In an aluminum screen wall, what is the primary purpose of diagonal corner cable bracing?
Wall Sections
Question · Medium
OSHA fall heights, to scale
Short
A screen wall is 12 ft long with posts spaced 4 ft on center, including a post at each end. How many posts are required?
When anchoring an aluminum screen wall post to an existing concrete slab, which fastener type is appropriate for the base connection?
Trades Exam Prep Podcast
Listen on Spotify
Podcast
What reference primarily governs the allowable post and beam spacing for aluminum screen walls in Florida high-wind zones?
Question · Easy
A wall 24 ft long has posts spaced 6 ft on center with a post at each end. How many posts are required?
Six feet: a hard-hat anthem
When tying a new aluminum-framed wall into an existing structure with steel members, what is the controlling consideration for fastener selection beyond load?
Question · Hard
On a composite metal panel wall, what governs the fastener spacing along panel edges?
In specialty structure work, what is a framed solid (metal) wall?
Fasteners are placed every 12 in along an 96 in track, with a fastener at both ends. How many fasteners are needed for one track?
When installing a screen and storm door, what must be verified before hanging the door?
Screen comes on a roll 36 in wide by 100 ft long. Each screen wall panel opening is 36 in wide by 96 in tall, with the screen applied in one width per panel. How many full panels can be screened from one roll?
Under the Florida Building Code, what determines the design wind speed for a specialty structure project?
What is the purpose of a starter strip in siding or wall panel installation?
Galvanic corrosion of aluminum is most likely to occur when aluminum is in direct, moist contact with which material?
For an aluminum screen wall in a high-wind zone, what does the Guide to Aluminum Construction in High Wind Areas provide that the installer must follow?
In a standing seam aluminum pan roof, what does the standing seam do?
Roof Sections
On an aluminum screen roof, which fastening detail most directly resists wind uplift at the post-to-beam connection?
A patio roof has a 4:12 slope and a horizontal run of 12 ft. Using the Pythagorean theorem, what is the approximate slope (rafter) length?
What is the purpose of flashing where a roof meets a wall?
Which sealant chemistry is generally compatible with aluminum and widely used on aluminum roof seams?
A patio roof covers 20 ft by 30 ft. Standing seam panels 2 ft wide run the 30 ft length, laid across the 20 ft width. How many panels are needed?
Which approved reference is the primary source for high-wind aluminum roof assembly spans and connections?
In roof framing, structural spacing and support charts are commonly referred to as what?
Standing seam pans are 16 in wide with a 1 in side lap, giving 15 in of net coverage each. How many pans are needed to cover a 30 ft (360 in) roof width?
A through-fastened (exposed-fastener) corrugated metal panel roof generally requires a minimum slope of about:
On an aluminum standing seam roof, over-tightening a through-fastened screw at a panel clip tends to cause what problem?
What is the function of a ridge cap on a metal roof?
What tool is used to bend aluminum fascia, trim, and roof flashing on site?
An attic roof area is 40 ft by 50 ft (2,000 sq ft). Using a 1:300 ventilation ratio, what is the required total net free vent area?
Why must aluminum roof panels be allowed to move thermally rather than being rigidly fixed at both ends?
Under the specialty structure scope, residential glass window and door installations are limited to what building height?
Windows
When setting a window into a masonry rough opening, what is the standard installation sequence for sealing?
A window rough opening is 36 in wide by 48 in tall. The window requires a 1/4 in clearance all around for shimming and movement. What is the window's nominal size to fit the opening?
Which standard is referenced by the Florida Building Code for window and door assemblies installed under the specialty structure scope?
When installing a vinyl window in a wood frame wall, where should shims be placed?
A window measures 60 in wide by 48 in tall. What is its area in square feet?
In the High-Velocity Hurricane Zone, which approval is required before a hurricane protection device (shutter or impact glazing) may be installed?
When fastening a window jamb into a metal-framed wall, what is the standard method?
What is the primary purpose of a sill pan under a window?
A 48 in tall window jamb is fastened every 12 in with a fastener at the top and at the bottom. How many fasteners does one jamb require?
For a window, the FBC component-and-cladding wind pressure depends on which set of inputs?
When replacing a window in an existing wall, what must be verified about the rough opening before the new unit is set?
A sill pan must slope in which direction to drain correctly?
A window has 6 fasteners on each of two jambs, 4 on the head, and 4 on the sill. What is the total number of fasteners for the window?
In a wind-borne debris region, which combination satisfies the FBC opening-protection requirement for a window?
Loading more…