Free Practice Questions for SVP Auto Electrician

Exam-style questions and explanations by OpenExamPrep.

✓ No registration✓ No credit card

152+ Questions

100% Free

Loading practice questions...

Same family resources

Explore More Saudi SVP Automotive Skill Verification

Continue into nearby exams from the same family. Each card keeps practice questions, study guides, flashcards, videos, and articles in one place.

Saudi Skill Verification Program - Light Vehicle Mechanic

Practice Questions162 questions

Saudi Skill Verification Program - Diesel / Heavy Vehicle Mechanic

Practice Questions100 questions

Exam Review

Key Facts: SVP Auto Electrician Exam

100

Practice Questions

OpenExamPrep

Both parts

Pass Requirement

PACC: pass computer-based + practical; score not published

≤120 min

Computer-Based Test Time

PACC FAQ (varies by occupation)

Saudi Skill Verification Program - Auto Electrician prep course featuring 100 high-quality practice questions and detailed explanations.

Sample SVP Auto Electrician Practice Questions

Try these sample questions to review concepts for the SVP Auto Electrician exam. Each question includes a detailed explanation. Start the interactive quiz above for the full 152+ question experience with AI tutoring.

1A headlamp circuit has a resistance of 4 ohms and operates on a 12-volt battery. What is the current flowing through the headlamp?

A.0.33 Amperes

B.3 Amperes

C.16 Amperes

D.48 Amperes

Explanation: Using Ohm's Law (I = V/R), divide the voltage (12V) by the resistance (4 ohms) to find the current. This fundamental law is crucial for understanding electrical circuits and diagnosing faults.

2In a series circuit containing two resistors, R1 = 5 ohms and R2 = 10 ohms, connected to a 12-volt battery, what is the total resistance of the circuit?

A.50 ohms

B.15 ohms

C.120 ohms

D.3.33 ohms

Explanation: In a series circuit, the total resistance is the sum of individual resistances. R_total = R1 + R2. This principle is fundamental for analyzing voltage drops and current flow in series components common in automotive systems.

3Two parallel-connected bulbs are powered by a 12-volt battery. If bulb 1 has a voltage of 12 volts across it, what is the voltage across bulb 2?

A.0 volts

B.12 volts

C.6 volts

D.24 volts

Explanation: In a parallel circuit, the voltage across each branch is the same and equal to the source voltage, assuming no resistance in the connecting wires. This is a key characteristic distinguishing parallel from series circuits, vital for understanding accessory operation.

4A circuit wired in 16 AWG (about 1.3 mm2) cable supplies a load that draws 8 A continuously. Which standard ATO blade fuse should protect it?

A.10 A, red

B.5 A, tan

C.15 A, blue

D.25 A, clear

Explanation: A fuse protects the wire, not the load. Automotive wire/fuse tables put the maximum fuse for 16 AWG (1.31 mm2) at 10 A, and 10 A is also the next standard ATO rating above the 8 A working current, so it carries the load without nuisance blowing. In the ATO/ATC colour code 10 A is red.

5A starter motor circuit draws 200 Amperes. The battery cable resistance is measured at 0.005 ohms. What is the voltage drop across the battery cable?

A.40,000 Volts

B.1.0 Volt

C.0.1 Volt

D.0.0025 Volts

Explanation: Voltage drop is calculated using Ohm's Law (V = I * R). Multiplying the current (200A) by the cable resistance (0.005 ohms) gives the voltage lost across the cable. This drop reduces the voltage available to the starter motor and affects its performance.

6When measuring current in a circuit with a multimeter, how should the multimeter be connected?

A.In parallel with the circuit being measured

B.In series with the circuit being measured

C.To ground only

D.Across the power source

Explanation: An ammeter (multimeter in current mode) must be connected in series so that the entire current flows through it. Connecting it in parallel would likely short the circuit or blow the meter's fuse due to its very low internal resistance.

7Before arc-welding a bracket onto a vehicle body, what should the auto electrician do to protect the electronic modules?

A.Disconnect both battery leads and earth the welder near the weld

B.Switch the ignition off but leave both battery leads connected

C.Pull the fuses of the circuits nearest to the welding point

D.Hold the engine at a fast idle while the welding is done

Explanation: Welding current looks for the lowest-resistance path back to the welder. Disconnecting both battery leads isolates the alternator, control modules and harness, and clamping the welding earth within a short distance of the weld keeps the return current out of the vehicle wiring and bearings.

8What is the main purpose of a relay in an automotive electrical circuit?

A.A small current switches a large one

B.It raises the supply voltage to the load

C.It lowers the total resistance of the circuit

D.It stores energy for use during voltage dips

Explanation: A relay is an electrically operated switch. A few hundred milliamps through the coil closes heavy contacts that carry tens of amps, so a dashboard switch or a control module output never has to handle the load current of a starter, fuel pump or headlamp.

9A circuit has two 6-ohm resistors connected in parallel, and this combination is connected in series with a 3-ohm resistor. What is the total resistance of the circuit?

A.15 ohms

B.6 ohms

C.12 ohms

D.1.5 ohms

Explanation: The two 6-ohm resistors in parallel give (6 x 6) / (6 + 6) = 3 ohms. That 3 ohms is in series with the remaining 3-ohm resistor, so the total is 3 + 3 = 6 ohms.

10What typically happens when a direct short circuit occurs between a power wire and ground in an unprotected circuit?

A.The circuit opens immediately

B.System voltage rises sharply

C.Total circuit resistance rises sharply

D.Current rises and wiring overheats

Explanation: A dead short bypasses the load, so circuit resistance falls close to zero and I = V / R drives current to hundreds of amps. The energy goes into the wiring as heat, melting insulation and starting fires unless a fuse or circuit breaker opens first.

About the SVP Auto Electrician Exam

The Saudi Skill Verification Program (SVP) exam for Auto Electricians checks technical skills and theory covering basic electrical circuit schematics, starting and charging system maintenance, sensor diagnostic tools, and workshop WHS protocols.

Exam sponsor: Takamol Holding / Professional Accreditation Center (PACC), MHRSD. The requirements and fees below concern the certification or admission exam, separate from our free practice resources.

Assessment

Multiple-choice computerised exam administered by Takamol Holding / Professional Accreditation Center (PACC), MHRSD.

Time Limit

Varies by occupation; maximum 120 minutes for the computer-based test (PACC)

Passing Score

Not published by Takamol / PACC (candidates must pass both the computer-based test and the practical assessment)

Exam / Certification Fees

USD 50 outside Saudi Arabia; SAR 540.50 inside Saudi Arabia (PACC, per attempt, non-refundable)

Exam sponsor website

Fees, eligibility, and exam policies can change. Confirm them with the exam sponsor before applying or paying.

Official sources

Takamol Holding / Professional Accreditation Center (PACC), MHRSD: official exam information

Our practice resources: topics covered

We aim to reflect publicly available exam outlines and topic information in our study resources. Coverage, format, and difficulty may differ from the actual exam, and we cannot guarantee that every detail is accurate or current. Confirm exam requirements, fees, and policies with the official exam sponsor.

Not published

Electrical Circuits And Schematics

Practice questions covering electrical circuits and schematics.

Not published

Starting And Charging Systems

Practice questions covering starting and charging systems.

Not published

Automotive Sensors And Ecu

Practice questions covering automotive sensors and ecu.

Not published

Battery And Lighting Diagnostics

Practice questions covering battery and lighting diagnostics.

Preparing for the SVP Auto Electrician Exam

What You Need to Know

Passing score: Not published by Takamol / PACC (candidates must pass both the computer-based test and the practical assessment)
Assessment: Multiple-choice computerised exam administered by Takamol Holding / Professional Accreditation Center (PACC), MHRSD.
Time limit: Varies by occupation; maximum 120 minutes for the computer-based test (PACC)
Exam / certification fees: USD 50 outside Saudi Arabia; SAR 540.50 inside Saudi Arabia (PACC, per attempt, non-refundable) Official sources

Using Our Practice Resources

Work through all 152 available questions
Review every answer and explanation
Track weak areas and revisit them
Use our AI tutor for tough concepts

SVP Auto Electrician: Suggested Study Strategy

1Carefully study all regulatory and legislative requirements.

2Practice sample calculations and review real-world scenario items.

3Review the explanations for all incorrect practice questions to build core conceptual clarity.

Frequently Asked Questions

What is the passing score for SVP Auto Electrician?

Takamol and the Professional Accreditation Center (PACC) do not publish a numeric passing score for the Skill Verification Program. A worker must pass both the computer-based theory test and the practical assessment; failing the computer-based part after passing the practical means repeating the whole test. Up to three paid attempts are allowed.

Who administers the SVP Auto Electrician exam?

The Professional Accreditation Center (PACC), operating the Skill Verification Program for the Saudi Ministry of Human Resources and Social Development (MHRSD) with Takamol, administers the test through pacc.sa (and svp-international.pacc.sa for workers outside the Kingdom). The former svp.qiwa.sa address no longer resolves.