100+ Free SVP Steel Fixer Practice Questions

Pass your Saudi Skill Verification Program - Steel Fixer (Saudi Arabia) exam on the first try — instant access, no signup required.

✓ No registration✓ No credit card✓ No hidden fees✓ Start practicing immediately

100+ Questions

100% Free

Loading practice questions...

Same family resources

Explore More Saudi Skill Verification Program (SVP) Construction Trades

Continue into nearby exams from the same family. Each card keeps practice questions, study guides, flashcards, videos, and articles in one place.

2026 Statistics

Key Facts: SVP Steel Fixer Exam

100

Practice Questions

OpenExamPrep

50% (theory) + pass practical

Pass Score

Official Guidelines

2.0 hours

Time Limit

Exam Rules

Saudi Skill Verification Program - Steel Fixer prep course featuring 100 high-quality practice questions and detailed explanations.

Sample SVP Steel Fixer Practice Questions

Try these sample questions to test your SVP Steel Fixer exam readiness. Each question includes a detailed explanation. Start the interactive quiz above for the full 100+ question experience with AI tutoring.

1According to international and Saudi construction safety guidelines, at what height threshold must a steel fixer use a personal fall arrest system (PFAS) or safety harness on an unprotected platform?

A.1.8 meters (6 feet)

B.1.2 meters (4 feet)

C.3.0 meters (10 feet)

D.4.5 meters (15 feet)

Explanation: Standard occupational safety guidelines (such as OSHA and Saudi construction safety regulations) mandate fall protection systems, including personal fall arrest systems (PFAS), for workers exposed to fall hazards of 1.8 meters (6 feet) or higher above a lower level.

2Which combination of Personal Protective Equipment (PPE) is most critical specifically for a steel fixer carrying and placing rebar to prevent puncture and cut injuries?

A.Heavy-duty leather gloves and steel-toe safety boots with puncture-resistant steel midsoles

B.Cotton canvas gloves and standard rubber-soled athletic shoes

C.Latex gloves and steel-toed shoes without midsole reinforcement

D.Heavy leather gloves and rubber boots with composite toes only

Explanation: Steel fixers handle sharp, heavy, and hot steel reinforcement bars and work on surfaces with exposed tie wires. Heavy-duty leather gloves protect hands from cuts and heat, while steel-toe boots with puncture-resistant steel midsoles protect against stepping on wire offcuts and dropped bars.

3When working in the extreme summer heat of Saudi Arabia, what practice must a steel fixer follow to prevent heat stroke and dehydration while handling steel reinforcement?

A.Drink water or electrolyte solutions regularly (every 15-20 minutes) and use shaded rest areas during peak temperature periods

B.Drink large amounts of caffeinated energy drinks to maintain stamina and avoid resting to finish the pour

C.Only drink water when feeling extremely thirsty and work continuously through the afternoon

D.Wear thick wool garments to block out ambient heat and restrict liquid intake to avoid frequent restroom breaks

Explanation: Summer temperatures in Saudi Arabia can exceed 45 degrees Celsius, making steel hot to the touch and placing workers at extreme risk of heat-related illnesses. The Ministry of Human Resources mandates mid-day work bans in summer, and workers must hydrate every 15-20 minutes and rest in shaded areas to regulate body temperature.

4What is the safest protocol when lifting a bundle of reinforcing steel using a site crane?

A.Use double-leg slings spaced to balance the load, verify the weight is within the crane's capacity, and attach tag lines to control swing

B.Wrap a single wire rope sling around the center of the bundle and lift quickly to minimize block time

C.Secure the bundle with weak hemp rope and rely on workers to manually push the bundle during lifting

D.Always lift the load at an angle with one point higher to make it easier to land in narrow column cages

Explanation: Lifting rebar bundles requires double-leg web or chain slings placed at balanced intervals to prevent bars from slipping out. Checking the load weight and utilizing tag lines allows ground workers to steer the load safely from a distance, avoiding crushing hazards.

5A scaffold has a yellow inspection tag affixed to it at the access point. What does this indicate to a steel fixer?

A.The scaffold has been modified or is incomplete, presenting hazards; it requires special safety precautions or a safety harness to use

B.The scaffold is completely safe for general use without any additional safety equipment

C.The scaffold is unsafe and must not be accessed under any circumstances

D.The scaffold is reserved only for bricklayers and cannot be used by steel fixers

Explanation: In standard scaffolding tag systems, a green tag means safe to use, a red tag means unsafe/do not use, and a yellow tag means the scaffold has been modified, is under assembly, or requires specific PPE (like a safety harness tied off to an independent anchor point) to access.

6How should steel reinforcement bars be stored on a construction site to maintain safety and material quality?

A.Stacked on level timber dunnage off the ground, sorted by size and grade, and covered to protect from moisture and sand dust

B.Piled directly on wet soil to keep them cool and prevent thermal expansion in the sun

C.Stored upright against the excavation walls to save site space

D.Scattered across the active driving lanes so the delivery crane does not have to travel far

Explanation: Rebar must be kept off the ground on timber dunnage (sleepers) to prevent it from absorbing moisture and mud, which causes accelerated corrosion. Organizing them by size and grade prevents errors during fabrication, while covers prevent contamination from salt-laden sand dust.

7When operating an automatic rebar bending machine, what is the minimum safe distance the operator should maintain between their hands and the bending pin?

A.300 mm (12 inches)

B.50 mm (2 inches)

C.100 mm (4 inches)

D.20 mm (0.8 inches)

Explanation: Operating mechanical power benders poses a severe crush and amputation hazard. Operators must keep their hands at a safe distance (minimum 300 mm) from the rotating bending pin and mandrel, using helper tools or guides if bending short bars.

8What is the primary housekeepings hazard associated with steel fixing, and how should it be managed on a slab deck?

A.Tying wire offcuts and loose rebars causing slips and trips; managed by collecting scrap wire in bins and keeping walkways clear

B.Excessive dust from concrete; managed by constantly spraying water on the steel bars

C.Overhead crane cables; managed by pulling the cables down to tie them to the slab mesh

D.Excessive formwork oil; managed by washing the plywood with grease before placing steel

Explanation: Rebar installation creates debris, notably sharp tying wire offcuts and short steel bars. If left scattered on the formwork, these act as roller bearings underfoot, causing severe slip, trip, and puncture injuries. Regular clean-up and containerized disposal are essential.

9What is the correct manual lifting technique a steel fixer should use when lifting a heavy, individual reinforcement bar from a storage stack?

A.Bend the knees, keep the back straight, hold the bar close to the body, and lift using the leg muscles

B.Keep the legs straight, bend at the waist, and pull the bar up using the back muscles

C.Twist the torso dynamically while lifting to swing the bar onto the shoulder in one motion

D.Jerk the bar upward rapidly to utilize momentum and reduce load time

Explanation: Manual handling of rebar exposes workers to back strain. Bending the knees and keeping the back straight transfers the load to the large leg muscles, while keeping the bar close to the body reduces the lever arm force acting on the lumbar spine.

10When handling and carrying long steel reinforcement bars near overhead power lines, what is the minimum safe clearance distance that must be maintained?

A.6.0 meters (20 feet)

B.1.5 meters (5 feet)

C.3.0 meters (10 feet)

D.0.5 meters (1.6 feet)

Explanation: Long steel bars are highly conductive and can act as antennas or make accidental contact with power lines. Safety regulations generally mandate a minimum clearance of 6.0 meters (20 feet) from high-voltage lines, or de-energizing the lines before starting work.

About the SVP Steel Fixer Exam

The Saudi Skill Verification Program (SVP) exam for Steel Fixers checks technical skills and theory covering rebar types and grades, cutting and bending tools, wire tying methods, reading structural drawings, bar bending schedules (BBS), concrete cover, lap splicing, anchoring, safety protocols, and working at heights.

Assessment

Multiple-choice computerised exam administered by Takamol Holding / Professional Accreditation Center (PACC), MHRSD.

Time Limit

2.0 hours

Passing Score

50% (theory) + pass practical

Exam Fee

Varies by country (sponsored or employer-paid) (Takamol Holding / Professional Accreditation Center (PACC), MHRSD)

SVP Steel Fixer Exam Content Outline

20%

Safety Standards And Regulations

Practice questions covering occupational safety standards, personal protective equipment (PPE), hazard identification, working at heights, and heavy lifting protocols.

20%

Drawings And Specifications

Practice questions covering structural drawings interpretation, rebar symbols, bar bending schedules (BBS), concrete cover specifications, and anchorage guidelines.

20%

Rebar Materials And Properties

Practice questions covering different rebar grades, steel reinforcement types, standard sizes, physical/mechanical properties, and storage/protection guidelines.

20%

Tools And Equipment

Practice questions covering hand tools (pincers, wire cutters), bending tables/keys, power benders and cutters, safety measures, and machine maintenance.

20%

Cutting Bending And Assembly

Practice questions covering practical fabrication: bending techniques, tolerance limits, wire tying methods (slash, ring, saddle ties), lap splicing, anchoring, and positioning in slabs, columns, beams, and foundations.

How to Pass the SVP Steel Fixer Exam

What You Need to Know

Passing score: 50% (theory) + pass practical
Assessment: Multiple-choice computerised exam administered by Takamol Holding / Professional Accreditation Center (PACC), MHRSD.
Time limit: 2.0 hours
Exam fee: Varies by country (sponsored or employer-paid)

Keys to Passing

Complete 500+ practice questions
Score 80%+ consistently before scheduling
Focus on highest-weighted sections
Use our AI tutor for tough concepts

SVP Steel Fixer Study Tips from Top Performers

1Carefully study safety rules, especially safety harness usage when working at heights.

2Understand bar bending schedule (BBS) calculation formulas and standard bending angles/diameters.

3Master the difference between wire tying methods such as snap ties, saddle ties, and wrap-and-snap ties.

Frequently Asked Questions

What is the passing score for SVP Steel Fixer?

The passing score is 50% for the theoretical exam, plus a pass on the practical hands-on assessment.

Who administers the SVP Steel Fixer exam?

The exam is administered by the Takamol Holding / Professional Accreditation Center (PACC) under the Saudi Ministry of Human Resources and Social Development (MHRSD).

100+ Free SVP Steel Fixer Practice Questions

Explore More Saudi Skill Verification Program (SVP) Construction Trades

Saudi Skill Verification Program - Building Electrician

Saudi Skill Verification Program - Carpenter (Saudi Arabia)

Saudi Skill Verification Program - HVAC / AC Technician (Saudi Arabia)

Saudi Skill Verification Program - Industrial Electrician (Saudi Arabia)

Saudi Skill Verification Program - Mason / Block Mason

Saudi Skill Verification Program - Pipefitter