All Practice Exams

100+ Free RBSE Sec Voc Plumbing Practice Questions

Rajasthan RBSE Secondary Plumbing — Vocational Code 111 practice questions are available now; exam metadata is being verified.

✓ No registration✓ No credit card✓ No hidden fees✓ Start practicing immediately
See RBSE subject-wise statistics for the current cycle on statistics2026.htm. Pass Rate
100+ Questions
100% Free

Loading practice questions...

2026 Statistics

Key Facts: RBSE Sec Voc Plumbing Exam

111

RBSE subject code for Plumbing

RBSE Secondary/Praveshika 2026 subject-wise statistics

80 + 20

Typical Theory + Sessional full marks pattern (total 100)

RBSE Class 10 syllabus examination scheme

3 h 15 m

Typical theory paper duration

RBSE Class 10 syllabus

33%

Common minimum pass threshold under RBSE regulations

RBSE examination regulations (confirm circular)

2026

Main examination cycle evidenced in official subject-wise statistics

rajeduboard.rajasthan.gov.in/statistics2026.htm

MCQ study aid

Local bank adapts knowledge to four-option MCQs; official paper is mixed format

OpenExamPrep assessment-format policy

RBSE Secondary (Class 10) Plumbing (code 111): mixed board paper, typically Theory 80 + Sessional 20 = 100, 3h15m. Pass about 33% per RBSE rules. Fee as per board notification. Free English MCQ study aid — not a full mixed-paper simulation.

Sample RBSE Sec Voc Plumbing Practice Questions

Try these sample questions to test your RBSE Sec Voc Plumbing exam readiness. Each question includes a detailed explanation. Start the interactive quiz above for the full 100+ question experience with AI tutoring.

1Which plastic pipe is commonly preferred for hot-water distribution lines in residential plumbing because it handles higher temperatures than ordinary uPVC?
A.CPVC pipe
B.Clay sewer pipe
C.Unreinforced concrete pipe
D.Lead pipe
Explanation: CPVC (chlorinated PVC) is formulated for higher service temperatures and is widely used for hot-water supply lines, while ordinary uPVC is mainly for cold water or drainage.
2GI pipe in plumbing practice stands for:
A.Galvanized Iron pipe
B.Glass Insulation pipe
C.Ground Injection pipe
D.General Industrial plastic
Explanation: GI means galvanized iron—steel pipe coated with zinc for corrosion resistance, historically common for water supply.
3Why is zinc coating applied on galvanized iron (GI) pipes?
A.To protect the steel from rust and corrosion
B.To make the pipe magnetic for detection only
C.To increase electrical conductivity for earthing
D.To allow solvent-cement joints like plastic pipe
Explanation: Zinc galvanizing sacrifices preferentially and slows rusting of the underlying steel in water and atmospheric exposure.
4Which fitting changes the direction of a pipeline by 90 degrees?
A.Elbow
B.Coupling
C.Union
D.Nipple
Explanation: An elbow (90° or 45°) changes flow direction; couplings join straight runs, unions allow disconnection, nipples are short male-threaded pieces.
5A reducing tee is used when you need to:
A.Branch a line while changing branch or run size relative to the main
B.Increase pressure without changing diameter
C.Convert a valve into a pump
D.Seal a pipe permanently without any opening
Explanation: A reducing tee has at least one outlet of different size so you can take a branch or continue a run at a different diameter.
6Which valve is best suited when you need either fully open or fully closed service with minimal flow restriction when open?
A.Gate valve
B.Needle valve used as the only house shutoff
C.Check valve used as a manual shutoff
D.Safety relief valve used as daily isolation
Explanation: Gate valves are designed for isolation with a full-bore path when open; they are not ideal for throttling.
7A globe valve is preferred over a gate valve when the main purpose is to:
A.Throttle or regulate flow rate
B.Provide the absolute lowest pressure drop when fully open only
C.Act only as a non-return device
D.Join two plastic pipes with solvent cement
Explanation: Globe valves have a tortuous path that allows better throttling/control; gate valves are better for on/off isolation with lower drop when fully open.
8A check valve (non-return valve) is installed mainly to:
A.Allow flow in one direction and prevent reverse flow
B.Increase water temperature
C.Filter sand from the water continuously
D.Measure flow in litres per minute
Explanation: Check valves open with forward flow and close against reverse flow to protect pumps, tanks, and contamination paths.
9Ball valves are popular in modern plumbing isolation because they:
A.Open and close quickly with a quarter-turn and give a reliable shutoff
B.Must be rotated thirty full turns to open
C.Only work on gas lines and never on water
D.Replace the need for any pipe insulation
Explanation: Quarter-turn ball valves give fast, positive isolation and are widely used on water services.
10Which material is generally NOT acceptable for new potable (drinking) water pipes in modern practice?
A.Lead pipe
B.Copper pipe
C.CPVC pipe
D.HDPE pipe (where approved)
Explanation: Lead can leach toxic metal into drinking water and is obsolete/banned for potable systems; copper, CPVC, and approved HDPE are common potable options.

About the RBSE Sec Voc Plumbing Practice Questions

Verified exam format metadata for Rajasthan RBSE Secondary Plumbing — Vocational Code 111 is pending. The practice questions above remain available while official exam length, timing, passing score, fee, and administrator details are reviewed.