All Practice Exams

100+ Free Maharashtra SSC Plumber (General) Pre-Voc/NSQF Practice Questions

Maharashtra Secondary School Certificate (SSC / Class 10) Plumber (General) pre-vocational / NSQF skill subject — MSBSHSE (commonly code 98 Plumber-General on modern subject lists; confirm hall ticket) practice questions are available now; exam metadata is being verified.

✓ No registration✓ No credit card✓ No hidden fees✓ Start practicing immediately
Not published as a fixed subject-wise standing figure for this elective Pass Rate
100+ Questions
100% Free

Loading practice questions...

2026 Statistics

Key Facts: Maharashtra SSC Plumber (General) Pre-Voc/NSQF Exam

Code ~98 lineage

Plumber-General commonly listed near SSC subject code 98 on modern lists (confirm hall ticket)

MSBSHSE SSC subject list practice

Pre-voc / NSQF

Class 10 skill subject emphasising entry-level Plumber-General competencies

MSBSHSE/DVET pre-vocational patterns

Theory + practical

Typical assessment mixes written theory with workshop and project evidence

NSQF/pre-vocational board pattern summaries

35%

Common minimum passing floor per SSC subject under MSBSHSE

Maharashtra SSC pass-mark practice

Fees via school

Examination fees notified by MSBSHSE and collected through affiliated schools

MSBSHSE fee circular practice

English MCQ adaptation

This free local bank is not the official SSC paper or practical certificate

OpenExamPrep practice policy

Maharashtra MSBSHSE SSC Plumber (General) pre-voc/NSQF (code 98 lineage) is a Class 10 skill subject with theory + practical/project evidence and ~35% pass floor. Free 2026 English MCQ bank covers safety, tools, pipes, fittings, supply, drainage, fixtures, and employability—not a pure MCQ official paper or practical cert substitute.

Sample Maharashtra SSC Plumber (General) Pre-Voc/NSQF Practice Questions

Try these sample questions to test your Maharashtra SSC Plumber (General) Pre-Voc/NSQF exam readiness. Each question includes a detailed explanation. Start the interactive quiz above for the full 100+ question experience with AI tutoring.

1In plumbing, PPE most urgently needed when cutting metal pipe with a hacksaw is:
A.Safety goggles and gloves
B.Only hearing protection (earplugs)
C.Open-toed sandals
D.A dust mask only
Explanation: Eye and hand protection reduce cuts and flying metal particles when sawing pipe.
2GI pipe in basic plumbing stands for pipe that is:
A.Green insulated only
B.Galvanised iron (zinc-coated steel)
C.Glass-lined copper only
D.Gold-inlaid plastic only
Explanation: GI means galvanised iron: steel pipe protected with a zinc coating against rust.
3PVC water pipe is popular for cold-water lines mainly because it is:
A.Made of pure lead
B.Heavier than cast iron always
C.Light, corrosion-resistant, and easy to join
D.Always the only legal hot-steam pipe
Explanation: PVC is light, resists corrosion, and joins with solvent cement or push fittings for cold water.
4A pipe wrench is primarily used to:
A.Measure body temperature
B.Cut glass tiles
C.Paint walls only
D.Grip and turn threaded pipes and fittings
Explanation: Pipe wrenches grip round pipe so threaded joints can be tightened or loosened.
5The main purpose of a water trap under a wash basin is to:
A.Hold a water seal that blocks sewer gas
B.Heat the water for bathing
C.Act as an electrical fuse
D.Increase water bill deliberately
Explanation: The trap retains a water seal so foul sewer gases cannot rise into the room.
6Before using a power drill on site, a safe first step is to:
A.Remove all guards permanently
B.Check the cable, bit, and work area for hazards
C.Work barefoot for better grip
D.Ignore wet floors near electricity
Explanation: Inspect tools, bits, and surroundings so electrical and mechanical hazards are controlled before drilling.
7An elbow fitting is used to:
A.Replace a water meter always
B.Paint the ceiling
C.Change the direction of a pipe run
D.Measure chlorine in water
Explanation: Elbows turn the pipe path, commonly 90° or 45°, without sharp kinks in soft materials.
8A tee fitting allows a pipeline to:
A.Become a solid rod only
B.Stop all flow permanently without a valve
C.Double as a roof tile
D.Branch into three directions at a joint
Explanation: A tee creates a branch connection so flow can split or join at a three-way joint.
9Which unit is commonly used for pipe diameter in Indian plumbing practice?
A.Millimetres or inches (nominal sizes)
B.Decibels only
C.Celsius only
D.Light-years
Explanation: Pipe sizes are quoted in millimetres or nominal inches depending on product standards.
10A stopcock on a domestic supply is mainly used to:
A.Decorate the kitchen only
B.Isolate (shut off) water flow for repair
C.Generate electricity
D.Filter sand automatically always
Explanation: Stopcocks and isolation valves shut water so fixtures or pipe sections can be repaired safely.

About the Maharashtra SSC Plumber (General) Pre-Voc/NSQF Practice Questions

Verified exam format metadata for Maharashtra Secondary School Certificate (SSC / Class 10) Plumber (General) pre-vocational / NSQF skill subject — MSBSHSE (commonly code 98 Plumber-General on modern subject lists; confirm hall ticket) is pending. The practice questions above remain available while official exam length, timing, passing score, fee, and administrator details are reviewed.