Per ASCE 7, the MINIMUM uniform live load for the floor of a typical office (above first floor, no partition allowance) is closest to which value?
Gravity Loads
Question · Easy
Where does this beam break first?
Short
ASCE 7 permits live-load reduction for members supporting a tributary area where K_LL × A_T exceeds which value?
An interior column supports four 25 ft × 25 ft bays of office floor (L_o = 50 psf). What is the live-load influence area used in ASCE 7 reduction (K_LL × A_T)?
Question · Medium
Engineering Exam Prep Podcast
Listen on Spotify
Podcast
In ASCE 7, the flat-roof snow load is calculated as p_f = 0.7 × C_e × C_t × I_s × p_g. The 0.7 factor primarily accounts for which physical effect?
A heated, partially exposed monoslope roof (C_e = 1.0, C_t = 1.0, I_s = 1.0) sits in a region with p_g = 40 psf. Ignoring slope reduction and drift, the flat-roof snow load p_f is closest to:
Which ASCE 7 strength load combination governs uplift checks on a light wood-frame roof with no live load present and high wind?
Load Combinations
In ASCE 7 strength-design seismic combinations, the redundancy factor rho multiplies which quantity?
Per ASCE 7, what is the basic wind speed V used for Risk Category II buildings?
Wind Loads
In ASCE 7, the velocity pressure q_z is given by q_z = 0.00256 × K_z × K_zt × K_d × K_e × V^2. The K_d directionality factor for MWFRS of a typical building is closest to:
Which ASCE 7 wind procedure typically governs cladding fasteners on a roof corner zone?
For a low-rise building (h <= 60 ft, simple geometry), which ASCE 7 MWFRS procedure is generally most economical and commonly used?
What is the purpose of the gust effect factor G in ASCE 7 wind design?
An enclosed building has internal pressure coefficient (GC_pi) values per ASCE 7 of:
ASCE 7 Exposure Category C is described as:
Per ASCE 7 seismic design, which parameter MOST DIRECTLY determines the Seismic Design Category (SDC) for a Risk Category II building?
Seismic Design
In the ASCE 7 Equivalent Lateral Force (ELF) procedure, the seismic response coefficient C_s for short-period structures is governed by which expression?
An office building has S_DS = 1.0 g, R = 8 (special steel moment frame), I_e = 1.0, W = 5,000 kips, T = 0.6 s, S_D1 = 0.6 g. The seismic base shear V is closest to:
Question · Hard
ASCE 7 introduced multi-period response spectra (MPRS) for site-specific design replacing the two-parameter (S_DS, S_D1) approach in newer editions. The PRIMARY motivation was to:
A 10-story building has fundamental period T_a estimated using ASCE 7 approximate formula T_a = C_t × h_n^x. For a steel moment-resisting frame, C_t and x are:
ASCE 7 vertical distribution of seismic forces uses F_x = C_vx × V, where C_vx = w_x × h_x^k / sum(w_i × h_i^k). The exponent k depends on:
Per ASCE 7, modal response spectrum analysis is REQUIRED (rather than ELF being permitted) when:
Allowable story drift for a Risk Category II building with masonry shear walls (other masonry structures) per ASCE 7 Table 12.12-1 is closest to:
The ASCE 7 P-delta stability check uses a stability coefficient theta. P-delta need NOT be considered when:
A Type 1a horizontal irregularity (torsional) per ASCE 7 exists when the maximum story drift at one end exceeds the average story drift at the two ends by what factor?
A soft story (Type 1a vertical stiffness irregularity) is defined as a story where the lateral stiffness is less than what fraction of the story above?
ACI 318 strength reduction factor phi for tension-controlled flexure of a non-prestressed reinforced concrete beam is:
Concrete Design
For a rectangular concrete beam with f'c = 5,000 psi, what is the value of beta_1 used in the equivalent rectangular stress block?
A singly reinforced concrete beam has b = 12 in, d = 22 in, A_s = 3.0 in^2, f'c = 4,000 psi, f_y = 60 ksi. Assuming tension-controlled, the nominal moment capacity M_n is closest to:
Per ACI 318, the maximum reinforcement ratio rho_max for a tension-controlled flexural section is governed by limiting:
When is compression reinforcement (doubly reinforced design) typically REQUIRED in a beam?
For two-way slabs, the ACI 318 Direct Design Method (DDM) imposes which key limitation?
Punching shear in a flat plate around an interior column is typically checked using a critical perimeter located at:
Per ACI 318, the basic development length l_d for a deformed bar in tension increases with:
The minimum tension lap splice length per ACI 318 for a Class B splice is:
Per ACI 318, hooked development length l_dh for a standard hook is reduced from the basic value by which beneficial confinement?
ACI 318 minimum shear reinforcement is required in beams when V_u exceeds:
ACI 318 Chapter 18 (seismic) Special Moment Frame (SMF) beams in flexure require which minimum reinforcement at top and bottom across the full member length?
Concrete Seismic
In ACI 318 Special Structural Walls, the boundary element provisions are required when the maximum extreme-fiber compressive strain under design displacement exceeds:
In ACI 318 Special Moment Frames, the strong-column weak-beam check requires the sum of column flexural strengths at a joint be at LEAST what multiple of the sum of beam flexural strengths?
ACI 318 torsion design requires consideration when the threshold torsion T_u exceeds approximately:
AISC 360 LRFD resistance factor phi_b for flexure of compact W-shape beams (full plastic moment) is:
Steel Design
A compact W-shape beam has L_b = 8 ft (unbraced length) and L_p = 6 ft, L_r = 18 ft. The flexural strength M_n is governed by:
AISC 360 lateral-torsional buckling modification factor C_b for a simply supported W-shape beam under uniformly distributed load with no intermediate bracing is:
For an axially loaded W-shape column, AISC 360 distinguishes inelastic from elastic flexural buckling using the slenderness ratio threshold:
AISC 360 effective length factor K for a column with both ends pinned and free to translate (sway) is theoretically:
In an AISC 360 composite beam (steel beam + concrete slab) acting fully composite, the shear connectors at the steel-concrete interface must be designed to resist:
Loading more…