In a standard four-stroke operating cycle of a reciprocating piston engine (Otto cycle), how many degrees of crankshaft rotation are required to complete one full cycle of events?
Reciprocating Piston Engines
Question · Easy
What is the primary aerodynamic and thermodynamic purpose of valve overlap in a four-stroke aircraft piston engine?
Which surface treatment process is commonly applied to steel aircraft cylinder barrels to produce an extremely hard, wear-resistant interior surface while retaining core toughness?
What is the primary function of the oil control ring installed on an aircraft engine piston?
Dynamic counterweights (pendulum dampers) fitted to aircraft engine crankshafts are designed to damp out which specific structural hazard?
In a radial aircraft piston engine, what type of connecting rod assembly is utilized to connect all pistons in a single cylinder bank to the single crankpin?
What is the standard firing order for a typical four-cylinder horizontally opposed aircraft engine (e.g., Lycoming O-360)?
What primary operational advantage do hydraulic valve lifters (tappets) provide in aircraft engines over solid mechanical lifters?
Which of the following conditions distinguishes detonation from pre-ignition in a reciprocating engine?
Question · Medium
An aircraft cylinder has a swept volume (piston displacement) of 90 cubic inches and a clearance volume of 15 cubic inches. What is the compression ratio of this cylinder?
An intake valve opens 15 degrees before TDC and closes 50 degrees after BDC. What is the total duration of time (in degrees of crankshaft rotation) that the intake valve remains open?
In an aircraft engine turbocharger system, what component directly regulates the amount of exhaust gas directed through the turbine wheel?
What is defined as the 'critical altitude' of a turbocharged aircraft engine?
What operational hazard is described as 'bootstrapping' in a turbocharged engine system equipped with a manual wastegate?
What type of gudgeon pin (piston pin) design is free to rotate in both the piston bosses and the small-end connecting rod bushing?
In a four-stroke reciprocating engine, what is the rotational speed of the camshaft relative to the crankshaft?
Calculate the total piston displacement of a 6-cylinder engine having a cylinder bore of 5.0 inches and a stroke of 4.0 inches. (Use π = 3.1416)
What is the primary cause of an engine 'backfire' through the induction manifold during engine operation with an excessively lean fuel-air mixture?
What method is used in high-performance aircraft piston engines to cool the undersides of piston crowns during operation?
Why are aircraft cylinder heads constructed from aluminum alloy while the cylinder barrel is made of forged alloy steel?
In a dual-actuated automatic turbocharger control system, what is the function of the differential pressure controller?
Calculate the Indicated Horsepower (IHP) of a 4-stroke, 6-cylinder engine with: IMEP = 125 psi, Stroke = 0.5 ft (6 in), Cylinder Area = 20 sq in, RPM = 2700.
Question · Hard
What effect does high intake manifold air temperature (IAT) have on the volumetric efficiency and power output of a supercharged piston engine?
Why are some aircraft engine cylinders manufactured with a 'choke bore' (tapered bore)?
What mechanical phenomenon causes critical crankshaft speeds in reciprocating engines, necessitating restricted RPM operating ranges marked in red/yellow arc on tachometers?
Which thermodynamic cycle forms the theoretical operational basis for all gas turbine engines?
Gas Turbine Engine Fundamentals
What is a major inherent advantage of a centrifugal flow compressor over an axial flow compressor in gas turbine engines?
In a gas turbine combustion chamber, approximately what percentage of total compressor airflow is used as primary air for direct fuel combustion?
Which cooling method involves discharging high-pressure compressor bleed air through small micro-holes on the leading edge of a turbine blade to form a insulating boundary layer?
What type of exhaust nozzle geometry is used on subsonic aircraft gas turbine engines to accelerate exhaust gas to maximum velocity?
What is the key structural characteristic of a 'free-turbine' turboshaft or turboprop engine?
What is an immediate cock-pit indication of a compressor stall in a gas turbine engine?
What aerodynamic transformation occurs across the compressor diffuser section before air enters the combustor?
In an axial flow compressor stage, what are the respective roles of the rotor blades and stator vanes?
What failure mechanism in turbine rotor blades is characterized by permanent, slow plastic elongation over time due to combined high centrifugal stress and extreme operating temperatures?
Engine Pressure Ratio (EPR) is used as a primary thrust indication on many turbojet/turbofan engines. How is EPR calculated?
How do Variable Stator Vanes (VSV) and compressor bleed valves operate together during engine acceleration at low RPM to prevent compressor stall?
What is the definition of the bypass ratio in a turbofan engine?
What is the primary function of an Active Clearance Control (ACC) system in modern high-bypass turbofan engines?
What operational advantage is gained by configuring a reverse-flow combustor in a turboprop engine (such as the Pratt & Whitney PT6)?
How do impulse turbine stage blades differ aerodynamically from reaction turbine stage blades?
What is the effect of injecting water/methanol mixture into the compressor intake of a gas turbine engine during high ambient temperature takeoff?
How does a torquemeter system in a turboprop engine measure engine power output?
In a twin-spool axial turbofan engine, which spool is driven by the High-Pressure (HP) turbine?
What aerodynamic condition occurs at the throat of a turbine nozzle guide vane (NGV) when exhaust gas flow reaches sonic velocity (Mach 1.0)?
A turbojet engine ingests air at mass flow rate m = 50 kg/s. Aircraft flight velocity V0 = 200 m/s. Exhaust gas discharge velocity Vej = 600 m/s. (Assume nozzle pressure ratio is choked so Pej = Pamb). Calculate Net Thrust Fn.
A jet engine produces a net thrust of 25,000 N while flying at a true airspeed of 240 m/s. The engine consumes fuel at rate of 1.2 kg/s. Fuel heating value Q = 43,000,000 J/kg. Calculate Overall Efficiency (η_overall).
What is the propagation behavior of a 'rotating stall' cell around an axial compressor annulus during partial compressor instability?
Loading more…