100+ Free PASMA Towers for Users Practice Questions

Pass your PASMA Towers for Users (Prefabricated Access Suppliers' and Manufacturers' Association, UK) exam on the first try — instant access, no signup required.

✓ No registration✓ No credit card✓ No hidden fees✓ Start practicing immediately

90% Pass Rate

100+ Questions

100% Free

Loading practice questions...

2026 Statistics

Key Facts: PASMA Towers for Users Exam

80%

Theory Pass Mark

PASMA

5 years

Card Validity

PASMA

17 mph

Wind Speed Limit

PASMA

Theory Questions

PASMA

950 mm

Min Guardrail Height

EN 1004

150 mm

Min Toeboard Height

EN 1004

The PASMA Towers for Users theory test consists of 30 multiple-choice questions with an 80% pass mark (24/30 correct). The certification is valid for 5 years and is legally required by many UK construction sites to demonstrate competence under the Work at Height Regulations 2005. The training requires physically assembling a tower and passing the closed-book theory assessment.

Sample PASMA Towers for Users Practice Questions

Try these sample questions to test your PASMA Towers for Users exam readiness. Each question includes a detailed explanation. Start the interactive quiz above for the full 100+ question experience with AI tutoring.

1Which UK legislation is the primary regulatory framework governing all activities involving work at height?

A.The Work at Height Regulations 2005

B.The Health and Safety at Work Act 1974

C.The Management of Health and Safety at Work Regulations 1999

D.The Construction (Design and Management) Regulations 2015

Explanation: The Work at Height Regulations 2005 (WAHR) apply to all work at height where there is a risk of a fall liable to cause personal injury. They place duties on employers, the self-employed, and anyone who controls the work of others to ensure that work is properly planned, supervised, and carried out by competent persons. The other acts are general safety and construction laws.

2What is the first step in the hierarchy of control specified under the Work at Height Regulations 2005?

A.Avoid working at height if possible

B.Prevent falls using collective protection

C.Minimize the distance of a fall using fall arrest equipment

D.Provide comprehensive training to all employees

Explanation: The hierarchy of control under the Work at Height Regulations 2005 explicitly requires that the first option considered must be to avoid working at height altogether (e.g., performing the work from the ground). If avoidance is not possible, the duty holder must prevent falls using collective measures, and only as a last resort minimize the consequences using individual fall arrest systems. Training is a supporting requirement, not a step in the hierarchy.

3Under the Work at Height Regulations 2005 hierarchy, which option must be prioritized over personal protection?

A.Collective protection (e.g., guardrails)

B.Personal fall arrest harnesses

C.Safety netting and air bags

D.Individual warning lines

Explanation: Collective protection measures that protect more than one person at a time (such as guardrails, barriers, or scaffold towers) must always be prioritized over personal protection measures (such as harnesses and lanyards). Collective protection does not require active user cooperation to prevent a fall, making it inherently safer and more reliable. Personal fall protection is only used when collective measures are not practicable.

4What is the current European product standard governing the design and manufacture of mobile access and working towers?

A.BS EN 1004

B.BS 1139-6

C.BS 5973

D.BS EN 12811

Explanation: BS EN 1004 (specifically BS EN 1004-1) is the European standard for prefabricated mobile access and working towers made of aluminum, steel, or other materials. It defines the design requirements, dimensions, safety features, and design loads. BS 1139-6 covers towers outside the scope of BS EN 1004 (such as cantilevers or bridges), while the other standards refer to traditional tube-and-fitting scaffolding.

5To which range of heights does the BS EN 1004-1:2020 standard apply for freestanding mobile access towers?

A.Platform heights from 0 meters up to 12 meters indoors and 8 meters outdoors

B.Platform heights from 2.5 meters to 12 meters indoors and 8 meters outdoors

C.Platform heights up to 20 meters indoors and 15 meters outdoors

D.Platform heights only above 2 meters up to 10 meters

Explanation: The latest BS EN 1004-1:2020 standard covers prefabricated mobile access towers with platform heights starting from 0 meters (meaning low-level platforms are now included) up to 12 meters indoors (where wind load is absent) and 8 meters outdoors (subject to wind loads). Towers outside these limits or with non-standard modifications are covered under BS 1139-6.

6Which standard covers prefabricated mobile access towers that fall outside the scope of BS EN 1004 (e.g., linked towers or cantilevered structures)?

A.BS 1139-6

B.BS EN 12811

C.BS 5973

D.BS 8411

Explanation: BS 1139-6 is the British Standard that applies to prefabricated mobile towers that incorporate non-standard configurations such as cantilevers, bridges between towers, linked structures, or heights exceeding the 12m indoor / 8m outdoor limits of BS EN 1004. Compliance with BS 1139-6 ensures that structural integrity and stability are verified through specific calculation standards.

7What is the maximum platform height permitted for a freestanding mobile access tower assembled outdoors under BS EN 1004?

A.8 meters

B.12 meters

C.6 meters

D.10 meters

Explanation: Under BS EN 1004, the maximum platform height for a freestanding (un-tied) mobile access tower outdoors is 8 meters. This limit is set because outdoor towers are exposed to wind loads, which significantly increase the risk of overturning. For indoor applications with no wind, the maximum height is 12 meters.

8What is the maximum platform height permitted for a freestanding mobile access tower assembled indoors under BS EN 1004?

A.12 meters

B.8 meters

C.15 meters

D.10 meters

Explanation: Under BS EN 1004, the maximum platform height for a freestanding mobile access tower indoors is 12 meters. This limit assumes the tower is protected from wind and other lateral environmental forces. Indoor towers exceeding this height must be designed by a structural engineer and are typically subject to BS 1139-6.

9Under the Health and Safety at Work Act 1974, who is responsible for ensuring that workers have received adequate training to use mobile access towers?

A.The employer

B.The equipment manufacturer

C.The employee

D.PASMA

Explanation: The Health and Safety at Work Act 1974 places the primary duty of care on the employer to ensure the health, safety, and welfare of their employees. This includes providing adequate information, instruction, training, and supervision, such as sending workers on a certified PASMA training course. While employees have a duty to cooperate, the employer holds legal responsibility for compliance.

10What duty does an employee have under the Health and Safety at Work Act 1974 regarding safety equipment like mobile access towers?

A.To use the equipment correctly in accordance with their training

B.To perform structural strength tests on the equipment

C.To modify components as needed for their daily tasks

D.To purchase their own replacement parts if components are damaged

Explanation: Employees have a statutory duty under Section 7 of the Health and Safety at Work Act 1974 to take reasonable care of their own safety and that of others, and to cooperate with their employer. This includes correctly using all work equipment, including mobile access towers, in accordance with the training and instruction provided.

About the PASMA Towers for Users Exam

The industry-standard qualification for assembling, dismantling, moving, and inspecting mobile access towers in the UK. This course ensures compliance with the Work at Height Regulations 2005.

Questions

30 scored questions

Time Limit

Closed-book written test

Passing Score

80%

Exam Fee

£100-£190 (PASMA)

PASMA Towers for Users Exam Content Outline

20%

Legislation, Regulations & Guidance

Work at Height Regulations 2005, PASMA Code of Practice

25%

Product Standards & Tower Components

BS EN 1004 standards, component checks, and stability

30%

Assembly & Dismantling Procedures

Step-by-step methods including 3T and AGR systems

25%

Safe Tower Use & Hazard Awareness

Outriggers, stabilizers, wind limits, and inspection records

How to Pass the PASMA Towers for Users Exam

What You Need to Know

Passing score: 80%
Exam length: 30 questions
Time limit: Closed-book written test
Exam fee: £100-£190

Keys to Passing

Complete 500+ practice questions
Score 80%+ consistently before scheduling
Focus on highest-weighted sections
Use our AI tutor for tough concepts

PASMA Towers for Users Study Tips from Top Performers

1Always read the manufacturer's instruction manual; it must be on-site during assembly and use.

2Understand the Work at Height Regulations 2005 hierarchy of control: avoid, prevent, minimize.

3Memorize key dimensions: minimum guardrail height of 950 mm, maximum gap of 470 mm, minimum toeboard of 150 mm.

4Remember the wind speed safety limit: cease work and do not erect or dismantle if wind exceeds 17 mph (27.3 km/h).

5Never stand on an unprotected platform; always use the 3T or AGR method to install guardrails first.

Frequently Asked Questions

What is the passing score for the PASMA theory test?

The passing score for the PASMA Towers for Users theory test is 80%. This means you must answer at least 24 out of 30 multiple-choice questions correctly. You must pass both the theory test and the practical assembly/dismantling assessment to receive your PASMA PhotoCard.

How long is a PASMA card valid for?

A PASMA PhotoCard and Certificate are valid for 5 years from the date of issue. To renew your card, you must take the training course and pass the assessments again to ensure you are up-to-date with current safety standards and regulations.

What is the difference between the 3T and AGR assembly methods?

The 3T (Through the Trapdoor) method involves the operator assembling and removing guardrails while seated safely within the platform trapdoor before stepping onto the platform. The AGR (Advance Guardrail) method uses pre-assembled guardrail frames installed from the level below, ensuring collective fall protection is already in place before the operator ascends.

What is the maximum wind speed for working on a mobile tower?

Work on a mobile access tower must cease, and the tower must not be erected, altered, or dismantled, if wind speeds exceed 17 mph (approx. 27.3 km/h, or Beaufort Force 4). If high winds are expected, the tower must be dismantled or secured by tying it to a solid structure.

How often does a mobile tower need to be inspected?

Under the Work at Height Regulations 2005, a mobile access tower must be inspected: 1) after assembly and before first use, 2) at least once every 7 days (weekly), 3) after any alteration or event likely to affect its stability (such as severe weather or an impact). The results must be recorded in a written tower inspection report.

Can I use adjustable legs to make a PASMA tower taller?

No. Adjustable legs are designed solely for leveling the mobile access tower on sloping or uneven ground. They must never be used to gain extra platform height. The maximum extension of the adjustable legs is specified in the manufacturer's instruction manual and must never be exceeded.