and multiply by 2 for both the under-bust and over-bust calculations.
Under the traditional +4/+5 band conversion rule, add 4 inches to an even full under-bust measurement and add 5 inches to an odd full under-bust measurement; subtract the calculated band size from the full over-bust measurement to find the cup differential (0 in. = AA, 1 in. = A, 2 in. = B, 3 in. = C, 4 in. = D, 5 in. = DD/E, 6 in. = DDD/F).
In sister sizing, decreasing the band by one size (-2 in.) requires increasing the cup by one letter (e.g., 38C to 36D) to maintain identical cup volume and numeric prosthesis size.
For bilateral mastectomy patients, measure the 360-degree under-bust for band size, measure the horizontal chest wall footprint width from the parasternal border to the anterior axillary line, and collaborate with the patient on cup size; for lumpectomy or reconstruction asymmetry, always fit the bra cup to the larger breast first.
Unilateral Mastectomy Measurement Protocol: The Half-Chest (Hemithorax) Method
In a patient who has undergone a unilateral mastectomy without breast reconstruction, wrapping a tape measure around the full chest at apex level spans one intact breast and one flat surgical chest wall. Because half of the anterior breast projection is missing, a full-circumference over-bust measurement severely underestimates the patient's true cup volume and would lead the fitter to select a bra cup that compresses the natural breast and a prosthesis that is several sizes too small.
To eliminate the distortion caused by unilateral tissue loss, fitters use the Half-Chest (Hemithorax) Measurement Protocol (DCO task 3.A.1.b names half-measurements as a measurement technique), which captures measurements on the unaffected (intact) side from the anterior mid-sternum to the posterior mid-spine and doubles that value to reconstruct a symmetrical full-thorax circumference:
Step 1: Under-Bust (Band Size) Calculation and the Rule
- Position the non-stretch tape horizontally in the inframammary fold (IMF) directly beneath the intact breast, starting at the anterior mid-sternum (
0.0 in.) and wrapping around the intact ribcage to the posterior mid-spine. Multiply this half-chest reading by to obtain the Full Under-Bust Measurement (alternatively, if the surgical-side ribcage is completely healed and symmetrical at the IMF level, a direct under-bust ribcage circumference may be verified): - Because standard American and European bra band sizes are manufactured exclusively in even whole numbers (), apply the traditional Band Conversion Rule to the Full Under-Bust Measurement (many manufacturers now publish their own charts, which take priority):
- If the Full Under-Bust Measurement is an even number, add :
- If the Full Under-Bust Measurement is an odd number, add to reach the next even band size:
- Clinical Nuance for Large Ribcages () and High-Stretch Fabrics: Because modern elastane power-net bands stretch proportionally more over longer band lengths, adding or on a patient with a larger ribcage (e.g., a or raw under-bust) or in a high-stretch contemporary bra line can yield an overly loose band that rides up the back and allows the weight of a silicone prosthesis to pull the front downward. In these cases, fitters always verify the specific manufacturer's sizing chart and may apply a or conversion while confirming a firm, horizontal two-finger band fit during try-on.
Step 2: Over-Bust (Apex) Measurement
With the intact breast supported in a well-fitted, non-padded diagnostic bra, place the tape at the anterior mid-sternum at bust height, route it horizontally across the fullest apex (nipple prominence) of the intact breast to the posterior mid-spine, and multiply by :
Step 3: Cup Size Differential Calculation
Subtract the Calculated Band Size (from Step 1) from the Full Over-Bust Measurement (from Step 2):
| Cup Differential () | Resulting Bra Cup Size | Clinical Calculation Example |
|---|---|---|
| (or ) | AA cup | Full Over-Bust |
| A cup | Full Over-Bust | |
| B cup | Full Over-Bust | |
| C cup | Full Over-Bust | |
| D cup | Full Over-Bust | |
| DD (or E) cup | Full Over-Bust | |
| DDD (or F) cup | Full Over-Bust | |
| G cup | Full Over-Bust |
Note
Step-by-Step Unilateral Calculation Walkthroughs (Even vs. Odd Ribcage): Case 1 (Even Full Under-Bust):
- Half-chest under-bust (mid-sternum to mid-spine at IMF)
- Full Under-Bust (an even number add ) .
- Half-chest over-bust (mid-sternum over intact apex to mid-spine)
- Full Over-Bust
- Cup Differential C cup.
- Final Calculated Bra Size: .
Case 2 (Odd Full Under-Bust):
- Half-chest under-bust
- Full Under-Bust (an odd number add ) .
- Half-chest over-bust
- Full Over-Bust
- Cup Differential D cup.
- Final Calculated Bra Size: .
Sister Sizing Mechanics (Equivalent Cup Volume) and Prosthesis Cross-Reference Matrices
A foundational concept in prosthetic fitting is that bra cup letters are proportional to band size rather than representing a fixed volume. For example, the physical cup capacity of a 34C bra is substantially smaller than the cup capacity of a 40C bra. When a fitter adjusts a patient's band size up or down for torso comfort while needing to keep the exact same cup volume over the natural breast and prosthesis, the fitter applies Sister Sizing:
- Going DOWN One Band Size (): You must go UP one cup letter to preserve the same volumetric cup capacity (e.g., ).
- Going UP One Band Size (): You must go DOWN one cup letter to preserve the same volumetric cup capacity (e.g., ).
Therefore, the sister-size chain shares the exact same volumetric cup capacity (though the wire width and band length differ slightly across band sizes).
Manufacturer Prosthesis Cross-Reference Charts
External silicone breast prostheses (HCPCS L8030) are sized using a numeric scale (commonly Sizes 1 through 14 or 1 through 17) combined with a cup projection profile (Shallow / Profile 1, Average / Profile 2, or Full / Deep / Profile 3). Because sister sizes share equal cup volume, manufacturer cross-reference charts map a single numeric prosthesis size diagonally across sister-sized bra combinations. The chart below is illustrative only; each manufacturer publishes its own numeric scale:
| Numeric Prosthesis Size (Average Profile) | AA Cup Band | A Cup Band | B Cup Band | C Cup Band | D Cup Band | DD (E) Cup Band |
|---|---|---|---|---|---|---|
| Prosthesis Size 4 | 38AA | 36A | 34B | 32C | 30D | — |
| Prosthesis Size 5 | 40AA | 38A | 36B | 34C | 32D | 30DD |
| Prosthesis Size 6 | 42AA | 40A | 38B | 36C | 34D | 32DD |
| Prosthesis Size 7 | 44AA | 42A | 40B | 38C | 36D | 34DD |
| Prosthesis Size 8 | — | 44A | 42B | 40C | 38D | 36DD |
If a patient initially measures as a 38C (which cross-references to an Average-Profile Size 7 prosthesis), but during the fitting evaluation the 38 band feels too loose and rides up her back on a high-stretch bra model, stepping down to her tighter sister size 36D gives her a snugger band while still accommodating the exact same Size 7 breast prosthesis.
Bilateral Mastectomy and Lumpectomy/Reconstruction Asymmetry Protocols
1. Bilateral Mastectomy Measurement Protocol
When a patient has undergone a bilateral mastectomy without breast reconstruction, neither side retains a natural breast apex, making a standard over-bust differential calculation impossible. Instead, the Certified Mastectomy Fitter determines bra and prosthesis sizing through a three-part clinical protocol:
- Full Under-Bust Ribcage Circumference: Measure horizontally around the entire ribcage at the anatomical plane of the former inframammary fold (6th–7th rib level) and apply the band conversion rule (or manufacturer chart) to establish the patient's Band Size.
- Horizontal Chest Wall Footprint Width: Measure the linear horizontal width of the anterior hemithorax from the parasternal border ( to lateral to the mid-sternum) to the anterior axillary line. This width dictates the physical base footprint of the breast prostheses so that the forms cover the anterior pectoral chest wall naturally without extending laterally past the mid-axillary line, where they would collide with the inner upper arms during arm adduction.
- Collaborative Cup Volume and Profile Selection: Because the fitter is not constrained to matching a remaining contralateral breast, the cup size and projection profile become a shared clinical decision with the patient. The fitter evaluates the patient's pre-surgical cup size, height, shoulder width, overall body frame proportion, wardrobe goals, and musculoskeletal health (such as cervical spondylosis, osteoporosis, or lymphedema risk). Patients who wore very heavy
DDorDDDbreasts prior to bilateral surgery frequently elect to downsize to a balanced, proportionalBorCcup or choose lightweight silicone bilateral prostheses to eliminate chronic neck and shoulder strain while maintaining a natural silhouette.
2. Measuring for Lumpectomy, Radiation Retraction, or Reconstruction Asymmetry (Partial Shapers / Equalizers)
Patients who have undergone breast-conserving surgery (lumpectomy or quadrantectomy), radiation-induced parenchymal fibrosis and volume shrinkage, or autologous/implant breast reconstruction often present with significant asymmetry in volume, upper-pole fullness, or apex projection between the two breasts.
- The Golden Rule of Asymmetry Fitting: Always measure and fit the mastectomy bra cup to accommodate the larger breast first—regardless of whether the larger breast is the unoperated natural breast or an augmented/reconstructed breast. Never attempt to compress the larger breast into a smaller cup to match the smaller side.
- Volumetric Assessment of the Deficient Side: Once the larger breast is properly encapsulated inside its correct bra cup, examine the smaller or contour-deficient breast resting inside the opposite cup. Utilizing a graduated set of volumetric sizer shells or trial partial equalizers, the fitter fills the empty space in the deficient cup—selecting the specific partial prosthesis thickness, footprint, and quadrant shape (such as an upper-pole crescent filler, a lower-pole teardrop shaper, a lateral axillary filler, or a full-coverage shell overlay)—until both breasts exhibit identical forward projection, smooth cup tension, and level sternal-notch-to-apex symmetry under a close-fitting garment.
Tip
Fitting Strategy During Active Saline Tissue Expansion: When a patient is undergoing staged post-mastectomy tissue expansion (where the plastic surgeon injects to of sterile saline into a subpectoral or prepectoral expander port every to ), the volume of the expanding breast changes rapidly. Dispensing a definitive weighted silicone prosthesis (L8030) or custom form (L8035) during active expansion is clinically inappropriate because the form will quickly become the wrong size and Medicare only covers one silicone form per side every . Instead, fit a soft, non-restrictive bra to the larger/target breast size and provide an adjustable fiberfill puff (L8015/L8020) on the expanding side, instructing the patient how to remove small handfuls of polyester fiberfill after each saline injection until the permanent implant exchange and post-operative stabilization period are complete.
A Certified Mastectomy Fitter evaluates a patient 9 weeks after a left simple mastectomy. Using the half-chest measurement protocol on the intact right hemithorax, the fitter records a half-chest under-bust measurement of 16.5 inches and a half-chest over-bust apex measurement of 20.5 inches. Applying the traditional +4/+5 band conversion rule and cup differential scale, what is the patient's calculated bra size?
36DD
38C
34D
38B
During a diagnostic fitting, a unilateral mastectomy patient initially calculated at a 38C bra size (cross-referenced to an Average-Profile Size 7 silicone breast prosthesis) tries on a 38C pocketed mastectomy bra. The cup volume matches her intact breast and the Size 7 prosthesis perfectly, but the 38 band is too loose and rides up her back even on the tightest hook row. Which sister-sized bra should the fitter select to tighten the band by one size while maintaining the exact same cup volume for the Size 7 prosthesis?
36D
36C
40B
36B
A 58-year-old woman who underwent a bilateral total mastectomy without reconstruction 8 weeks ago presents for her first definitive prosthetic fitting. Because she has no remaining natural breast tissue to establish an over-bust apex reading, how should the Certified Mastectomy Fitter determine her bra and prosthesis sizes?
Take a 360-degree measurement across her flat upper chest at the level of the third rib and subtract her under-bust measurement to dictate a fixed mandatory cup size
Dispense the exact bra band, cup letter, and heavy weighted silicone volume that she remembers wearing 10 years prior to surgery without measuring her current thorax
Measure the circumference of her upper arm and multiply by 3 to estimate both her band size and bilateral prosthesis size
Measure the full under-bust for band, the chest wall footprint width for base size, then choose cup and profile with her
A patient who underwent a right breast-conserving lumpectomy and whole-breast radiation therapy 6 months ago presents with significant volume retraction and upper-pole hollowing of the right breast compared to her larger, unoperated left breast. What is the correct sequence for fitting this patient with a mastectomy bra and partial breast prosthesis (equalizer)?
Fit the bra cup to the larger left breast first, then use sizer shells in the right cup to choose a partial form
Fit two identical full-weight silicone breast forms over both breasts so the bra hides the underlying asymmetry
Measure and fit the bra cup to the smaller, radiated right breast first, and wear a compression minimizer panel over the larger left breast
Average the half-chest over-bust measurements of the right and left sides so the bra cup splits the difference between the two breasts
Sections you finish are checked off in the contents.